-- -- Copyright(C) 2005-2018 ALAXALA Networks Corporation. All Rights Reserved. -- -- AX3630S-MIB.my: Switching Router System information MIB file -- AX3630S DEFINITIONS ::= BEGIN IMPORTS enterprises, OBJECT-TYPE, NetworkAddress, IpAddress, Counter, Gauge, TimeTicks FROM RFC1155-SMI RouterID, AreaID, Status, BigMetric, DesignatedRouterPriority, HelloRange, Metric, PositiveInteger, UpToMaxAge FROM OSPF-MIB OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 ifIndex FROM IF-MIB DisplayString FROM RFC1213-MIB RowStatus, MacAddress, TruthValue, TimeStamp, PhysAddress FROM SNMPv2-TC InterfaceIndex FROM IF-MIB Ipv6IfIndex, Ipv6Address, Ipv6AddressPrefix FROM IPV6-TC BridgeId, Timeout FROM BRIDGE-MIB PortList FROM Q-BRIDGE-MIB InterfaceIndex FROM IF-MIB InetAddressType,InetAddress FROM INET-ADDRESS-MIB Gauge32, Counter32, Counter64, Unsigned32, Integer32 FROM SNMPv2-SMI ; VlanIndex ::= INTEGER (1..2147483647) VlanIdOrZero ::= INTEGER (0|1..4094) -- object syntax difinition end alaxala OBJECT IDENTIFIER ::= { enterprises 21839 } alaxalaProductId OBJECT IDENTIFIER ::= { alaxala 1 } axSwitch OBJECT IDENTIFIER ::= { alaxalaProductId 2 } ax3630s OBJECT IDENTIFIER ::= { axSwitch 7 } ax3640s OBJECT IDENTIFIER ::= { axSwitch 11 } ax3650s OBJECT IDENTIFIER ::= { axSwitch 15 } ax3830s OBJECT IDENTIFIER ::= { axSwitch 17 } alaxalaMib OBJECT IDENTIFIER ::= { alaxala 2 } axsEx OBJECT IDENTIFIER ::= { alaxalaMib 2 } axsMib OBJECT IDENTIFIER ::= { axsEx 1 } ax3630sMib OBJECT IDENTIFIER ::= { axsEx 7 } ax3640sMib OBJECT IDENTIFIER ::= { axsEx 11 } ax3650sMib OBJECT IDENTIFIER ::= { axsEx 15 } ax3830sMib OBJECT IDENTIFIER ::= { axsEx 17 } -- device independent axsStats OBJECT IDENTIFIER ::= { axsMib 1 } axsIfStats OBJECT IDENTIFIER ::= { axsStats 4 } axsQoS OBJECT IDENTIFIER ::= { axsStats 6 } axsEtherTxQoS OBJECT IDENTIFIER ::= { axsQoS 1 } axsEthShaper OBJECT IDENTIFIER ::= { axsQoS 4 } axsEthShaperAgQue OBJECT IDENTIFIER ::= { axsQoS 5 } axsToCpuQoS OBJECT IDENTIFIER ::= { axsQoS 11 } axsDHCP OBJECT IDENTIFIER ::= { axsStats 10 } axsGsrp OBJECT IDENTIFIER ::= { axsMib 4 } axsFdb OBJECT IDENTIFIER ::= { axsMib 5 } axsVlan OBJECT IDENTIFIER ::= { axsMib 6 } axsVlanBridge OBJECT IDENTIFIER ::= { axsVlan 1 } axsVlanBridgeBase OBJECT IDENTIFIER ::= { axsVlanBridge 1 } axsVlanBridgeStp OBJECT IDENTIFIER ::= { axsVlanBridge 2 } axsVlanBridgeTp OBJECT IDENTIFIER ::= { axsVlanBridge 4 } axsVlanBridgeStatic OBJECT IDENTIFIER ::= { axsVlanBridge 5 } axsVlanTagTranslation OBJECT IDENTIFIER ::= { axsVlan 10 } axsOadp OBJECT IDENTIFIER ::= { axsMib 7 } axsOadpMIBObjects OBJECT IDENTIFIER ::= { axsOadp 1 } axsOadpGlobalInfo OBJECT IDENTIFIER ::= { axsOadpMIBObjects 1 } axsOadpPortInfo OBJECT IDENTIFIER ::= { axsOadpMIBObjects 2 } axsOadpNeighborInfo OBJECT IDENTIFIER ::= { axsOadpMIBObjects 3 } axsOadpMIBNotifications OBJECT IDENTIFIER ::= { axsOadp 2 } axsFlow OBJECT IDENTIFIER ::= { axsMib 8 } axsAccessFilterStats OBJECT IDENTIFIER ::= {axsFlow 9} axsQosFlowStats OBJECT IDENTIFIER ::= {axsFlow 11} axsL2ld OBJECT IDENTIFIER ::= {axsMib 10} axsL2ldGlobalInfo OBJECT IDENTIFIER ::= {axsL2ld 1} axsVrf OBJECT IDENTIFIER ::= { axsMib 11 } axsVrfIp OBJECT IDENTIFIER ::= { axsVrf 1 } axsVrfIpForward OBJECT IDENTIFIER ::= { axsVrf 2 } axsVrfIpv6 OBJECT IDENTIFIER ::= { axsVrf 3 } axsVrfIpv6Forward OBJECT IDENTIFIER ::= { axsVrf 4 } axsOspf OBJECT IDENTIFIER ::= { axsMib 14 } axsOspfTrap OBJECT IDENTIFIER ::= { axsOspf 16 } axsOspfTraps OBJECT IDENTIFIER ::= { axsOspfTrap 2 } axsOspfv3 OBJECT IDENTIFIER ::= { axsMib 15 } axsStatic OBJECT IDENTIFIER ::= { axsMib 38 } axsStaticTrap OBJECT IDENTIFIER ::= { axsStatic 2 } axsUlr OBJECT IDENTIFIER ::= { axsMib 20 } axsUlrGlobalInfo OBJECT IDENTIFIER ::= { axsUlr 1 } axsTrackObject OBJECT IDENTIFIER ::= { axsMib 41 } axsTrackObjectGeneralGroup OBJECT IDENTIFIER ::= { axsTrackObject 1 } axsTrackObjectTraps OBJECT IDENTIFIER ::= { axsTrackObject 2 } axsPolicyBase OBJECT IDENTIFIER ::= { axsMib 45 } axsPolicyBaseRouting OBJECT IDENTIFIER ::= { axsPolicyBase 1 } axsBootManagement OBJECT IDENTIFIER ::= { axsMib 51 } axsLogin OBJECT IDENTIFIER ::= { axsMib 52 } axslldp OBJECT IDENTIFIER ::= { axsMib 100 } axslldpConfiguration OBJECT IDENTIFIER ::= { axslldp 1 } axslldpStats OBJECT IDENTIFIER ::= { axslldp 2 } axslldpLocalSystemData OBJECT IDENTIFIER ::= { axslldp 3 } axslldpRemoteSystemData OBJECT IDENTIFIER ::= { axslldp 4 } axslldpRemoteOriginInfoData OBJECT IDENTIFIER ::= { axslldp 20 } axsAxrp OBJECT IDENTIFIER ::= { axsMib 200 } axsPconMIB OBJECT IDENTIFIER ::= { axsMib 300 } axsPconObjects OBJECT IDENTIFIER ::= { axsPconMIB 1 } axsPconModuleData OBJECT IDENTIFIER ::= { axsPconObjects 1 } axsPconPowerCon OBJECT IDENTIFIER ::= { axsPconObjects 2 } axsPconTraffic OBJECT IDENTIFIER ::= { axsPconObjects 3 } ax3630sSwitch OBJECT IDENTIFIER ::= { ax3630sMib 1 } ax3630sSoftware OBJECT IDENTIFIER ::= { ax3630sSwitch 2 } ax3630sSystemMsg OBJECT IDENTIFIER ::= { ax3630sSwitch 3 } ax3630sSnmpAgent OBJECT IDENTIFIER ::= { ax3630sSwitch 4 } ax3630sLicense OBJECT IDENTIFIER ::= { ax3630sSwitch 6 } ax3630sDevice OBJECT IDENTIFIER ::= { ax3630sMib 2 } ax3630sChassis OBJECT IDENTIFIER ::= { ax3630sDevice 1 } ax3630sPhysLine OBJECT IDENTIFIER ::= { ax3630sDevice 2 } ax3630sManagementMIB OBJECT IDENTIFIER ::= { ax3630sMib 3 } ax3630sOperationCommand OBJECT IDENTIFIER ::= { ax3630sManagementMIB 1 } ax3630sFdbClearMIB OBJECT IDENTIFIER ::= { ax3630sOperationCommand 1 } ax3640sSwitch OBJECT IDENTIFIER ::= { ax3640sMib 1 } ax3640sSoftware OBJECT IDENTIFIER ::= { ax3640sSwitch 2 } ax3640sSystemMsg OBJECT IDENTIFIER ::= { ax3640sSwitch 3 } ax3640sSnmpAgent OBJECT IDENTIFIER ::= { ax3640sSwitch 4 } ax3640sLicense OBJECT IDENTIFIER ::= { ax3640sSwitch 6 } ax3640sDevice OBJECT IDENTIFIER ::= { ax3640sMib 2 } ax3640sChassis OBJECT IDENTIFIER ::= { ax3640sDevice 1 } ax3640sPhysLine OBJECT IDENTIFIER ::= { ax3640sDevice 2 } ax3640sManagementMIB OBJECT IDENTIFIER ::= { ax3640sMib 3 } ax3640sOperationCommand OBJECT IDENTIFIER ::= { ax3640sManagementMIB 1 } ax3640sFdbClearMIB OBJECT IDENTIFIER ::= { ax3640sOperationCommand 1 } ax3650sSwitch OBJECT IDENTIFIER ::= { ax3650sMib 1 } ax3650sSoftware OBJECT IDENTIFIER ::= { ax3650sSwitch 2 } ax3650sSystemMsg OBJECT IDENTIFIER ::= { ax3650sSwitch 3 } ax3650sSnmpAgent OBJECT IDENTIFIER ::= { ax3650sSwitch 4 } ax3650sLicense OBJECT IDENTIFIER ::= { ax3650sSwitch 6 } ax3650sDevice OBJECT IDENTIFIER ::= { ax3650sMib 2 } ax3650sChassis OBJECT IDENTIFIER ::= { ax3650sDevice 1 } ax3650sPhysLine OBJECT IDENTIFIER ::= { ax3650sDevice 2 } ax3650sManagementMIB OBJECT IDENTIFIER ::= { ax3650sMib 3 } ax3650sOperationCommand OBJECT IDENTIFIER ::= { ax3650sManagementMIB 1 } ax3650sFdbClearMIB OBJECT IDENTIFIER ::= { ax3650sOperationCommand 1 } ax3830sSwitch OBJECT IDENTIFIER ::= { ax3830sMib 1 } ax3830sSoftware OBJECT IDENTIFIER ::= { ax3830sSwitch 2 } ax3830sSystemMsg OBJECT IDENTIFIER ::= { ax3830sSwitch 3 } ax3830sSnmpAgent OBJECT IDENTIFIER ::= { ax3830sSwitch 4 } ax3830sLicense OBJECT IDENTIFIER ::= { ax3830sSwitch 6 } ax3830sDevice OBJECT IDENTIFIER ::= { ax3830sMib 2 } ax3830sChassis OBJECT IDENTIFIER ::= { ax3830sDevice 1 } ax3830sPhysLine OBJECT IDENTIFIER ::= { ax3830sDevice 2 } ax3830sManagementMIB OBJECT IDENTIFIER ::= { ax3830sMib 3 } ax3830sOperationCommand OBJECT IDENTIFIER ::= { ax3830sManagementMIB 1 } ax3830sFdbClearMIB OBJECT IDENTIFIER ::= { ax3830sOperationCommand 1 } axsIfStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsIfStatsTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing extension statistics for more than 100,000,000 bps interface." ::= { axsIfStats 1 } axsIfStatsEntry OBJECT-TYPE SYNTAX AxsIfStatsTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing extension statistics for interface." INDEX { axsIfStatsIndex } ::= { axsIfStatsTable 1 } AxsIfStatsTableEntry ::= SEQUENCE { axsIfStatsIndex INTEGER, axsIfStatsName DisplayString, axsIfStatsInMegaOctets Counter, axsIfStatsInUcastMegaPkts Counter, axsIfStatsInMulticastMegaPkts Counter, axsIfStatsInBroadcastMegaPkts Counter, axsIfStatsOutMegaOctets Counter, axsIfStatsOutUcastMegaPkts Counter, axsIfStatsOutMulticastMegaPkts Counter, axsIfStatsOutBroadcastMegaPkts Counter, axsIfStatsHighSpeed Counter } axsIfStatsIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "This object value is same as Ifindex which interface index of a system." ::= { axsIfStatsEntry 1 } axsIfStatsName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Interfaces name. Same as ifDescr." ::= { axsIfStatsEntry 2 } axsIfStatsInMegaOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of octets that received on the interface. This value is displayed in mega-octets(M). Value of 0 through 999,999 are rounded down." ::= { axsIfStatsEntry 3 } axsIfStatsInUcastMegaPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of subnetwork-unicast packets that received on the interface. This value is displayed in mega-packets(M).Value of 0 through 999,999 are rounded down." ::= { axsIfStatsEntry 4 } axsIfStatsInMulticastMegaPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of multicast mega-packets that received on the interface. this value is displayed in mega-packets(M).Value of 0 through 999,999 are rounded down." ::= { axsIfStatsEntry 5 } axsIfStatsInBroadcastMegaPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of non-unicast packets delivered to a higher-layer protocol. The value is displayed in mega-packets (M). Value of 0 through 999,999 are rounded down. " ::= { axsIfStatsEntry 6 } axsIfStatsOutMegaOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets transmitted out of the interface. The value is displayed in mega-octets(M). Value of 0 through 999,999 are rounded down." ::= { axsIfStatsEntry 7 } axsIfStatsOutUcastMegaPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address.The value is displayed in mega packets(M). Value of 0 through 999,999 are rounded down." ::= { axsIfStatsEntry 8 } axsIfStatsOutMulticastMegaPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of multicast packets that transmitted on the interface. This value is displayed in mega-packets(M). Value of 0 through 999,999 are rounded down." ::= { axsIfStatsEntry 9 } axsIfStatsOutBroadcastMegaPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of broadcast packets that transmitted on the interface. This value is displayed in mega-packets(M). Value of 0 through 999,999 are rounded down. " ::= { axsIfStatsEntry 10 } axsIfStatsHighSpeed OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "A circuit speed.This value is displayed in mega-bps[Mbps]. Round off the 1,000,000bps. " ::= { axsIfStatsEntry 11 } -- QoS interface statistics Variables axsEtherTxQoSStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsEtherTxQoSStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A collection of QoS statistics kept for a particular Ethernet interface." ::= { axsEtherTxQoS 1 } axsEtherTxQoSStatsEntry OBJECT-TYPE SYNTAX AxsEtherTxQoSStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing QoS statistics for a particular Ethernet interface." INDEX { axsEtherTxQoSStatsIndex } ::= { axsEtherTxQoSStatsTable 1 } AxsEtherTxQoSStatsEntry ::= SEQUENCE { axsEtherTxQoSStatsIndex INTEGER, axsEtherTxQoSStatsMaxQnum INTEGER, axsEtherTxQoSStatsLimitQlen INTEGER, axsEtherTxQoSStatsTotalOutFrames Counter, axsEtherTxQoSStatsTotalOutBytesHigh Counter, axsEtherTxQoSStatsTotalOutBytesLow Counter, axsEtherTxQoSStatsTotalDiscardFrames Counter } axsEtherTxQoSStatsIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Identified by a particular value of this index is same value of ifIndex.Its value ranges between 1 and the value of ifNumber." ::= { axsEtherTxQoSStatsEntry 1 } axsEtherTxQoSStatsMaxQnum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max length of queue for an ethernet interface." ::= { axsEtherTxQoSStatsEntry 2 } axsEtherTxQoSStatsLimitQlen OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The limit length of outbound queue for an ethernet interface." ::= { axsEtherTxQoSStatsEntry 3 } axsEtherTxQoSStatsTotalOutFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets transmitted out of the interface." ::= { axsEtherTxQoSStatsEntry 4 } axsEtherTxQoSStatsTotalOutBytesHigh OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets transmitted out of the interface." ::= { axsEtherTxQoSStatsEntry 5 } axsEtherTxQoSStatsTotalOutBytesLow OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets transmitted out of the interface." ::= { axsEtherTxQoSStatsEntry 6 } axsEtherTxQoSStatsTotalDiscardFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of outbound packets which were chosen to be discarded ." ::= { axsEtherTxQoSStatsEntry 7 } axsEtherTxQoSStatsQueueTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsEtherTxQoSStatsQueueEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A collection of priority queue statistics." ::= { axsEtherTxQoS 2 } axsEtherTxQoSStatsQueueEntry OBJECT-TYPE SYNTAX AxsEtherTxQoSStatsQueueEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A entry of priority queue statistics." INDEX { axsEtherTxQoSStatsQueueIndex , axsEtherTxQoSStatsQueueQueIndex } ::= { axsEtherTxQoSStatsQueueTable 1 } AxsEtherTxQoSStatsQueueEntry ::= SEQUENCE { axsEtherTxQoSStatsQueueIndex INTEGER, axsEtherTxQoSStatsQueueQueIndex INTEGER, axsEtherTxQoSStatsQueueQlen INTEGER, axsEtherTxQoSStatsQueueMaxQlen INTEGER, axsEtherTxQoSStatsQueueDiscardFramesClass1 Counter64, axsEtherTxQoSStatsQueueDiscardFramesClass2 Counter64, axsEtherTxQoSStatsQueueDiscardFramesClass3 Counter64, axsEtherTxQoSStatsQueueDiscardFramesClass4 Counter64 } axsEtherTxQoSStatsQueueIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Identified by a particular value of this index is same value of ifIndex.Its value ranges between 1 and the value of ifNumber." ::= { axsEtherTxQoSStatsQueueEntry 1 } axsEtherTxQoSStatsQueueQueIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "An index that uniquely identifies the particular queue.Its value ranges between 1 and the value of axsEtherTxQoSStatsMaxQnum." ::= { axsEtherTxQoSStatsQueueEntry 2 } axsEtherTxQoSStatsQueueQlen OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A length of outbound priority queue for a interface." ::= { axsEtherTxQoSStatsQueueEntry 3 } axsEtherTxQoSStatsQueueMaxQlen OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max length of outbound priority queue for a interface since system was up." ::= { axsEtherTxQoSStatsQueueEntry 4 } axsEtherTxQoSStatsQueueDiscardFramesClass1 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discard frames in the discard class 1 of output priority queue." ::= { axsEtherTxQoSStatsQueueEntry 5 } axsEtherTxQoSStatsQueueDiscardFramesClass2 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discard frames in the discard class 2 of output priority queue." ::= { axsEtherTxQoSStatsQueueEntry 6 } axsEtherTxQoSStatsQueueDiscardFramesClass3 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discard frames in the discard class 3 of output priority queue." ::= { axsEtherTxQoSStatsQueueEntry 7 } axsEtherTxQoSStatsQueueDiscardFramesClass4 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discard frames in the discard class 4 of output priority queue." ::= { axsEtherTxQoSStatsQueueEntry 8 } axsToCpuQoSStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsToCpuQoSStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table information on the QoS statistics about the sending queue for cpu." ::= { axsToCpuQoS 1 } axsToCpuQoSStatsEntry OBJECT-TYPE SYNTAX AxsToCpuQoSStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry concerning corresponding QoS statistics about the sending queue for cpu." INDEX { axsToCpuQoSStatsIndex } ::= { axsToCpuQoSStatsTable 1 } AxsToCpuQoSStatsEntry ::= SEQUENCE { axsToCpuQoSStatsIndex INTEGER, axsToCpuQoSStatsMaxQnum INTEGER, axsToCpuQoSStatsLimitQlen INTEGER, axsToCpuQoSStatsTotalOutFrames Counter, axsToCpuQoSStatsTotalOutBytesHigh Counter, axsToCpuQoSStatsTotalOutBytesLow Counter, axsToCpuQoSStatsTotalDiscardFrames Counter } axsToCpuQoSStatsIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The number in the part in which the sending queue for cpu exists." ::= { axsToCpuQoSStatsEntry 1 } axsToCpuQoSStatsMaxQnum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of queues of the sending queue for cpu." ::= { axsToCpuQoSStatsEntry 2 } axsToCpuQoSStatsLimitQlen OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The limit length of the priority queue of the sending queue for cpu." ::= { axsToCpuQoSStatsEntry 3 } axsToCpuQoSStatsTotalOutFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of sent frames of the sending queue for cpu." ::= { axsToCpuQoSStatsEntry 4 } axsToCpuQoSStatsTotalOutBytesHigh OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of sent bytes (the high order 4-bytes) of the sending queue for cpu." ::= { axsToCpuQoSStatsEntry 5 } axsToCpuQoSStatsTotalOutBytesLow OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of sent bytes (the low order 4-bytes) of the sending queue for cpu." ::= { axsToCpuQoSStatsEntry 6 } axsToCpuQoSStatsTotalDiscardFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of discarded frames of the sending queue for cpu." ::= { axsToCpuQoSStatsEntry 7 } axsToCpuQoSStatsQueueTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsToCpuQoSStatsQueueEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table information on the QoS statistics of priority queue about the sending queue for cpu." ::= { axsToCpuQoS 2 } axsToCpuQoSStatsQueueEntry OBJECT-TYPE SYNTAX AxsToCpuQoSStatsQueueEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry concerning corresponding QoS statistics of priority queue about the sending queue for cpu." INDEX { axsToCpuQoSStatsQueueIndex, axsToCpuQoSStatsQueueQueIndex } ::= { axsToCpuQoSStatsQueueTable 1 } AxsToCpuQoSStatsQueueEntry ::= SEQUENCE { axsToCpuQoSStatsQueueIndex INTEGER, axsToCpuQoSStatsQueueQueIndex INTEGER, axsToCpuQoSStatsQueueQlen INTEGER, axsToCpuQoSStatsQueueMaxQlen INTEGER, axsToCpuQoSStatsQueueDiscardFramesClass1 Counter64, axsToCpuQoSStatsQueueDiscardFramesClass2 Counter64, axsToCpuQoSStatsQueueDiscardFramesClass3 Counter64, axsToCpuQoSStatsQueueDiscardFramesClass4 Counter64 } axsToCpuQoSStatsQueueIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The number in the part in which the sending queue for cpu exists." ::= { axsToCpuQoSStatsQueueEntry 1 } axsToCpuQoSStatsQueueQueIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The index value which identifies the entry of this table. Values between 1 and axsToCpuQoSStatsMaxQnum." ::= { axsToCpuQoSStatsQueueEntry 2 } axsToCpuQoSStatsQueueQlen OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A length of priority queue about the sending queue for cpu." ::= { axsToCpuQoSStatsQueueEntry 3 } axsToCpuQoSStatsQueueMaxQlen OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The highest queue length of priority queue about the sending queue for cpu after being cleared or initialized." ::= { axsToCpuQoSStatsQueueEntry 4 } axsToCpuQoSStatsQueueDiscardFramesClass1 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discarded frames in the discard class 1 of priority queue about the sending queue for cpu." ::= { axsToCpuQoSStatsQueueEntry 5 } axsToCpuQoSStatsQueueDiscardFramesClass2 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discarded frames in the discard class 2 of priority queue about the sending queue for cpu." ::= { axsToCpuQoSStatsQueueEntry 6 } axsToCpuQoSStatsQueueDiscardFramesClass3 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discarded frames in the discard class 3 of priority queue about the sending queue for cpu." ::= { axsToCpuQoSStatsQueueEntry 7 } axsToCpuQoSStatsQueueDiscardFramesClass4 OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The number of discarded frames in the discard class 4 of priority queue about the sending queue for cpu." ::= { axsToCpuQoSStatsQueueEntry 8 } --axsDHCP group Variables axsDHCPAddrValue OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP addresses which are available within this Router." ::= { axsDHCP 1 } axsDHCPFreeAddrValue OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP addresses which are available within this Router. May be expressed as either an absolute value." ::= { axsDHCP 2 } -- axsGsrp Group axsGsrpGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsGsrpGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing GSRP group information." ::= { axsGsrp 1 } axsGsrpGroupEntry OBJECT-TYPE SYNTAX AxsGsrpGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The list of GSRP group information." INDEX { axsGsrpGroupId } ::= { axsGsrpGroupTable 1 } AxsGsrpGroupEntry ::= SEQUENCE { axsGsrpGroupId INTEGER, axsGsrpGroupRowStatus RowStatus, axsGsrpMacAddress MacAddress, axsGsrpAdvertiseHoldTime INTEGER, axsGsrpAdvertiseInterval INTEGER, axsGsrpSelectionPattern INTEGER, axsGsrpLayer3Redundancy INTEGER } axsGsrpGroupId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "GSRP group identifier." ::= { axsGsrpGroupEntry 1 } axsGsrpGroupRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "Valid/Invalid state of this entry. Valid(1) fixed" ::= { axsGsrpGroupEntry 2 } axsGsrpMacAddress OBJECT-TYPE SYNTAX MacAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Media Access Control Address of this equipment." ::= { axsGsrpGroupEntry 3 } axsGsrpAdvertiseHoldTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Holding time of the Advertise frame (milli second)." ::= { axsGsrpGroupEntry 4 } axsGsrpAdvertiseInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interval between transmitting the Advertise frame (milli second)." ::= { axsGsrpGroupEntry 5 } axsGsrpSelectionPattern OBJECT-TYPE SYNTAX INTEGER { ports-Priority-MAC(1), priority-Ports-MAC(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Master/Backup selection pattern. Ports-Priority-MAC(1) Priority-Ports-MAC(2)" ::= { axsGsrpGroupEntry 6 } axsGsrpLayer3Redundancy OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of layer 3 redundancy-change." ::= { axsGsrpGroupEntry 7 } axsGsrpVlanGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsGsrpVlanGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing GSRP VLAN group information." ::= { axsGsrp 2 } axsGsrpVlanGroupEntry OBJECT-TYPE SYNTAX AxsGsrpVlanGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The list of GSRP VLAN group information." INDEX { axsGsrpGroupId, axsGsrpVlanGroupId } ::= { axsGsrpVlanGroupTable 1 } AxsGsrpVlanGroupEntry ::= SEQUENCE { axsGsrpVlanGroupId INTEGER, axsGsrpVlanGroupRowStatus RowStatus, axsGsrpState INTEGER, axsGsrpPriority INTEGER, axsGsrpActivePorts INTEGER, axsGsrpTransitionToMasterCounts INTEGER, axsGsrpTransitionFromMasterCounts INTEGER, axsGsrpLastTransitionTime TimeStamp, axsGsrpVirtualMacAddress MacAddress } axsGsrpVlanGroupId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "GSRP VLAN group number(1~8)" ::= { axsGsrpVlanGroupEntry 1 } axsGsrpVlanGroupRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "Valid/Invalid state of this entry. Valid(1) fixed" ::= { axsGsrpVlanGroupEntry 2 } axsGsrpState OBJECT-TYPE SYNTAX INTEGER { backUp(1), backUp-Waiting(2), master(3), backUp-No-Neighbor(4), backUp-Lock(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of GSRP group." ::= { axsGsrpVlanGroupEntry 3 } axsGsrpPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Configured priority." ::= { axsGsrpVlanGroupEntry 4 } axsGsrpActivePorts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of port which is link-up in monitored port." ::= { axsGsrpVlanGroupEntry 5 } axsGsrpTransitionToMasterCounts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of times which shifted to the master state from the backup state." ::= { axsGsrpVlanGroupEntry 6 } axsGsrpTransitionFromMasterCounts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of times which shifted to the backup state from the master state." ::= { axsGsrpVlanGroupEntry 7 } axsGsrpLastTransitionTime OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "The last time at which changed in the master state from the backup state or in the backup state from the master state." ::= { axsGsrpVlanGroupEntry 8 } axsGsrpVirtualMacAddress OBJECT-TYPE SYNTAX MacAddress ACCESS read-only STATUS mandatory DESCRIPTION "The virtual Media Access Control address of the GSRP VLAN group. If the status of layer 3 redundancy-change is off, return 00 00 00 00 00 00" ::= { axsGsrpVlanGroupEntry 9 } axsGsrpNeighborGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsGsrpNeighborGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing stores the GSRP group information on facing equipment." ::= { axsGsrp 3 } axsGsrpNeighborGroupEntry OBJECT-TYPE SYNTAX AxsGsrpNeighborGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing stores the GSRP group information on facing equipment." INDEX { axsGsrpNeighborGroupId, axsGsrpNeighborMacAddress } ::= { axsGsrpNeighborGroupTable 1 } AxsGsrpNeighborGroupEntry ::= SEQUENCE { axsGsrpNeighborGroupId INTEGER, axsGsrpNeighborMacAddress MacAddress, axsGsrpNeighborAdvertiseHoldTime INTEGER, axsGsrpNeighborAdvertiseInterval INTEGER, axsGsrpNeighborSelectionPattern INTEGER } axsGsrpNeighborGroupId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The GSRP group identifier on the facing equipment." ::= { axsGsrpNeighborGroupEntry 1 } axsGsrpNeighborMacAddress OBJECT-TYPE SYNTAX MacAddress ACCESS not-accessible STATUS mandatory DESCRIPTION "The Media Access Control Address of the facing equipment." ::= { axsGsrpNeighborGroupEntry 2 } axsGsrpNeighborAdvertiseHoldTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Holding time of the Advertise frame on opposite equipment (milli second)." ::= { axsGsrpNeighborGroupEntry 3 } axsGsrpNeighborAdvertiseInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Interval between transmitting the Advertise frame on the facing equipment (milli second)." ::= { axsGsrpNeighborGroupEntry 4 } axsGsrpNeighborSelectionPattern OBJECT-TYPE SYNTAX INTEGER { port-Priority-MAC(1), priority-Port-MAC(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Master/Backup selection pattern on the facing equipment. Ports-Priority-MAC(1) Priority-Ports-MAC(2)" ::= { axsGsrpNeighborGroupEntry 5 } axsGsrpNeighborVlanGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsGsrpNeighborVlanGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing the GSRP VLAN group information on facing equipment." ::= { axsGsrp 4 } axsGsrpNeighborVlanGroupEntry OBJECT-TYPE SYNTAX AxsGsrpNeighborVlanGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing the GSRP VLAN group information on facing equipment." INDEX { axsGsrpNeighborGroupId, axsGsrpNeighborVlanGroupId, axsGsrpNeighborMacAddress } ::= { axsGsrpNeighborVlanGroupTable 1 } AxsGsrpNeighborVlanGroupEntry ::= SEQUENCE { axsGsrpNeighborVlanGroupId INTEGER, axsGsrpNeighborState INTEGER, axsGsrpNeighborPriority INTEGER, axsGsrpNeighborActivePorts INTEGER } axsGsrpNeighborVlanGroupId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "GSRP VLAN group number on the facing equipment (1~8)." ::= { axsGsrpNeighborVlanGroupEntry 1 } axsGsrpNeighborState OBJECT-TYPE SYNTAX INTEGER { backUp(1), backUp-Waiting(2), master(3), backUp-No-Neighbor(4), backUp-Lock(5) } ACCESS not-accessible STATUS mandatory DESCRIPTION "The state of GSRP group on the facing equipment." ::= { axsGsrpNeighborVlanGroupEntry 2 } axsGsrpNeighborPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Configured priority on the facing equipment." ::= { axsGsrpNeighborVlanGroupEntry 3 } axsGsrpNeighborActivePorts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of port which is link-up in monitored port on the facing equipment." ::= { axsGsrpNeighborVlanGroupEntry 4 } -- axsFdb group axsFdbCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsFdbCounterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of FDB information." ::= { axsFdb 1 } axsFdbCounterEntry OBJECT-TYPE SYNTAX AxsFdbCounterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of FDB information." INDEX { axsFdbCounterNifIndex, axsFdbCounterLineIndex } ::= { axsFdbCounterTable 1 } AxsFdbCounterEntry ::= SEQUENCE { axsFdbCounterNifIndex INTEGER, axsFdbCounterLineIndex INTEGER, axsFdbCounterCounts Counter32, axsFdbCounterType INTEGER, axsFdbCounterLimits Counter32 } axsFdbCounterNifIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Identified by a particular value of this index is same value of NIF.Its value ranges between 1 and the value of ax3630sNifBoardNumber." ::= { axsFdbCounterEntry 1 } axsFdbCounterLineIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Identified by a particular value of this index is same value of Physical Line.Its value ranges between 1 and the value of ax3630sNifLineNumber." ::= { axsFdbCounterEntry 2 } axsFdbCounterCounts OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of FDB entries learned on the port." ::= { axsFdbCounterEntry 3 } axsFdbCounterType OBJECT-TYPE SYNTAX INTEGER { unlimited(0), limited-and-Forward(1), limited-and-Discard(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of FDB entries learning." ::= { axsFdbCounterEntry 4 } axsFdbCounterLimits OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of FDB entries that can be learned on the port." ::= { axsFdbCounterEntry 5 } -- axsVlan group axsVBBaseTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBBaseEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information table of dot1dBase by VLAN units." ::= { axsVlanBridgeBase 1 } axsVBBaseEntry OBJECT-TYPE SYNTAX AxsVBBaseEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information entry of every VLAN ID of axsVBBaseTable." INDEX { axsVBBaseIndex } ::= { axsVBBaseTable 1 } AxsVBBaseEntry ::= SEQUENCE { axsVBBaseIndex VlanIndex, axsVBBaseBridgeAddress MacAddress, axsVBBaseNumPorts INTEGER, axsVBBaseType INTEGER, axsVBBaseVlanIfIndex INTEGER, axsVBBaseVlanType INTEGER, axsVBBaseVlanID VlanIdOrZero, axsVBBaseAssociatedPrimaryVlan VlanIdOrZero, axsVBBaseIfStatus INTEGER, axsVBBaseLastChange TimeTicks, axsVBBasePrivateVlanType INTEGER } axsVBBaseIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBBaseEntry 1 } axsVBBaseBridgeAddress OBJECT-TYPE SYNTAX MacAddress ACCESS read-only STATUS mandatory DESCRIPTION "MAC address of VLAN." ::= { axsVBBaseEntry 2 } axsVBBaseNumPorts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of ports set at VLAN." ::= { axsVBBaseEntry 3 } axsVBBaseType OBJECT-TYPE SYNTAX INTEGER { unknown(1), transparent-only(2), sourceroute-only(3), srt(4) } ACCESS read-only STATUS mandatory DESCRIPTION "A bridging type VLAN may perform." ::= { axsVBBaseEntry 4 } axsVBBaseVlanIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of ifIndex of interface of VLAN." ::= { axsVBBaseEntry 5 } axsVBBaseVlanType OBJECT-TYPE SYNTAX INTEGER { port-based(1), mac-based(2), protocol-based(3), ipsubnet-based(4) } ACCESS read-only STATUS mandatory DESCRIPTION "VLAN type." ::= { axsVBBaseEntry 6 } axsVBBaseVlanID OBJECT-TYPE SYNTAX VlanIdOrZero ACCESS read-only STATUS mandatory DESCRIPTION "Value of VID of VLAN-TAG corresponding VLAN." ::= { axsVBBaseEntry 7 } axsVBBaseAssociatedPrimaryVlan OBJECT-TYPE SYNTAX VlanIdOrZero ACCESS read-only STATUS mandatory DESCRIPTION "Returns VLAN ID of Primary VLAN when private VLAN is used and the same VLAN is set at secondary VLAN." ::= { axsVBBaseEntry 8 } axsVBBaseIfStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of interface against upper level protocol of VLAN." ::= { axsVBBaseEntry 9 } axsVBBaseLastChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Value of sysUpTime which is set when VLAN topology changes." ::= { axsVBBaseEntry 10 } axsVBBasePrivateVlanType OBJECT-TYPE SYNTAX INTEGER { normal(1), primary(2), isolated(3), community(4) } ACCESS read-only STATUS mandatory DESCRIPTION "A private VLAN type of VLAN." ::= { axsVBBaseEntry 11 } axsVBBasePortTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBBasePortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information table of dot1dBasePortTable by VLAN units." ::= { axsVlanBridgeBase 2 } axsVBBasePortEntry OBJECT-TYPE SYNTAX AxsVBBasePortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A configuration entry of axsVBBaseTable." INDEX { axsVBBasePortIndex, axsVBBasePort } ::= { axsVBBasePortTable 1 } AxsVBBasePortEntry ::= SEQUENCE { axsVBBasePortIndex VlanIndex, axsVBBasePort INTEGER, axsVBBasePortIfIndex INTEGER, axsVBBasePortCircuit OBJECT IDENTIFIER, axsVBBasePortDelayExceededDiscards Counter, axsVBBasePortMtuExceededDiscards Counter, axsVBBasePortState INTEGER, axsVBBasePortTaggedState INTEGER, axsVBBasePortTranslatedTagID VlanIdOrZero } axsVBBasePortIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBBasePortEntry 1 } axsVBBasePort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Port number of ports set at VLAN." ::= { axsVBBasePortEntry 2 } axsVBBasePortIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value of ifIndex corresponding ports set at VLAN." ::= { axsVBBasePortEntry 3 } axsVBBasePortCircuit OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "Identifier which identifieds ports when VLAN ports have the same value as axsVBBasePortIfIndex." ::= { axsVBBasePortEntry 4 } axsVBBasePortDelayExceededDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of discard frame caused by passing delay occured at VLAN ports." ::= { axsVBBasePortEntry 5 } axsVBBasePortMtuExceededDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of discard frame caused by data over flow occured at VLAN ports." ::= { axsVBBasePortEntry 6 } axsVBBasePortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6), fix-forwarding(7) } ACCESS read-only STATUS mandatory DESCRIPTION "STP port status of port set at VLAN." ::= { axsVBBasePortEntry 7 } axsVBBasePortTaggedState OBJECT-TYPE SYNTAX INTEGER { untagged(1), tagged(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of VLAN-TAG configuration of ports set at VLAN." ::= { axsVBBasePortEntry 8 } axsVBBasePortTranslatedTagID OBJECT-TYPE SYNTAX VlanIdOrZero ACCESS read-only STATUS mandatory DESCRIPTION "Translated ID of VLAN when TAG translation is set." ::= { axsVBBasePortEntry 9 } axsVBStpTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBStpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information table of dot1dStpTable by VLAN units." ::= { axsVlanBridgeStp 1 } axsVBStpEntry OBJECT-TYPE SYNTAX AxsVBStpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A configuration entry of axsVBStpTable." INDEX { axsVBStpIndex } ::= { axsVBStpTable 1 } AxsVBStpEntry ::= SEQUENCE { axsVBStpIndex VlanIndex, axsVBStpProtocolSpecification INTEGER, axsVBStpPriority INTEGER, axsVBStpTimeSinceTopologyChange TimeTicks, axsVBStpTopChanges Counter, axsVBStpDesignatedRoot BridgeId, axsVBStpRootCost INTEGER, axsVBStpRootPort INTEGER, axsVBStpMaxAge Timeout, axsVBStpHelloTime Timeout, axsVBStpHoldTime INTEGER, axsVBStpForwardDelay Timeout, axsVBStpBridgeMaxAge Timeout, axsVBStpBridgeHelloTime Timeout, axsVBStpBridgeForwardDelay Timeout } axsVBStpIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBStpEntry 1 } axsVBStpProtocolSpecification OBJECT-TYPE SYNTAX INTEGER { unknown(1), decLb100(2), ieee8021d(3), ieee8021w(4) } ACCESS read-only STATUS mandatory DESCRIPTION "A kind of spanning tree protocol by VLAN units." ::= { axsVBStpEntry 2 } axsVBStpPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Priority value of spanning tree by VLAN units." ::= { axsVBStpEntry 3 } axsVBStpTimeSinceTopologyChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Elapsed time since topology change of spanning tree by VLAN units." ::= { axsVBStpEntry 4 } axsVBStpTopChanges OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times of topology changes of spanning tree by VLAN units." ::= { axsVBStpEntry 5 } axsVBStpDesignatedRoot OBJECT-TYPE SYNTAX BridgeId ACCESS read-only STATUS mandatory DESCRIPTION "Root bridge identifier of spanning tree by VLAN units." ::= { axsVBStpEntry 6 } axsVBStpRootCost OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Root path cost kept by spanning tree by VLAN units." ::= { axsVBStpEntry 7 } axsVBStpRootPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Root port value kept by spanning tree by VLAN units." ::= { axsVBStpEntry 8 } axsVBStpMaxAge OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "Maximum aging time kept by spanning tree by VLAN units." ::= { axsVBStpEntry 9 } axsVBStpHelloTime OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "Hello time kept by spanning tree by VLAN units." ::= { axsVBStpEntry 10 } axsVBStpHoldTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Hold time kept by spanning tree by VLAN units." ::= { axsVBStpEntry 11 } axsVBStpForwardDelay OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "Transfer delay time kept by spanning tree by VLAN units." ::= { axsVBStpEntry 12 } axsVBStpBridgeMaxAge OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "Maximum aging time used when spanning tree acts as a root bridge by VLAN units." ::= { axsVBStpEntry 13 } axsVBStpBridgeHelloTime OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "Hello time used when spanning tree act as a root bridge by VLAN units." ::= { axsVBStpEntry 14 } axsVBStpBridgeForwardDelay OBJECT-TYPE SYNTAX Timeout ACCESS read-only STATUS mandatory DESCRIPTION "Transfer delay time used when spanning tree act as a root bridge by VLAN units." ::= { axsVBStpEntry 15 } axsVBStpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBStpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information table of dot1dStpPortTable by VLAN units." ::= { axsVlanBridgeStp 2 } axsVBStpPortEntry OBJECT-TYPE SYNTAX AxsVBStpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A configuration entry of axsVBStpPortTable." INDEX { axsVBStpPortIndex, axsVBStpPort } ::= { axsVBStpPortTable 1 } AxsVBStpPortEntry ::= SEQUENCE { axsVBStpPortIndex VlanIndex, axsVBStpPort INTEGER, axsVBStpPortPriority INTEGER, axsVBStpPortState INTEGER, axsVBStpPortEnable INTEGER, axsVBStpPortPathCost INTEGER, axsVBStpPortDesignatedRoot BridgeId, axsVBStpPortDesignatedCost INTEGER, axsVBStpPortDesignatedBridge BridgeId, axsVBStpPortDesignatedPort OCTET STRING, axsVBStpPortForwardTransitions Counter } axsVBStpPortIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBStpPortEntry 1 } axsVBStpPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Port number corresponding configuration entry." ::= { axsVBStpPortEntry 2 } axsVBStpPortPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Priority of port by VLAN units." ::= { axsVBStpPortEntry 3 } axsVBStpPortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Present status of port by VLAN units." ::= { axsVBStpPortEntry 4 } axsVBStpPortEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Value whether spanning tree is enabled or not at the port by VLAN units." ::= { axsVBStpPortEntry 5 } axsVBStpPortPathCost OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Path cost value of the port by VLAN units." ::= { axsVBStpPortEntry 6 } axsVBStpPortDesignatedRoot OBJECT-TYPE SYNTAX BridgeId ACCESS read-only STATUS mandatory DESCRIPTION "Value of root bridge identifier by VLAN units stored in BPDU from specified bridge." ::= { axsVBStpPortEntry 7 } axsVBStpPortDesignatedCost OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Path cost value of specified port connected to the port by VLAN units." ::= { axsVBStpPortEntry 8 } axsVBStpPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId ACCESS read-only STATUS mandatory DESCRIPTION "Bridge identifier of bridge which this port regards as specified bridge by VLAN units." ::= { axsVBStpPortEntry 9 } axsVBStpPortDesignatedPort OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Port identifier of specified bridge connected to this port by VLAN units." ::= { axsVBStpPortEntry 10 } axsVBStpPortForwardTransitions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times of changes from learning status into forwarding status." ::= { axsVBStpPortEntry 11 } axsVBTpTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBTpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A dot1dTp information table by VLAN units." ::= { axsVlanBridgeTp 1 } axsVBTpEntry OBJECT-TYPE SYNTAX AxsVBTpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A configuration entry of axsVBTpTable." INDEX { axsVBTpIndex } ::= { axsVBTpTable 1 } AxsVBTpEntry ::= SEQUENCE { axsVBTpIndex VlanIndex, axsVBTpLearnedEntryDiscards Counter, axsVBTpAgingTime INTEGER } axsVBTpIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBTpEntry 1 } axsVBTpLearnedEntryDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of discarded entries because of lack of not-used domain in filtering data base." ::= { axsVBTpEntry 2 } axsVBTpAgingTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Time-out time to aging-out entry of filtering date base which is learned dynamically." ::= { axsVBTpEntry 3 } axsVBTpFdbTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBTpFdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information of dot1dTpFdbTable by VLAN units." ::= { axsVlanBridgeTp 2 } axsVBTpFdbEntry OBJECT-TYPE SYNTAX AxsVBTpFdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A configuration entry of axsVBTpFdbTable." INDEX { axsVBTpFdbIndex, axsVBTpFdbAddress } ::= { axsVBTpFdbTable 1 } AxsVBTpFdbEntry ::= SEQUENCE { axsVBTpFdbIndex VlanIndex, axsVBTpFdbAddress MacAddress, axsVBTpFdbPort INTEGER, axsVBTpFdbStatus INTEGER } axsVBTpFdbIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBTpFdbEntry 1 } axsVBTpFdbAddress OBJECT-TYPE SYNTAX MacAddress ACCESS read-only STATUS mandatory DESCRIPTION "Unicast MAC address of filtering data base entry." ::= { axsVBTpFdbEntry 2 } axsVBTpFdbPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Indicates that it hasn't learnt port number when port number 0 receives frame having MAC address as source address which axsVBTpFdbAddress indicates." ::= { axsVBTpFdbEntry 3 } axsVBTpFdbStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), learned(3), self(4), mgmt(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of filtering data base." ::= { axsVBTpFdbEntry 4 } axsVBTpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBTpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information table of dot1dTpPortTable by VLAN units." ::= { axsVlanBridgeTp 3 } axsVBTpPortEntry OBJECT-TYPE SYNTAX AxsVBTpPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information entry of axsVBTpPortTable of ports." INDEX { axsVBTpPortIndex, axsVBTpPort } ::= { axsVBTpPortTable 1 } AxsVBTpPortEntry ::= SEQUENCE { axsVBTpPortIndex VlanIndex, axsVBTpPort INTEGER, axsVBTpPortMaxInfo INTEGER, axsVBTpPortInFrames Counter, axsVBTpPortOutFrames Counter, axsVBTpPortInDiscards Counter } axsVBTpPortIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBTpPortEntry 1 } axsVBTpPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Port number that indicates which port management information in the entry corresponds." ::= { axsVBTpPortEntry 2 } axsVBTpPortMaxInfo OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Maximum INFO field size of the port by VLAN units." ::= { axsVBTpPortEntry 3 } axsVBTpPortInFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of reception frame of the port by VLAN units." ::= { axsVBTpPortEntry 4 } axsVBTpPortOutFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of sending frame of the port by VLAN units." ::= { axsVBTpPortEntry 5 } axsVBTpPortInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of reception frame of the port by VLAN units." ::= { axsVBTpPortEntry 6 } axsVBStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVBStaticEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An information table of dot1dStaticTable by VLAN units." ::= { axsVlanBridgeStatic 1 } axsVBStaticEntry OBJECT-TYPE SYNTAX AxsVBStaticEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A configuration entry of axsVBStaticTable." INDEX { axsVBStaticIndex, axsVBStaticAddress } ::= { axsVBStaticTable 1 } AxsVBStaticEntry ::= SEQUENCE { axsVBStaticIndex VlanIndex, axsVBStaticAddress MacAddress, axsVBStaticReceivePort INTEGER, axsVBStaticAllowedToGoTo OCTET STRING, axsVBStaticStatus INTEGER } axsVBStaticIndex OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID." ::= { axsVBStaticEntry 1 } axsVBStaticAddress OBJECT-TYPE SYNTAX MacAddress ACCESS read-only STATUS mandatory DESCRIPTION "MAC address of eather unicast, group or broadcast." ::= { axsVBStaticEntry 2 } axsVBStaticReceivePort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Reception port number which is applied the entry." ::= { axsVBStaticEntry 3 } axsVBStaticAllowedToGoTo OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Bit map of port indicating destination port when transfering frame whose destination is MAC address kept by this entry" ::= { axsVBStaticEntry 4 } axsVBStaticStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of the entry." ::= { axsVBStaticEntry 5 } axsVlanBridgeMaxVlans OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "Maximum value of VLAN ID of this device." ::= { axsVlanBridge 101 } axsVlanBridgeMaxSpans OBJECT-TYPE SYNTAX VlanIndex ACCESS read-only STATUS mandatory DESCRIPTION "Maximum value of VLAN ID of VLAN which may operate spanning tree in this device." ::= { axsVlanBridge 102 } axsVlanTagTranslationTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVlanTagTranslationEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The information table about a Tag conversion function" ::= { axsVlanTagTranslation 1 } axsVlanTagTranslationEntry OBJECT-TYPE SYNTAX AxsVlanTagTranslationEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of the information table about a Tag conversion function" INDEX { axsVlanTagTranslationVlanId,axsVlanTagTranslationTranslatedId } ::= { axsVlanTagTranslationTable 1 } AxsVlanTagTranslationEntry ::= SEQUENCE { axsVlanTagTranslationVlanId INTEGER, axsVlanTagTranslationTranslatedId INTEGER, axsVlanTagTranslationPorts PortList } axsVlanTagTranslationVlanId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "VLAN ID which has set up the Tag conversion function" ::= { axsVlanTagTranslationEntry 1 } axsVlanTagTranslationTranslatedId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Translated ID set up by the Tag conversion function" ::= { axsVlanTagTranslationEntry 2 } axsVlanTagTranslationPorts OBJECT-TYPE SYNTAX PortList ACCESS read-only STATUS mandatory DESCRIPTION "The port list which has set up the same Translated ID by the same VLAN by the Tag conversion function" ::= { axsVlanTagTranslationEntry 3 } -- OADP Group axsOadpGlobalActive OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Operation status of OADP function. Status set by enable or disable in Oadp configuration. enable : 1 disable: 2" ::= { axsOadpGlobalInfo 1 } axsOadpGlobalCdpActive OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Operation status of CDP reception function. Status whether cdp-listener is set or not in oadp configuration. cdp-listener : 1 cdp-listener is not set: 2" ::= { axsOadpGlobalInfo 2 } axsOadpGlobalMessageInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Sending interval of OADP frame. The value of interval-time in oadp configuration." ::= { axsOadpGlobalInfo 3 } axsOadpGlobalHoldTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Neighbor divice's holding time of OADP frame which this device send. The value of hold-time in oadp configuration." ::= { axsOadpGlobalInfo 4 } axsOadpGlobalCacheLastChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Value of sysUpTime which is set when axsOadpNeighborTable is updated." ::= { axsOadpGlobalInfo 5 } axsOadpGlobalName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Device identifier." ::= { axsOadpGlobalInfo 6 } axsOadpGlobalNameType OBJECT-TYPE SYNTAX INTEGER { other(1), sysName(2), serialNumber(3), macaddress(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Kind of axsOadpGlobalName." ::= { axsOadpGlobalInfo 7 } axsOadpPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOadpPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of OADP port information." ::= { axsOadpPortInfo 1 } axsOadpPortConfigEntry OBJECT-TYPE SYNTAX AxsOadpPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry of OADP port information." INDEX { axsOadpPortConfigIfIndex } ::= { axsOadpPortConfigTable 1 } AxsOadpPortConfigEntry ::= SEQUENCE { axsOadpPortConfigIfIndex InterfaceIndex, axsOadpPortConfigActive TruthValue } axsOadpPortConfigIfIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "Port identification index. The same value as ifIndex. This is only for physical ports and LA ports which are given ifIndex." ::= { axsOadpPortConfigEntry 1 } axsOadpPortConfigActive OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Status of specified port." ::= { axsOadpPortConfigEntry 2 } axsOadpNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOadpNeighborEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of OADP neighbor nodes." ::= { axsOadpNeighborInfo 1 } axsOadpNeighborEntry OBJECT-TYPE SYNTAX AxsOadpNeighborEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry of OADP neighbor nodes." INDEX { axsOadpIfIndex, axsOadpTagID, axsOadpNeighborIndex, axsOadpNeighborTagID } ::= { axsOadpNeighborTable 1 } AxsOadpNeighborEntry ::= SEQUENCE { axsOadpIfIndex InterfaceIndex, axsOadpTagID INTEGER, axsOadpNeighborIndex INTEGER, axsOadpNeighborTagID INTEGER, axsOadpNeighborVendorType INTEGER, axsOadpNeighborSNMPAgentAddressType INTEGER, axsOadpNeighborSNMPAgentAddress DisplayString, axsOadpNeighborDescr DisplayString, axsOadpNeighborDeviceID DisplayString, axsOadpNeighborSlotPort DisplayString, axsOadpNeighborIfIndex InterfaceIndex, axsOadpNeighborIfSpeed Gauge, axsOadpNeighborDeviceType DisplayString, axsOadpNeighborService OCTET STRING, axsOadpNeighborVTPMgmtDomain DisplayString, axsOadpNeighborNativeVLAN INTEGER, axsOadpNeighborDuplex INTEGER, axsOadpNeighborApplianceID Gauge, axsOadpNeighborVlanID Gauge, axsOadpNeighborPowerConsumption Gauge, axsOadpNeighborMTU Gauge, axsOadpNeighborSysName DisplayString, axsOadpNeighborSysObjectID OBJECT IDENTIFIER, axsOadpNeighborSecondarySNMPAgentAddressType INTEGER, axsOadpNeighborSecondarySNMPAgentAddress DisplayString, axsOadpNeighborPhysLocation DisplayString, axsOadpNeighborCacheLastChange TimeTicks, axsOadpNeighborIfHighSpeed Gauge } axsOadpIfIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "ifIndex of reception interface." ::= { axsOadpNeighborEntry 1 } axsOadpTagID OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Tag ID of IEEE802.1Q which is attached MAC frame." ::= { axsOadpNeighborEntry 2 } axsOadpNeighborIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Unique numeric which identifies neighbor nodes" ::= { axsOadpNeighborEntry 3 } axsOadpNeighborTagID OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Value set at TagID TLV in OADP PDU which is sent from neighbor node." ::= { axsOadpNeighborEntry 4 } axsOadpNeighborVendorType OBJECT-TYPE SYNTAX INTEGER { other(1), oadp(2), cdp(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Protocol type used to find to neighbor nodes." ::= { axsOadpNeighborEntry 5 } axsOadpNeighborSNMPAgentAddressType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(20), other-notSupported(65535) } ACCESS read-only STATUS mandatory DESCRIPTION "A kind of agent address to get information by SNMP." ::= { axsOadpNeighborEntry 6 } axsOadpNeighborSNMPAgentAddress OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "DisplayString formed information of agent address to get information by SNMP." ::= { axsOadpNeighborEntry 7 } axsOadpNeighborDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "String of sysDescr of neighbor node." ::= { axsOadpNeighborEntry 8 } axsOadpNeighborDeviceID OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Neighbor node's device identifier." ::= { axsOadpNeighborEntry 9 } axsOadpNeighborSlotPort OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Unique string which identifies neighbor's sending interface." ::= { axsOadpNeighborEntry 10 } axsOadpNeighborIfIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "ifIndex of sending interface of neighbor node." ::= { axsOadpNeighborEntry 11 } axsOadpNeighborIfSpeed OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "ifSpeed of sending interface of neighbor node." ::= { axsOadpNeighborEntry 12 } axsOadpNeighborDeviceType OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Device name of neighbor node." ::= { axsOadpNeighborEntry 13 } axsOadpNeighborService OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Functions neighbor node can offer." ::= { axsOadpNeighborEntry 14 } axsOadpNeighborVTPMgmtDomain OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "VTP Management Domain of sending interface of neighbor node." ::= { axsOadpNeighborEntry 15 } axsOadpNeighborNativeVLAN OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Native VLAN number of sending interface of neighbor node." ::= { axsOadpNeighborEntry 16 } axsOadpNeighborDuplex OBJECT-TYPE SYNTAX INTEGER { unknown(1), half(2), full(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Duplex information of sending interface of neighbor node." ::= { axsOadpNeighborEntry 17 } axsOadpNeighborApplianceID OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Appliance ID of neighbor node." ::= { axsOadpNeighborEntry 18 } axsOadpNeighborVlanID OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID for VoIP of neighbor node." ::= { axsOadpNeighborEntry 19 } axsOadpNeighborPowerConsumption OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "Electric power comsumption of neighbor node." ::= { axsOadpNeighborEntry 20 } axsOadpNeighborMTU OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "MTU of sending interface of neighbor node." ::= { axsOadpNeighborEntry 21 } axsOadpNeighborSysName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "sysName of neighbor node." ::= { axsOadpNeighborEntry 22 } axsOadpNeighborSysObjectID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "sysObjectID of neighbor node." ::= { axsOadpNeighborEntry 23 } axsOadpNeighborSecondarySNMPAgentAddressType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(20), other-notSupported(65535) } ACCESS read-only STATUS mandatory DESCRIPTION "A kind of agent secondary address to get information by SNMP." ::= { axsOadpNeighborEntry 24 } axsOadpNeighborSecondarySNMPAgentAddress OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "DisplayString formed information of agent secondary address to get information by SNMP." ::= { axsOadpNeighborEntry 25 } axsOadpNeighborPhysLocation OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "sysLocation of neighbor node." ::= { axsOadpNeighborEntry 26 } axsOadpNeighborCacheLastChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Value of sysUpTime which is set when axsOadpNeighborEntry about neighbor node is updated." ::= { axsOadpNeighborEntry 27 } axsOadpNeighborIfHighSpeed OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "ifHighSpeed of sending interface of neighbor node." ::= { axsOadpNeighborEntry 28 } -- axsFlow Group axsAccessFilterStatsInTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsAccessFilterStatsInEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table information on corresponding number of packets to flow detection condition and operation information set by access list." ::= { axsAccessFilterStats 1 } axsAccessFilterStatsInEntry OBJECT-TYPE SYNTAX AxsAccessFilterStatsInEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry concerning corresponding number of packets to flow detection condition and operation information set by access list." INDEX { axsAccessFilterStatsInifIndex, axsAccessFilterStatsInifIndexType, axsAccessFilterStatsInListIndex,axsAccessFilterStatsInSequenceNumber } ::= { axsAccessFilterStatsInTable 1 } AxsAccessFilterStatsInEntry ::= SEQUENCE { axsAccessFilterStatsInifIndex INTEGER, axsAccessFilterStatsInifIndexType INTEGER, axsAccessFilterStatsInListIndex Unsigned32, axsAccessFilterStatsInSequenceNumber Unsigned32, axsAccessFilterStatsInListName DisplayString, axsAccessFilterStatsInMatchedPackets Counter64 } axsAccessFilterStatsInifIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Index value in which entry of this table is identified." ::= { axsAccessFilterStatsInEntry 1 } axsAccessFilterStatsInifIndexType OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Indicates interface type. Physical port number : 1 Interface name : 2" ::= { axsAccessFilterStatsInEntry 2 } axsAccessFilterStatsInListIndex OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "Index value of access list that identifies entry of this table." ::= { axsAccessFilterStatsInEntry 3 } axsAccessFilterStatsInSequenceNumber OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "Sequence number of flow detection condition and operation information set to access list number or access list name. " ::= { axsAccessFilterStatsInEntry 4 } axsAccessFilterStatsInListName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Access list number or access list name corresponding to index of access list." ::= { axsAccessFilterStatsInEntry 5 } axsAccessFilterStatsInMatchedPackets OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Corresponding number of packets to flow detection condition of access list. " ::= { axsAccessFilterStatsInEntry 6 } axsAccessFilterStatsOutTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsAccessFilterStatsOutEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table information on corresponding number of packets to flow detection condition and operation information set by access list of Outbound." ::= { axsAccessFilterStats 2 } axsAccessFilterStatsOutEntry OBJECT-TYPE SYNTAX AxsAccessFilterStatsOutEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry concerning corresponding number of packets to flow detection condition and operation information set by access list of Outbound." INDEX { axsAccessFilterStatsOutifIndex, axsAccessFilterStatsOutifIndexType, axsAccessFilterStatsOutListIndex,axsAccessFilterStatsOutSequenceNumber } ::= { axsAccessFilterStatsOutTable 1 } AxsAccessFilterStatsOutEntry ::= SEQUENCE { axsAccessFilterStatsOutifIndex INTEGER, axsAccessFilterStatsOutifIndexType INTEGER, axsAccessFilterStatsOutListIndex Unsigned32, axsAccessFilterStatsOutSequenceNumber Unsigned32, axsAccessFilterStatsOutListName DisplayString, axsAccessFilterStatsOutMatchedPackets Counter64 } axsAccessFilterStatsOutifIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Index value in which entry of this table is identified." ::= { axsAccessFilterStatsOutEntry 1 } axsAccessFilterStatsOutifIndexType OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Indicates interface type. Physical port number : 1 Interface name : 2" ::= { axsAccessFilterStatsOutEntry 2 } axsAccessFilterStatsOutListIndex OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "Index value of access list that identifies entry of this table." ::= { axsAccessFilterStatsOutEntry 3 } axsAccessFilterStatsOutSequenceNumber OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "Sequence number of flow detection condition and operation information set to access list number or access list name. " ::= { axsAccessFilterStatsOutEntry 4 } axsAccessFilterStatsOutListName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Access list number or access list name corresponding to index of access list." ::= { axsAccessFilterStatsOutEntry 5 } axsAccessFilterStatsOutMatchedPackets OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Corresponding number of packets to flow detection condition of access list. " ::= { axsAccessFilterStatsOutEntry 6 } axsQosFlowStatsInTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsQosFlowStatsInEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table information on corresponding number of packets to QoS flow detection condition and operation information set in QoS flow list." ::= { axsQosFlowStats 1 } axsQosFlowStatsInEntry OBJECT-TYPE SYNTAX AxsQosFlowStatsInEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry concerning corresponding number of packets to QoS flow detection condition and operation information set in QoS Flower shop." INDEX { axsQosFlowStatsInifIndex, axsQosFlowStatsInifIndexType, axsQosFlowStatsInListIndex, axsQosFlowStatsInSequenceNumber } ::= { axsQosFlowStatsInTable 1 } AxsQosFlowStatsInEntry ::= SEQUENCE { axsQosFlowStatsInifIndex INTEGER, axsQosFlowStatsInifIndexType INTEGER, axsQosFlowStatsInListIndex Unsigned32, axsQosFlowStatsInSequenceNumber Unsigned32, axsQosFlowStatsInListName DisplayString, axsQosFlowStatsInMatchedPackets Counter64, axsQosFlowStatsInMatchedPacketsMinUnder Counter64, axsQosFlowStatsInMatchedPacketsMinOver Counter64, axsQosFlowStatsInMatchedPacketsMaxUnder Counter64, axsQosFlowStatsInMatchedPacketsMaxOver Counter64 } axsQosFlowStatsInifIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Index value in which entry of this table is identified." ::= { axsQosFlowStatsInEntry 1 } axsQosFlowStatsInifIndexType OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Indicates interface type. Physical port number : 1 Interface name : 2" ::= { axsQosFlowStatsInEntry 2 } axsQosFlowStatsInListIndex OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "Index value of QoS Flow list where entry of this table is identified." ::= { axsQosFlowStatsInEntry 3 } axsQosFlowStatsInSequenceNumber OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "Sequence number of flow detection condition and operation information set to QoS flow list name." ::= { axsQosFlowStatsInEntry 4 } axsQosFlowStatsInListName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "QoS flow list name corresponding to index of QoS flow list." ::= { axsQosFlowStatsInEntry 5 } axsQosFlowStatsInMatchedPackets OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Corresponding number of packets to flow detection condition of QoS flow list." ::= { axsQosFlowStatsInEntry 6 } axsQosFlowStatsInMatchedPacketsMinUnder OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Number of packets in which it agrees to flow detection condition of QoS flow list and the lowest band watch is observed." ::= { axsQosFlowStatsInEntry 7 } axsQosFlowStatsInMatchedPacketsMinOver OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Number of packets in which it agrees to flow detection condition of QoS flow list and it violates the lowest band watch." ::= { axsQosFlowStatsInEntry 8 } axsQosFlowStatsInMatchedPacketsMaxUnder OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Number of packets in which it agrees to flow detection condition of QoS flow list and the maximum band control is observed." ::= { axsQosFlowStatsInEntry 9 } axsQosFlowStatsInMatchedPacketsMaxOver OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Number of packets in which it agrees to flow detection condition of QoS flow list and it violates the maximum band control." ::= { axsQosFlowStatsInEntry 10 } -- axsL2ldMIB Group axsL2ldVersion OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The version of L2 loop detection." ::= { axsL2ldGlobalInfo 1 } axsL2ldLoopDetectionId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "L2 loop detection ID." ::= { axsL2ldGlobalInfo 2 } axsL2ldIntervalTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Sending interval of L2 loop detection frame." ::= { axsL2ldGlobalInfo 3 } axsL2ldOutputRate OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Sending rate of L2 loop detection frame." ::= { axsL2ldGlobalInfo 4 } axsL2ldThreshold OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Detection counts until port is put into state of inactive." ::= { axsL2ldGlobalInfo 5 } axsL2ldHoldTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Hold time of detection counts." ::= { axsL2ldGlobalInfo 6 } axsL2ldAutoRestoreTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Time until port put into state of inactive is put into state of active by automatic operation." ::= { axsL2ldGlobalInfo 7 } axsL2ldConfigurationVlanPortCounts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of VLAN ports set to send L2 loop detection frame." ::= { axsL2ldGlobalInfo 8 } axsL2ldCapacityVlanPortCounts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of VLAN ports that can be sent by L2 loop detection frame sending rate." ::= { axsL2ldGlobalInfo 9 } axsL2ldPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsL2ldPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing port information on L2 loop detection." ::= { axsL2ld 2 } axsL2ldPortEntry OBJECT-TYPE SYNTAX AxsL2ldPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of port information on L2 loop detection." INDEX { axsL2ldPortIndex,axsL2ldPortIfIndex } ::= { axsL2ldPortTable 1 } AxsL2ldPortEntry ::= SEQUENCE { axsL2ldPortIndex INTEGER, axsL2ldPortIfIndex INTEGER, axsL2ldPortStatus INTEGER, axsL2ldPortType INTEGER, axsL2ldPortDetectCount INTEGER, axsL2ldPortAutoRestoringTimer INTEGER, axsL2ldPortSourcePortIfindex INTEGER, axsL2ldPortDestinationPortIfindex INTEGER, axsL2ldPortSourceVlan INTEGER, axsL2ldPortHCInFrames Counter64, axsL2ldPortHCOutFrames Counter64, axsL2ldPortHCInDiscards Counter64, axsL2ldPortInactiveCount INTEGER, axsL2ldPortLastInactiveTime TimeStamp, axsL2ldPortLastInFramesTime TimeStamp } axsL2ldPortIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Index of L2 loop detection port." ::= { axsL2ldPortEntry 1 } axsL2ldPortIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ifIndex of L2 loop detection port." ::= { axsL2ldPortEntry 2 } axsL2ldPortStatus OBJECT-TYPE SYNTAX INTEGER { up (1), down (2), loopDown (3) } ACCESS read-only STATUS mandatory DESCRIPTION "State of L2 loop detection port." ::= { axsL2ldPortEntry 3 } axsL2ldPortType OBJECT-TYPE SYNTAX INTEGER { trap (1), sendInact (2), send (3), upLink (4), exception (5) } ACCESS read-only STATUS mandatory DESCRIPTION "Type of L2 loop detection port." ::= { axsL2ldPortEntry 4 } axsL2ldPortDetectCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of L2 loop detection. The number in which L2 loop detection frame is received in hold time." ::= { axsL2ldPortEntry 5 } axsL2ldPortAutoRestoringTimer OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Time until restoring it automatically. The value is 0 when port is active." ::= { axsL2ldPortEntry 6 } axsL2ldPortSourcePortIfindex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ifIndex of port transmitted when L2 loop detection frame was received at the end." ::= { axsL2ldPortEntry 7 } axsL2ldPortDestinationPortIfindex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ifIndex of port where L2 loop detection frame was received at the end." ::= { axsL2ldPortEntry 8 } axsL2ldPortSourceVlan OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "VLAN ID when transmitting when L2 loop detection frame was received at the end." ::= { axsL2ldPortEntry 9 } axsL2ldPortHCInFrames OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Number of receptions of L2 loop detection frames." ::= { axsL2ldPortEntry 10 } axsL2ldPortHCOutFrames OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmissions of L2 loop detection frames." ::= { axsL2ldPortEntry 11 } axsL2ldPortHCInDiscards OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "Number of receptions of L2 loop detection discard frames." ::= { axsL2ldPortEntry 12 } axsL2ldPortInactiveCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of put into state of inactive." ::= { axsL2ldPortEntry 13 } axsL2ldPortLastInactiveTime OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "Time put into state of inactive at the end." ::= { axsL2ldPortEntry 14 } axsL2ldPortLastInFramesTime OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "Time to have received L2 loop detection frame at the end." ::= { axsL2ldPortEntry 15 } -- AX VrfMIB Group axsVrfIpAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of addressing information relevant to this entity's IP addresses." ::= { axsVrfIp 1 } axsVrfIpAddrEntry OBJECT-TYPE SYNTAX AxsVrfIpAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The addressing information for one of this entity's IP addresses." INDEX { axsVrfIpAddrVrfIndex, axsVrfIpAdEntAddr } ::= { axsVrfIpAddrTable 1 } AxsVrfIpAddrEntry ::= SEQUENCE { axsVrfIpAddrVrfIndex INTEGER, axsVrfIpAdEntAddr IpAddress, axsVrfIpAdEntIfIndex INTEGER, axsVrfIpAdEntNetMask IpAddress, axsVrfIpAdEntBcastAddr INTEGER, axsVrfIpAdEntReasmMaxSize INTEGER, axsVrfIpAdEntDescr DisplayString } axsVrfIpAddrVrfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpAddrEntry 1 } axsVrfIpAdEntAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address to which this entry's addressing information pertains." ::= { axsVrfIpAddrEntry 2 } axsVrfIpAdEntIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable." ::= { axsVrfIpAddrEntry 3 } axsVrfIpAdEntNetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The subnet mask associated with the IP address of this entry." ::= { axsVrfIpAddrEntry 4 } axsVrfIpAdEntBcastAddr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry." ::= { axsVrfIpAddrEntry 5 } axsVrfIpAdEntReasmMaxSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The size of the largest IP dataaxram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface." ::= { axsVrfIpAddrEntry 6 } axsVrfIpAdEntDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpAddrEntry 7 } axsVrfIpNetToMediaTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpNetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The IP Address Translation table used for mapping from IP addresses to physical addresses." ::= { axsVrfIp 2 } axsVrfIpNetToMediaEntry OBJECT-TYPE SYNTAX AxsVrfIpNetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains one IpAddress to physical address equivalence." INDEX { axsVrfIpNetMediaVrfIndex, axsVrfIpNetToMediaIfIndex, axsVrfIpNetToMediaNetAddress } ::= { axsVrfIpNetToMediaTable 1 } AxsVrfIpNetToMediaEntry ::= SEQUENCE { axsVrfIpNetMediaVrfIndex INTEGER, axsVrfIpNetToMediaIfIndex INTEGER, axsVrfIpNetToMediaPhysAddress PhysAddress, axsVrfIpNetToMediaNetAddress IpAddress, axsVrfIpNetToMediaType INTEGER, axsVrfIpNetToMediaDescr DisplayString } axsVrfIpNetMediaVrfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpNetToMediaEntry 1 } axsVrfIpNetToMediaIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The interface on which this entry's equivalence is effective. This index is same value of ifIndex." ::= { axsVrfIpNetToMediaEntry 2 } axsVrfIpNetToMediaPhysAddress OBJECT-TYPE SYNTAX PhysAddress ACCESS read-only STATUS mandatory DESCRIPTION "The media-dependent `physical' address." ::= { axsVrfIpNetToMediaEntry 3 } axsVrfIpNetToMediaNetAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IpAddress corresponding to the media- dependent `physical' address." ::= { axsVrfIpNetToMediaEntry 4 } axsVrfIpNetToMediaType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following ex. Inverse ARP invalid(2), -- an invalidated mapping dynamic(3), static(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of mapping." ::= { axsVrfIpNetToMediaEntry 5 } axsVrfIpNetToMediaDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpNetToMediaEntry 6 } axsVrfIpFwNoTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpFwNoEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's number of IP Routing table about VRF." ::= { axsVrfIpForward 1 } axsVrfIpFwNoEntry OBJECT-TYPE SYNTAX AxsVrfIpFwNoEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's IP Routing table about VRF." INDEX { axsVrfIpFwNoVRFIndex } ::= { axsVrfIpFwNoTable 1 } AxsVrfIpFwNoEntry ::= SEQUENCE { axsVrfIpFwNoVRFIndex INTEGER, axsVrfIpFwNo INTEGER, axsVrfIpFwNoDescr DisplayString } axsVrfIpFwNoVRFIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpFwNoEntry 1 } axsVrfIpFwNo OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of entry that is IP Routing table." ::= { axsVrfIpFwNoEntry 2 } axsVrfIpFwNoDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpFwNoEntry 3 } axsVrfIpFwTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpFwEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's IP Routing table." ::= { axsVrfIpForward 2 } axsVrfIpFwEntry OBJECT-TYPE SYNTAX AxsVrfIpFwEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A particular route to a particular destination, under a particular policy." INDEX { axsVrfIpFwVRFIndex, axsVrfIpFwDest, axsVrfIpFwProto, axsVrfIpFwPolicy, axsVrfIpFwNextHop } ::= { axsVrfIpFwTable 1 } AxsVrfIpFwEntry ::= SEQUENCE { axsVrfIpFwVRFIndex INTEGER, axsVrfIpFwDest IpAddress, axsVrfIpFwMask IpAddress, axsVrfIpFwPolicy INTEGER, axsVrfIpFwNextHop IpAddress, axsVrfIpFwIfIndex INTEGER, axsVrfIpFwType INTEGER, axsVrfIpFwProto INTEGER, axsVrfIpFwAge INTEGER, axsVrfIpFwInfo OBJECT IDENTIFIER, axsVrfIpFwNextHopAS INTEGER, axsVrfIpFwMetric1 INTEGER, axsVrfIpFwMetric2 INTEGER, axsVrfIpFwMetric3 INTEGER, axsVrfIpFwMetric4 INTEGER, axsVrfIpFwMetric5 INTEGER, axsVrfIpFwDescr DisplayString } axsVrfIpFwVRFIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpFwEntry 1 } axsVrfIpFwDest OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The destination IP address of this route." ::= { axsVrfIpFwEntry 2 } axsVrfIpFwMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipForwardDest field." ::= { axsVrfIpFwEntry 3 } axsVrfIpFwPolicy OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The general set of conditions that would cause the selection of one multipath route (set of next hops for a given destination) is referred to as 'policy'." ::= { axsVrfIpFwEntry 4 } axsVrfIpFwNextHop OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "On remote routes, the address of the next system en route." ::= { axsVrfIpFwEntry 5 } axsVrfIpFwIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The ifIndex value which identifies the local interface through which the next hop of this route should be reached." ::= { axsVrfIpFwEntry 6 } axsVrfIpFwType OBJECT-TYPE SYNTAX INTEGER{ other(1), -- not specified by this MIB invalid(2), -- logically deleted local(3), -- local interface remote(4) -- remote destination } ACCESS read-only STATUS mandatory DESCRIPTION "The type of route." ::= { axsVrfIpFwEntry 7 } axsVrfIpFwProto OBJECT-TYPE SYNTAX INTEGER { other(1), -- not specified local(2), -- local interface netmgmt(3), -- static route rip(8), -- Berkeley RIP or RIP-II ospf(13), -- Open Shortest Path First bgp(14) -- Border Gateway Protocol } ACCESS read-only STATUS mandatory DESCRIPTION "The routing mechanism via which this route was learned." ::= { axsVrfIpFwEntry 8 } axsVrfIpFwAge OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds since this route was last updated or otherwise determined to be correct." ::= { axsVrfIpFwEntry 9 } axsVrfIpFwInfo OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipForwardProto value. Its value be set to the OBJECT IDENTIFIER { 0 0 }." ::= { axsVrfIpFwEntry 10 } axsVrfIpFwNextHopAS OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Autonomous System Number of the Next Hop." ::= { axsVrfIpFwEntry 11 } axsVrfIpFwMetric1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The primary routing metric for this route." ::= { axsVrfIpFwEntry 12 } axsVrfIpFwMetric2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route." ::= { axsVrfIpFwEntry 13 } axsVrfIpFwMetric3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. Its value is set to -1." ::= { axsVrfIpFwEntry 14 } axsVrfIpFwMetric4 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. Its value is set to -1." ::= { axsVrfIpFwEntry 15 } axsVrfIpFwMetric5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. Its value is set to -1." ::= { axsVrfIpFwEntry 16 } axsVrfIpFwDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpFwEntry 17 } axsVrfIpv6AddrTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpv6AddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of addressing information relevant to this node's interface IPv6 addresses per VRF." ::= { axsVrfIpv6 1 } axsVrfIpv6AddrEntry OBJECT-TYPE SYNTAX AxsVrfIpv6AddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The addressing information for one of this entity's IPv6 addresses per VRF." INDEX { axsVrfIpv6AddrVrfIndex, axsVrfIpv6AddrIfIndex, axsVrfIpv6AddrAddress } ::= { axsVrfIpv6AddrTable 1 } AxsVrfIpv6AddrEntry ::= SEQUENCE { axsVrfIpv6AddrVrfIndex INTEGER, axsVrfIpv6AddrIfIndex INTEGER, axsVrfIpv6AddrAddress Ipv6Address, axsVrfIpv6AddrPfxLength INTEGER, axsVrfIpv6AddrType INTEGER, axsVrfIpv6AddrAnycastFlag TruthValue, axsVrfIpv6AddrStatus INTEGER, axsVrfIpv6AddrDescr DisplayString } axsVrfIpv6AddrVrfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpv6AddrEntry 1 } axsVrfIpv6AddrIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable." ::= { axsVrfIpv6AddrEntry 2 } axsVrfIpv6AddrAddress OBJECT-TYPE SYNTAX Ipv6Address ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 address to which this entry's addressing information pertains." ::= { axsVrfIpv6AddrEntry 3 } axsVrfIpv6AddrPfxLength OBJECT-TYPE SYNTAX INTEGER(0..128) ACCESS read-only STATUS mandatory DESCRIPTION "The length of the prefix (in bits) associated with the IPv6 address of this entry." ::= { axsVrfIpv6AddrEntry 4 } axsVrfIpv6AddrType OBJECT-TYPE SYNTAX INTEGER { -- address has been formed -- using stateless stateless(1), -- autoconfiguration -- address has been acquired -- by stateful means -- (e.g. DHCPv6, manual stateful(2), -- configuration) -- type can not be determined unknown(3) -- for some reason. } ACCESS read-only STATUS mandatory DESCRIPTION "The type of address. Note that 'stateless(1)' refers to an address that was statelessly autoconfigured; 'stateful(2)' refers to a address which was acquired by via a stateful protocol (e.g. DHCPv6, manual configuration)." ::= { axsVrfIpv6AddrEntry 5 } axsVrfIpv6AddrAnycastFlag OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise." ::= { axsVrfIpv6AddrEntry 6 } axsVrfIpv6AddrStatus OBJECT-TYPE SYNTAX INTEGER { preferred(1), deprecated(2), invalid(3), inaccessible(4), unknown(5) -- status can not be determined -- for some reason. } ACCESS read-only STATUS mandatory DESCRIPTION "Address status. The preferred(1) state indicates that this is a valid address that can appear as the destination or source address of a packet. The deprecated(2) state indicates that this is a valid but deprecated address that should no longer be used as a source address in new communications, but packets addressed to such an address are processed as expected. The invalid(3) state indicates that this is not valid address which should not appear as the destination or source address of a packet. The inaccessible(4) state indicates that the address is not accessible because the interface to which this address is assigned is not operational." ::= { axsVrfIpv6AddrEntry 7 } axsVrfIpv6AddrDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpv6AddrEntry 8 } axsVrfIpv6AddrPrefixTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpv6AddrPrefixEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The list of IPv6 address prefixes of IPv6 interfaces." ::= { axsVrfIpv6 2 } axsVrfIpv6AddrPrefixEntry OBJECT-TYPE SYNTAX AxsVrfIpv6AddrPrefixEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An interface entry containing objects of a particular IPv6 address prefix." INDEX { axsVrfIpv6AddrPrefixVrfIndex, axsVrfIpv6AddrPrefixIfIndex, axsVrfIpv6AddrPrefix, axsVrfIpv6AddrPrefixLength } ::= { axsVrfIpv6AddrPrefixTable 1 } AxsVrfIpv6AddrPrefixEntry ::= SEQUENCE { axsVrfIpv6AddrPrefixVrfIndex INTEGER, axsVrfIpv6AddrPrefixIfIndex INTEGER, axsVrfIpv6AddrPrefix Ipv6AddressPrefix, axsVrfIpv6AddrPrefixLength INTEGER (0..128), axsVrfIpv6AddrPrefixOnLinkFlag TruthValue, axsVrfIpv6AddrPrefixAutonomousFlag TruthValue, axsVrfIpv6AddrPrefixAdvPreferredLifetime Unsigned32, axsVrfIpv6AddrPrefixAdvValidLifetime Unsigned32 } axsVrfIpv6AddrPrefixVrfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpv6AddrPrefixEntry 1 } axsVrfIpv6AddrPrefixIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable." ::= { axsVrfIpv6AddrPrefixEntry 2 } axsVrfIpv6AddrPrefix OBJECT-TYPE SYNTAX Ipv6AddressPrefix ACCESS not-accessible STATUS mandatory DESCRIPTION "The prefix associated with the this interface." ::= { axsVrfIpv6AddrPrefixEntry 3 } axsVrfIpv6AddrPrefixLength OBJECT-TYPE SYNTAX INTEGER (0..128) ACCESS not-accessible STATUS mandatory DESCRIPTION "The length of the prefix (in bits)." ::= { axsVrfIpv6AddrPrefixEntry 4 } axsVrfIpv6AddrPrefixOnLinkFlag OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "This object has the value 'true(1)', if this prefix can be used for on-link determination and the value 'false(2)' otherwise." ::= { axsVrfIpv6AddrPrefixEntry 5 } axsVrfIpv6AddrPrefixAutonomousFlag OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Autonomous address configuration flag. When true(1), indicates that this prefix can be used for autonomous address configuration (i.e. can be used to form a local interface address). If false(2), it is not used to autoconfigure a local interface address." ::= { axsVrfIpv6AddrPrefixEntry 6 } axsVrfIpv6AddrPrefixAdvPreferredLifetime OBJECT-TYPE SYNTAX Unsigned32 ACCESS read-only STATUS mandatory DESCRIPTION "It is the length of time in seconds that this prefix will remain preferred, i.e. time until deprecation. A value of 4,294,967,295 represents infinity. The address generated from a deprecated prefix should no longer be used as a source address in new communications, but packets received on such an interface are processed as expected." ::= { axsVrfIpv6AddrPrefixEntry 7 } axsVrfIpv6AddrPrefixAdvValidLifetime OBJECT-TYPE SYNTAX Unsigned32 ACCESS read-only STATUS mandatory DESCRIPTION "It is the length of time in seconds that this prefix will remain valid, i.e. time until invalidation. A value of 4,294,967,295 represents infinity. The address generated from an invalidated prefix should not appear as the destination or source address of a packet." ::= { axsVrfIpv6AddrPrefixEntry 8 } axsVrfIpv6NetToMediaTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpv6NetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The IPv6 Address Translation table used for mapping from IPv6 addresses to physical addresses per VRF. The IPv6 address translation table contain the Ipv6Address to `physical' address equivalencies. Some interfaces do not use translation tables for determining address equivalencies; if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries." ::= { axsVrfIpv6 3 } axsVrfIpv6NetToMediaEntry OBJECT-TYPE SYNTAX AxsVrfIpv6NetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains one IPv6 address to `physical' address equivalence per VRF." INDEX { axsVrfIpv6NetToMediaVrfIndex, axsVrfIpv6NetToMediaIfIndex, axsVrfIpv6NetToMediaNetAddress } ::= { axsVrfIpv6NetToMediaTable 1 } AxsVrfIpv6NetToMediaEntry ::= SEQUENCE { axsVrfIpv6NetToMediaVrfIndex INTEGER, axsVrfIpv6NetToMediaIfIndex INTEGER, axsVrfIpv6NetToMediaNetAddress Ipv6Address, axsVrfIpv6NetToMediaPhysAddress PhysAddress, axsVrfIpv6NetToMediaType INTEGER, axsVrfIpv6IfNetToMediaState INTEGER, axsVrfIpv6IfNetToMediaLastUpdated TimeStamp, axsVrfIpv6NetToMediaValid TruthValue, axsVrfIpv6NetToMediaDescr DisplayString } axsVrfIpv6NetToMediaVrfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpv6NetToMediaEntry 1 } axsVrfIpv6NetToMediaIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable." ::= { axsVrfIpv6NetToMediaEntry 2 } axsVrfIpv6NetToMediaNetAddress OBJECT-TYPE SYNTAX Ipv6Address ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 Address corresponding to the media-dependent `physical' address." ::= { axsVrfIpv6NetToMediaEntry 3 } axsVrfIpv6NetToMediaPhysAddress OBJECT-TYPE SYNTAX PhysAddress ACCESS read-only STATUS mandatory DESCRIPTION "The media-dependent `physical' address." ::= { axsVrfIpv6NetToMediaEntry 4 } axsVrfIpv6NetToMediaType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following dynamic(2), -- dynamically resolved static(3), -- statically configured local(4) -- local interface } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that the mapping has been statically configured. The local(4) indicates that the mapping is provided for an entity's own interface address." ::= { axsVrfIpv6NetToMediaEntry 5 } axsVrfIpv6IfNetToMediaState OBJECT-TYPE SYNTAX INTEGER { reachable(1), -- confirmed reachability stale(2), -- unconfirmed reachability delay(3), -- waiting for reachability -- confirmation before entering -- the probe state probe(4), -- actively probing invalid(5), -- an invalidated mapping unknown(6) -- state can not be determined -- for some reason. } ACCESS read-only STATUS mandatory DESCRIPTION "The Neighbor Unreachability Detection [8] state for the interface when the address mapping in this entry is used." ::= { axsVrfIpv6NetToMediaEntry 6 } axsVrfIpv6IfNetToMediaLastUpdated OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { axsVrfIpv6NetToMediaEntry 7 } axsVrfIpv6NetToMediaValid OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Setting this object to the value 'false(2)' has the effect of invalidating the corresponding entry in the ipv6NetToMediaTable. That is, it effectively disassociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipv6NetToMediaValid object." ::= { axsVrfIpv6NetToMediaEntry 8 } axsVrfIpv6NetToMediaDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpv6NetToMediaEntry 9 } axsVrfIpv6FwNoTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpv6FwNoEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's number of IPv6 Routing table about VRF." ::= { axsVrfIpv6Forward 1 } axsVrfIpv6FwNoEntry OBJECT-TYPE SYNTAX AxsVrfIpv6FwNoEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's IPv6 Routing table about VRF." INDEX { axsVrfIpv6FwNoVRFIndex } ::= { axsVrfIpv6FwNoTable 1 } AxsVrfIpv6FwNoEntry ::= SEQUENCE { axsVrfIpv6FwNoVRFIndex INTEGER, axsVrfIpv6FwNo INTEGER, axsVrfIpv6FwNoDescr DisplayString } axsVrfIpv6FwNoVRFIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpv6FwNoEntry 1 } axsVrfIpv6FwNo OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of entry that is IPv6 Routing table." ::= { axsVrfIpv6FwNoEntry 2 } axsVrfIpv6FwNoDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpv6FwNoEntry 3 } axsVrfIpv6FwTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsVrfIpv6FwEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's IPv6 Routing table." ::= { axsVrfIpv6Forward 2 } axsVrfIpv6FwEntry OBJECT-TYPE SYNTAX AxsVrfIpv6FwEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A particular route to a particular destination, under a particular policy." INDEX { axsVrfIpv6FwVrfIndex, axsVrfIpv6FwDest, axsVrfIpv6FwProto, axsVrfIpv6FwPolicy, axsVrfIpv6FwNextHop } ::= { axsVrfIpv6FwTable 1 } AxsVrfIpv6FwEntry ::= SEQUENCE { axsVrfIpv6FwVrfIndex INTEGER, axsVrfIpv6FwDest Ipv6Address, axsVrfIpv6FwPfxLength INTEGER, axsVrfIpv6FwPolicy INTEGER, axsVrfIpv6FwNextHop Ipv6Address, axsVrfIpv6FwIfIndex INTEGER, axsVrfIpv6FwType INTEGER, axsVrfIpv6FwProto INTEGER, axsVrfIpv6FwAge INTEGER, axsVrfIpv6FwInfo OBJECT IDENTIFIER, axsVrfIpv6FwNextHopAS INTEGER, axsVrfIpv6FwMetric1 INTEGER, axsVrfIpv6FwMetric2 INTEGER, axsVrfIpv6FwMetric3 INTEGER, axsVrfIpv6FwMetric4 INTEGER, axsVrfIpv6FwMetric5 INTEGER, axsVrfIpv6FwDescr DisplayString } axsVrfIpv6FwVrfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which identifies VRF number." ::= { axsVrfIpv6FwEntry 1 } axsVrfIpv6FwDest OBJECT-TYPE SYNTAX Ipv6Address ACCESS read-only STATUS mandatory DESCRIPTION "The destination IPv6 address of this route." ::= { axsVrfIpv6FwEntry 2 } axsVrfIpv6FwPfxLength OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The length of the prefix (in bits) associated with the IPv6 address of this entry." ::= { axsVrfIpv6FwEntry 3 } axsVrfIpv6FwPolicy OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The general set of conditions that would cause the selection of one multipath route (set of next hops for a given destination) is referred to as 'policy'." ::= { axsVrfIpv6FwEntry 4 } axsVrfIpv6FwNextHop OBJECT-TYPE SYNTAX Ipv6Address ACCESS read-only STATUS mandatory DESCRIPTION "On remote routes, the address of the next system en route." ::= { axsVrfIpv6FwEntry 5 } axsVrfIpv6FwIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The ifIndex value which identifies the local interface through which the next hop of this route should be reached." ::= { axsVrfIpv6FwEntry 6 } axsVrfIpv6FwType OBJECT-TYPE SYNTAX INTEGER{ other(1), -- not specified by this MIB invalid(2), -- logically deleted local(3), -- local interface remote(4) -- remote destination } ACCESS read-only STATUS mandatory DESCRIPTION "The type of route." ::= { axsVrfIpv6FwEntry 7 } axsVrfIpv6FwProto OBJECT-TYPE SYNTAX INTEGER { other(1), -- not specified local(2), -- local interface netmgmt(3), -- static route rip(8), -- Berkeley RIP or RIP-II ospf(13), -- Open Shortest Path First bgp(14) -- Border Gateway Protocol } ACCESS read-only STATUS mandatory DESCRIPTION "The routing mechanism via which this route was learned." ::= { axsVrfIpv6FwEntry 8 } axsVrfIpv6FwAge OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds since this route was last updated or otherwise determined to be correct." ::= { axsVrfIpv6FwEntry 9 } axsVrfIpv6FwInfo OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's axsVrfIpv6FwProto value. Its value be set to the OBJECT IDENTIFIER { 0 0 }." ::= { axsVrfIpv6FwEntry 10 } axsVrfIpv6FwNextHopAS OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Autonomous System Number of the Next Hop." ::= { axsVrfIpv6FwEntry 11 } axsVrfIpv6FwMetric1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The primary routing metric for this route." ::= { axsVrfIpv6FwEntry 12 } axsVrfIpv6FwMetric2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route." ::= { axsVrfIpv6FwEntry 13 } axsVrfIpv6FwMetric3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. Its value is set to -1." ::= { axsVrfIpv6FwEntry 14 } axsVrfIpv6FwMetric4 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. Its value is set to -1." ::= { axsVrfIpv6FwEntry 15 } axsVrfIpv6FwMetric5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An alternate routing metric for this route. Its value is set to -1." ::= { axsVrfIpv6FwEntry 16 } axsVrfIpv6FwDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Description of VRF. The VRF identification which user setting." ::= { axsVrfIpv6FwEntry 17 } -- OSPF General Variables axsOspfGeneralTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfGeneralEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of OSPF information." ::= { axsOspf 1 } axsOspfGeneralEntry OBJECT-TYPE SYNTAX AxsOspfGeneralEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of OSPF information." INDEX { axsOspfGeneralDomainNumber } ::= { axsOspfGeneralTable 1 } AxsOspfGeneralEntry ::= SEQUENCE { axsOspfGeneralDomainNumber INTEGER, axsOspfRouterId IpAddress, axsOspfAdminStat INTEGER, axsOspfVersionNumber INTEGER, axsOspfAreaBdrRtrStatus INTEGER, axsOspfASBdrRtrStatus INTEGER, axsOspfExternLsaCount Gauge, axsOspfExternLsaCksumSum INTEGER, axsOspfTOSSupport INTEGER, axsOspfOriginateNewLsas Counter, axsOspfRxNewLsas Counter, axsOspfExtLsdbLimit INTEGER, axsOspfMulticastExtensions INTEGER } axsOspfGeneralDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Domain number in the Autonomous System." ::= { axsOspfGeneralEntry 1 } axsOspfRouterId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "A integer uniquely identifying the router in the Autonomous System." ::= { axsOspfGeneralEntry 2 } axsOspfAdminStat OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The administrative status of OSPF in the router. " ::= { axsOspfGeneralEntry 3 } axsOspfVersionNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The current version number of the OSPF protocol is 2." ::= { axsOspfGeneralEntry 4 } axsOspfAreaBdrRtrStatus OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } ACCESS read-only STATUS mandatory DESCRIPTION "A flag to note whether this router is an area border router." ::= { axsOspfGeneralEntry 5 } axsOspfASBdrRtrStatus OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } ACCESS read-only STATUS mandatory DESCRIPTION "A flag to note whether this router is configured as an Autonomous System border router." ::= { axsOspfGeneralEntry 6 } axsOspfExternLsaCount OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The number of external (LS type 5) link-state advertisements in the link-state database." ::= { axsOspfGeneralEntry 7 } axsOspfExternLsaCksumSum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The 32-bit unsigned sum of the LS checksums of the external link-state advertisements contained in the link-state database." ::= { axsOspfGeneralEntry 8 } axsOspfTOSSupport OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The router's support for type-of-service routing. This value of false(2). " ::= { axsOspfGeneralEntry 9 } axsOspfOriginateNewLsas OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of new link-state advertisements that have been originated. " ::= { axsOspfGeneralEntry 10 } axsOspfRxNewLsas OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of link-state advertisements received determined to be new instantiations." ::= { axsOspfGeneralEntry 11 } axsOspfExtLsdbLimit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of non-default AS-external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. This value is -1" ::= { axsOspfGeneralEntry 12 } axsOspfMulticastExtensions OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A Bit Mask indicating whether the router is forwarding IP multicast (Class D) datagrams based on the algorithms defined in the Multicast Extensions to OSPF." ::= { axsOspfGeneralEntry 13 } axsOspfAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfAreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The router's support for demand routing." ::= { axsOspf 2 } axsOspfAreaEntry OBJECT-TYPE SYNTAX AxsOspfAreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry contain ospf area information." INDEX { axsOspfAreaDomainNumber, axsOspfAreaId } ::= { axsOspfAreaTable 1 } AxsOspfAreaEntry ::= SEQUENCE { axsOspfAreaDomainNumber INTEGER, axsOspfAreaId IpAddress, axsOspfAuthType INTEGER, axsOspfImportAsExtern INTEGER, axsOspfSpfRuns Counter, axsOspfAreaBdrRtrCount Gauge, axsOspfAsBdrRtrCount Gauge, axsOspfAreaLsaCount Gauge, axsOspfAreaLsaCksumSum INTEGER, axsOspfAreaSummary INTEGER, axsOspfAreaStatus INTEGER } axsOspfAreaDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "An uniquely identifying number of domain." ::= { axsOspfAreaEntry 1 } axsOspfAreaId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "A 32-bit integer uniquely identifying an area." ::= { axsOspfAreaEntry 2 } axsOspfAuthType OBJECT-TYPE SYNTAX INTEGER -- none(0), -- simplePassword (1), -- md5(2) ACCESS read-only STATUS mandatory DESCRIPTION "The authentication type specified for an area." ::= { axsOspfAreaEntry 3 } axsOspfImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal (1), importNoExternal (2), importNssa (3) } ACCESS read-only STATUS mandatory DESCRIPTION "The area's support for importing AS external link- state advertisements." ::= { axsOspfAreaEntry 4 } axsOspfSpfRuns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link-state database." ::= { axsOspfAreaEntry 5 } axsOspfAreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The total number of area border routers reachable within this area." ::= { axsOspfAreaEntry 6 } axsOspfAsBdrRtrCount OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The total number of AS area border routers reachable within this area." ::= { axsOspfAreaEntry 7 } axsOspfAreaLsaCount OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The total number of LSA(link-state advertisements) in this area. Excluding AS External LSA's" ::= { axsOspfAreaEntry 8 } axsOspfAreaLsaCksumSum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The sum of LSA's LS checksums contained in this area's link-state database." ::= { axsOspfAreaEntry 9 } axsOspfAreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary (1), sendAreaSummary (2) } ACCESS read-only STATUS mandatory DESCRIPTION "The variable axsOspfAreaSummary controls the import of summary LSAs into stub areas." ::= { axsOspfAreaEntry 10 } axsOspfAreaStatus OBJECT-TYPE SYNTAX INTEGER { active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. Value is only valid(1)." ::= { axsOspfAreaEntry 11 } axsOspfStubAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfStubAreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The set of metrics that will be advertised by a default Area Border Router into a stub area." ::= { axsOspf 3 } axsOspfStubAreaEntry OBJECT-TYPE SYNTAX AxsOspfStubAreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The metric for a given Type of Service that will be advertised by a default Area Border Router into a stub area." INDEX { axsOspfStubDomainNumber, axsOspfStubAreaId, axsOspfStubTOS } ::= { axsOspfStubAreaTable 1 } AxsOspfStubAreaEntry ::= SEQUENCE { axsOspfStubDomainNumber INTEGER, axsOspfStubAreaId IpAddress, axsOspfStubTOS INTEGER, axsOspfStubMetric INTEGER, axsOspfStubStatus INTEGER, axsOspfStubMetricType INTEGER } axsOspfStubDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The domain identifier for the Stub Area." ::= { axsOspfStubAreaEntry 1 } axsOspfStubAreaId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The identifier for the Stub Area." ::= { axsOspfStubAreaEntry 2 } axsOspfStubTOS OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Type of Service associated with the metric. Value is only 0." ::= { axsOspfStubAreaEntry 3 } axsOspfStubMetric OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The metric value applied at the indicated type of service." ::= { axsOspfStubAreaEntry 4 } axsOspfStubStatus OBJECT-TYPE SYNTAX INTEGER { active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. This value is only valid(1)." ::= { axsOspfStubAreaEntry 5 } axsOspfStubMetricType OBJECT-TYPE SYNTAX INTEGER { ospfMetric(1), comparableCost(2), nonComparable(3) } ACCESS read-only STATUS mandatory DESCRIPTION "his variable displays the type of metric advertised as a default route." ::= { axsOspfStubAreaEntry 6 } axsOspfLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The OSPF Process's Link State Database." ::= { axsOspf 4 } axsOspfLsdbEntry OBJECT-TYPE SYNTAX AxsOspfLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single Link State Advertisement." INDEX { axsOspfLsdbDomainNumber, axsOspfLsdbAreaId, axsOspfLsdbType, axsOspfLsdbLsid, axsOspfLsdbRouterId } ::= { axsOspfLsdbTable 1 } AxsOspfLsdbEntry ::= SEQUENCE { axsOspfLsdbDomainNumber INTEGER, axsOspfLsdbAreaId IpAddress, axsOspfLsdbType INTEGER, axsOspfLsdbLsid IpAddress, axsOspfLsdbRouterId IpAddress, axsOspfLsdbSequence INTEGER, axsOspfLsdbAge INTEGER, axsOspfLsdbChecksum INTEGER, axsOspfLsdbAdvertisement OCTET STRING } axsOspfLsdbDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The identifier of the domain from which the LSA was received." ::= { axsOspfLsdbEntry 1 } axsOspfLsdbAreaId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The 32 bit identifier of the Area from which the LSA was received." ::= { axsOspfLsdbEntry 2 } axsOspfLsdbType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), -- but see axsOspfExtLsdbTable multicastLink (6), nssaExternalLink (7) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the link state advertisement." ::= { axsOspfLsdbEntry 3 } axsOspfLsdbLsid OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Link State ID . It identifies the piece of the routing domain that is being described by the advertisement." ::= { axsOspfLsdbEntry 4 } axsOspfLsdbRouterId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The number that uniquely identifies the originating router in the Autonomous System." ::= { axsOspfLsdbEntry 5 } axsOspfLsdbSequence OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The sequence number field is a signed 32-bit integer." ::= { axsOspfLsdbEntry 6 } axsOspfLsdbAge OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This the age of the link state adver- tisement in seconds." ::= { axsOspfLsdbEntry 7 } axsOspfLsdbChecksum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field." ::= { axsOspfLsdbEntry 8 } axsOspfLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The entire Link State Advertisement, including its header." ::= { axsOspfLsdbEntry 9 } axsOspfAreaRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfAreaRangeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A range of IP addresses specified by an IP address/IP network mask pair." ::= { axsOspf 5 } axsOspfAreaRangeEntry OBJECT-TYPE SYNTAX AxsOspfAreaRangeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A range of IP addresses specified by an IP address/IP network mask pair." INDEX { axsOspfAreaRangeDomainNumber, axsOspfAreaRangeAreaId, axsOspfAreaRangeNet } ::= { axsOspfAreaRangeTable 1 } AxsOspfAreaRangeEntry ::= SEQUENCE { axsOspfAreaRangeDomainNumber INTEGER, axsOspfAreaRangeAreaId IpAddress, axsOspfAreaRangeNet IpAddress, axsOspfAreaRangeMask IpAddress, axsOspfAreaRangeStatus INTEGER, axsOspfAreaRangeEffect INTEGER } axsOspfAreaRangeDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Domain number of the Area." ::= { axsOspfAreaRangeEntry 1 } axsOspfAreaRangeAreaId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Area the Address Range is to be found within." ::= { axsOspfAreaRangeEntry 2 } axsOspfAreaRangeNet OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP Address of the Net or Subnet indicated by the range." ::= { axsOspfAreaRangeEntry 3 } axsOspfAreaRangeMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Subnet Mask that pertains to the Net or Subnet." ::= { axsOspfAreaRangeEntry 4 } axsOspfAreaRangeStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. This value is only valid(1)." ::= { axsOspfAreaRangeEntry 5 } axsOspfAreaRangeEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching (1), doNotAdvertiseMatching (2) } ACCESS read-only STATUS mandatory DESCRIPTION "Subnets subsumed by ranges either trigger the advertisement of the indicated summary (adver- tiseMatching), or result in the subnet's not being advertised at all outside the area." ::= { axsOspfAreaRangeEntry 6 } axsOspfIfTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The OSPF Interface Table describes the interfaces from the viewpoint of OSPF." ::= { axsOspf 7 } axsOspfIfEntry OBJECT-TYPE SYNTAX AxsOspfIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The OSPF Interface Entry describes one interface from the viewpoint of OSPF." INDEX { axsOspfIfDomainNumber, axsOspfIfIpAddress, axsOspfAddressLessIf } ::= { axsOspfIfTable 1 } AxsOspfIfEntry ::= SEQUENCE { axsOspfIfDomainNumber INTEGER, axsOspfIfIpAddress IpAddress, axsOspfAddressLessIf INTEGER, axsOspfIfAreaId IpAddress, axsOspfIfType INTEGER, axsOspfIfAdminStat INTEGER, axsOspfIfRtrPriority INTEGER, axsOspfIfTransitDelay INTEGER, axsOspfIfRetransInterval INTEGER, axsOspfIfHelloInterval INTEGER, axsOspfIfRtrDeadInterval INTEGER, axsOspfIfPollInterval INTEGER, axsOspfIfState INTEGER, axsOspfIfDesignatedRouter IpAddress, axsOspfIfEvents Counter, axsOspfIfAuthKey OCTET STRING, axsOspfIfStatus INTEGER, axsOspfIfMulticastForwarding INTEGER, axsOspfIfBackupDesignatedRouter IpAddress } axsOspfIfDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The domain number of this OSPF interface." ::= { axsOspfIfEntry 1 } axsOspfIfIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of this OSPF interface." ::= { axsOspfIfEntry 2 } axsOspfAddressLessIf OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address." ::= { axsOspfIfEntry 3 } axsOspfIfAreaId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "A integer uniquely identifying the area to which the interface connects." ::= { axsOspfIfEntry 4 } axsOspfIfType OBJECT-TYPE SYNTAX INTEGER { broadcast (1), nbma (2), pointToPoint (3), pointToMultipoint (5) } ACCESS read-only STATUS mandatory DESCRIPTION "The OSPF interface type." ::= { axsOspfIfEntry 5 } axsOspfIfAdminStat OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The OSPF interface's administrative status." ::= { axsOspfIfEntry 6 } axsOspfIfRtrPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The priority of this interface." ::= { axsOspfIfEntry 7 } axsOspfIfTransitDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." ::= { axsOspfIfEntry 8 } axsOspfIfRetransInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface." ::= { axsOspfIfEntry 9 } axsOspfIfHelloInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the interface." ::= { axsOspfIfEntry 10 } axsOspfIfRtrDeadInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down." ::= { axsOspfIfEntry 11 } axsOspfIfPollInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor." ::= { axsOspfIfEntry 12 } axsOspfIfState OBJECT-TYPE SYNTAX INTEGER { down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) } ACCESS read-only STATUS mandatory DESCRIPTION "The OSPF Interface State." ::= { axsOspfIfEntry 13 } axsOspfIfDesignatedRouter OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP Address of the Designated Router." ::= { axsOspfIfEntry 14 } axsOspfIfEvents OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this OSPF interface has changed its state, or an error has occurred." ::= { axsOspfIfEntry 16 } axsOspfIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The Authentication Key." ::= { axsOspfIfEntry 17 } axsOspfIfStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. this value is only valid(1)." ::= { axsOspfIfEntry 18 } axsOspfIfMulticastForwarding OBJECT-TYPE SYNTAX INTEGER { blocked (1), -- no multicast forwarding multicast (2), -- using multicast address unicast (3) -- to each OSPF neighbor } ACCESS read-only STATUS mandatory DESCRIPTION "The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts." ::= { axsOspfIfEntry 19 } axsOspfIfBackupDesignatedRouter OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP Address of the Backup Designated Router." ::= { axsOspfIfEntry 15 } axsOspfIfMetricTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfIfMetricEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The TOS metrics for a non-virtual interface identified by the interface index." ::= { axsOspf 8 } axsOspfIfMetricEntry OBJECT-TYPE SYNTAX AxsOspfIfMetricEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A particular TOS metric for a non-virtual interface identified by the interface index." INDEX { axsOspfIfMetricDomainNumber, axsOspfIfMetricIpAddress, axsOspfIfMetricAddressLessIf, axsOspfIfMetricTOS } ::= { axsOspfIfMetricTable 1 } AxsOspfIfMetricEntry ::= SEQUENCE { axsOspfIfMetricDomainNumber INTEGER, axsOspfIfMetricIpAddress IpAddress, axsOspfIfMetricAddressLessIf INTEGER, axsOspfIfMetricTOS INTEGER, axsOspfIfMetricValue INTEGER, axsOspfIfMetricStatus INTEGER } axsOspfIfMetricDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The domain number of this OSPF interface." ::= { axsOspfIfMetricEntry 1 } axsOspfIfMetricIpAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of this OSPF interface." ::= { axsOspfIfMetricEntry 2 } axsOspfIfMetricAddressLessIf OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the value of ifIndex for in- terfaces having no IP Address." ::= { axsOspfIfMetricEntry 3 } axsOspfIfMetricTOS OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The type of service metric being referenced. this value is only 0." ::= { axsOspfIfMetricEntry 4 } axsOspfIfMetricValue OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The metric of using this type of service on this interface." ::= { axsOspfIfMetricEntry 5 } axsOspfIfMetricStatus OBJECT-TYPE SYNTAX INTEGER { active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. This entry status is only valid(1)." ::= { axsOspfIfMetricEntry 6 } axsOspfVirtIfTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfVirtIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about this router's virtual interfaces." ::= { axsOspf 9 } axsOspfVirtIfEntry OBJECT-TYPE SYNTAX AxsOspfVirtIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a single Virtual Interface." INDEX { axsOspfVirtIfDomainNumber, axsOspfVirtIfAreaId, axsOspfVirtIfNeighbor } ::= { axsOspfVirtIfTable 1 } AxsOspfVirtIfEntry ::= SEQUENCE { axsOspfVirtIfDomainNumber INTEGER, axsOspfVirtIfAreaId IpAddress, axsOspfVirtIfNeighbor IpAddress, axsOspfVirtIfTransitDelay INTEGER, axsOspfVirtIfRetransInterval INTEGER, axsOspfVirtIfHelloInterval INTEGER, axsOspfVirtIfRtrDeadInterval INTEGER, axsOspfVirtIfState INTEGER, axsOspfVirtIfEvents Counter, axsOspfVirtIfAuthKey OCTET STRING, axsOspfVirtIfStatus INTEGER } axsOspfVirtIfDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The domain number for this Virtual Interface" ::= { axsOspfVirtIfEntry 1 } axsOspfVirtIfAreaId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Transit Area that the Virtual Link traverses." ::= { axsOspfVirtIfEntry 2 } axsOspfVirtIfNeighbor OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { axsOspfVirtIfEntry 3 } axsOspfVirtIfTransitDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The estimated number of seconds it takes to transmit a link- state update packet over this interface." ::= { axsOspfVirtIfEntry 4 } axsOspfVirtIfRetransInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface." ::= { axsOspfVirtIfEntry 5 } axsOspfVirtIfHelloInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. " ::= { axsOspfVirtIfEntry 6 } axsOspfVirtIfRtrDeadInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down." ::= { axsOspfVirtIfEntry 7 } axsOspfVirtIfState OBJECT-TYPE SYNTAX INTEGER { down (1), -- these use the same encoding pointToPoint (4) -- as the axsOspfIfTable } ACCESS read-only STATUS mandatory DESCRIPTION "OSPF virtual interface states." ::= { axsOspfVirtIfEntry 8 } axsOspfVirtIfEvents OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of state changes or error events on this Virtual Link" ::= { axsOspfVirtIfEntry 9 } axsOspfVirtIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Authentication key of this interface." ::= { axsOspfVirtIfEntry 10 } axsOspfVirtIfStatus OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. This entry is only valid(1)." ::= { axsOspfVirtIfEntry 11 } axsOspfNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfNbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of non-virtual neighbor information." ::= { axsOspf 10 } axsOspfNbrEntry OBJECT-TYPE SYNTAX AxsOspfNbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The information regarding a single neighbor." INDEX { axsOspfNbrDomainNumber, axsOspfNbrIpAddr, axsOspfNbrAddressLessIndex } ::= { axsOspfNbrTable 1 } AxsOspfNbrEntry ::= SEQUENCE { axsOspfNbrDomainNumber INTEGER, axsOspfNbrIpAddr IpAddress, axsOspfNbrAddressLessIndex INTEGER, axsOspfNbrRtrId IpAddress, axsOspfNbrOptions INTEGER, axsOspfNbrPriority INTEGER, axsOspfNbrState INTEGER, axsOspfNbrEvents Counter, axsOspfNbrLsRetransQLen Gauge, axsOspfNbmaNbrStatus INTEGER, axsOspfNbmaNbrPermanence INTEGER } axsOspfNbrDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "OSPF domain number of this neighbor." ::= { axsOspfNbrEntry 1 } axsOspfNbrIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address this neighbor is using in its IP Source Address." ::= { axsOspfNbrEntry 2 } axsOspfNbrAddressLessIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB." ::= { axsOspfNbrEntry 3 } axsOspfNbrRtrId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The integer uniquely identifying the neighboring router in the Autonomous System." ::= { axsOspfNbrEntry 4 } axsOspfNbrOptions OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders." ::= { axsOspfNbrEntry 5 } axsOspfNbrPriority OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The priority of this neighbor." ::= { axsOspfNbrEntry 6 } axsOspfNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } ACCESS read-only STATUS mandatory DESCRIPTION "The State of the relationship with this Neighbor." ::= { axsOspfNbrEntry 7 } axsOspfNbrEvents OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this neighbor relationship has changed state, or an error has occurred." ::= { axsOspfNbrEntry 8 } axsOspfNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The current length of the retransmission queue." ::= { axsOspfNbrEntry 9 } axsOspfNbmaNbrStatus OBJECT-TYPE SYNTAX INTEGER { active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. This entry value is only valid(1). And enable to response this entry when axsOspfIfType is nbma." ::= { axsOspfNbrEntry 10 } axsOspfNbmaNbrPermanence OBJECT-TYPE SYNTAX INTEGER { dynamic (1), -- learned through protocol permanent (2) -- configured address } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry." ::= { axsOspfNbrEntry 11 } axsOspfVirtNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfVirtNbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of virtual neighbor information." ::= { axsOspf 11 } axsOspfVirtNbrEntry OBJECT-TYPE SYNTAX AxsOspfVirtNbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Virtual neighbor information." INDEX { axsOspfVirtNbrDomainNumber, axsOspfVirtNbrArea, axsOspfVirtNbrRtrId } ::= { axsOspfVirtNbrTable 1 } AxsOspfVirtNbrEntry ::= SEQUENCE { axsOspfVirtNbrDomainNumber INTEGER, axsOspfVirtNbrArea IpAddress, axsOspfVirtNbrRtrId IpAddress, axsOspfVirtNbrIpAddr IpAddress, axsOspfVirtNbrOptions INTEGER, axsOspfVirtNbrState INTEGER, axsOspfVirtNbrEvents Counter, axsOspfVirtNbrLsRetransQLen Gauge } axsOspfVirtNbrDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The domain number." ::= { axsOspfVirtNbrEntry 1 } axsOspfVirtNbrArea OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Transit Area Identifier." ::= { axsOspfVirtNbrEntry 2 } axsOspfVirtNbrRtrId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "A integer uniquely identifying the neighboring router in the Autonomous System." ::= { axsOspfVirtNbrEntry 3 } axsOspfVirtNbrIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address this Virtual Neighbor is using." ::= { axsOspfVirtNbrEntry 4 } axsOspfVirtNbrOptions OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A Bit Mask corresponding to the neighbor's options field. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 2, if set, indicates that the system is Network Multicast capable; ie, that it implements OSPF Multicast Routing." ::= { axsOspfVirtNbrEntry 5 } axsOspfVirtNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the Virtual Neighbor Relationship." ::= { axsOspfVirtNbrEntry 6 } axsOspfVirtNbrEvents OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this virtual link has changed its state, or an error has occurred." ::= { axsOspfVirtNbrEntry 7 } axsOspfVirtNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The current length of the retransmission queue." ::= { axsOspfVirtNbrEntry 8 } axsOspfExtLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfExtLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The OSPF Process's Links State Database." ::= { axsOspf 12 } axsOspfExtLsdbEntry OBJECT-TYPE SYNTAX AxsOspfExtLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single Link State Advertisement." INDEX { axsOspfExtLsdbDomainNumber, axsOspfExtLsdbType, axsOspfExtLsdbLsid, axsOspfExtLsdbRouterId } ::= { axsOspfExtLsdbTable 1 } AxsOspfExtLsdbEntry ::= SEQUENCE { axsOspfExtLsdbDomainNumber INTEGER, axsOspfExtLsdbType INTEGER, axsOspfExtLsdbLsid IpAddress, axsOspfExtLsdbRouterId IpAddress, axsOspfExtLsdbSequence INTEGER, axsOspfExtLsdbAge INTEGER, axsOspfExtLsdbChecksum INTEGER, axsOspfExtLsdbAdvertisement OCTET STRING } axsOspfExtLsdbDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "OSPF domain number." ::= { axsOspfExtLsdbEntry 1 } axsOspfExtLsdbType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (5) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the link state advertisement." ::= { axsOspfExtLsdbEntry 2 } axsOspfExtLsdbLsid OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." ::= { axsOspfExtLsdbEntry 3 } axsOspfExtLsdbRouterId OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." ::= { axsOspfExtLsdbEntry 4 } axsOspfExtLsdbSequence OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The sequence number field is a signed 32-bit integer." ::= { axsOspfExtLsdbEntry 5 } axsOspfExtLsdbAge OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The age of the link state advertisement in seconds." ::= { axsOspfExtLsdbEntry 6 } axsOspfExtLsdbChecksum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum." ::= { axsOspfExtLsdbEntry 7 } axsOspfExtLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The entire Link State Advertisement, including its header." ::= { axsOspfExtLsdbEntry 8 } axsOspfAreaAggregateTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfAreaAggregateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A range of IP addresses specified by an IP address/IP network mask pair." ::= { axsOspf 14 } axsOspfAreaAggregateEntry OBJECT-TYPE SYNTAX AxsOspfAreaAggregateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A range of IP addresses specified by an IP address/IP network mask pair." INDEX { axsOspfAreaAggregateDomainNumber, axsOspfAreaAggregateAreaID, axsOspfAreaAggregateLsdbType, axsOspfAreaAggregateNet, axsOspfAreaAggregateMask } ::= { axsOspfAreaAggregateTable 1 } AxsOspfAreaAggregateEntry ::= SEQUENCE { axsOspfAreaAggregateDomainNumber INTEGER, axsOspfAreaAggregateAreaID IpAddress, axsOspfAreaAggregateLsdbType INTEGER, axsOspfAreaAggregateNet IpAddress, axsOspfAreaAggregateMask IpAddress, axsOspfAreaAggregateStatus INTEGER, axsOspfAreaAggregateEffect INTEGER } axsOspfAreaAggregateDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "OSPF domain number." ::= { axsOspfAreaAggregateEntry 1 } axsOspfAreaAggregateAreaID OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Area the Address Aggregate is to be found within." ::= { axsOspfAreaAggregateEntry 2 } axsOspfAreaAggregateLsdbType OBJECT-TYPE SYNTAX INTEGER { summaryLink (3), nssaExternalLink (7) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the Address Aggregate. This field specifies the Lsdb type that this Address Aggregate applies to." ::= { axsOspfAreaAggregateEntry 3 } axsOspfAreaAggregateNet OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP Address of the Net or Subnet indicated by the range." ::= { axsOspfAreaAggregateEntry 4 } axsOspfAreaAggregateMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Subnet Mask that pertains to the Net or Subnet." ::= { axsOspfAreaAggregateEntry 5 } axsOspfAreaAggregateStatus OBJECT-TYPE SYNTAX INTEGER { active(1) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the entry. This entry value is only valid(1)." ::= { axsOspfAreaAggregateEntry 6 } axsOspfAreaAggregateEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching (1), doNotAdvertiseMatching (2) } ACCESS read-only STATUS mandatory DESCRIPTION "Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area." ::= { axsOspfAreaAggregateEntry 7 } axsOspfTrapControlTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfTrapControlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table about trap information." ::= { axsOspfTrap 1 } axsOspfTrapControlEntry OBJECT-TYPE SYNTAX AxsOspfTrapControlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Entry about trap information." INDEX { axsOspfTrapDomainNumber } ::= { axsOspfTrapControlTable 1 } AxsOspfTrapControlEntry ::= SEQUENCE { axsOspfTrapDomainNumber INTEGER, axsOspfSetTrap OCTET STRING, axsOspfConfigErrorType INTEGER, axsOspfPacketType INTEGER, axsOspfPacketSrc IpAddress } axsOspfTrapDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "axsOspfTrap domain number." ::= { axsOspfTrapControlEntry 1 } axsOspfSetTrap OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "A four-octet string serving as a bit map for the trap events defined by the OSPF traps. This object is used to enable and disable specific OSPF traps where a 1 in the bit field represents enabled. The right-most bit (least significant) represents trap 0." ::= { axsOspfTrapControlEntry 2 } axsOspfConfigErrorType OBJECT-TYPE SYNTAX INTEGER { badVersion (1), areaMismatch (2), unknownNbmaNbr (3), -- Router is Dr eligible unknownVirtualNbr (4), authTypeMismatch(5), authFailure (6), netMaskMismatch (7), helloIntervalMismatch (8), deadIntervalMismatch (9), optionMismatch (10), duplicateRouterId (12), noError (13)} ACCESS read-only STATUS mandatory DESCRIPTION "Potential types of configuration conflicts. Used by the ospfConfigError and ospfConfigVir- tError traps." ::= { axsOspfTrapControlEntry 3 } axsOspfPacketType OBJECT-TYPE SYNTAX INTEGER { hello (1), dbDescript (2), lsReq (3), lsUpdate (4), lsAck (5), nullPacket (6)} ACCESS read-only STATUS mandatory DESCRIPTION "OSPF packet types." ::= { axsOspfTrapControlEntry 4 } axsOspfPacketSrc OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of an inbound packet that can- not be identified by a neighbor instance." ::= { axsOspfTrapControlEntry 5 } -- axsOspfv3 axsOspfv3GeneralTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3GeneralEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table which ospfv3 information is stored in." ::= { axsOspfv3 1 } axsOspfv3GeneralEntry OBJECT-TYPE SYNTAX AxsOspfv3GeneralEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The list of the ospfv3 information." INDEX { axsOspfv3GeneralDomainNumber } ::= { axsOspfv3GeneralTable 1 } AxsOspfv3GeneralEntry ::= SEQUENCE { axsOspfv3GeneralDomainNumber INTEGER, axsOspfv3RouterId RouterID, axsOspfv3AdminStat Status, axsOspfv3VersionNumber INTEGER, axsOspfv3AreaBdrRtrStatus TruthValue, axsOspfv3ASBdrRtrStatus TruthValue, axsOspfv3AsScopeLsaCount Gauge32, axsOspfv3AsScopeLsaCksumSum Integer32, axsOspfv3OriginateNewLsas Counter32, axsOspfv3RxNewLsas Counter32, axsOspfv3ExtAreaLsdbLimit Integer32, axsOspfv3MulticastExtensions Integer32, axsOspfv3DemandExtensions TruthValue, axsOspfv3TrafficEngineeringSupport TruthValue } axsOspfv3GeneralDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3GeneralEntry 1 } axsOspfv3RouterId OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IPv4 interface addresses if IPv4 is configured." ::= { axsOspfv3GeneralEntry 2 } axsOspfv3AdminStat OBJECT-TYPE SYNTAX Status ACCESS read-only STATUS mandatory DESCRIPTION "The administrative status of axsOspfv3 in the router. The value 'enabled' denotes that the axsOspfv3 Process is active on at least one inter- face; 'disabled' disables it on all inter- faces." ::= { axsOspfv3GeneralEntry 3 } axsOspfv3VersionNumber OBJECT-TYPE SYNTAX INTEGER { version3 (3) } ACCESS read-only STATUS mandatory DESCRIPTION "The version number of OSPF for IPv6 is 3." ::= { axsOspfv3GeneralEntry 4 } axsOspfv3AreaBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "A flag to note whether this router is an area border router." REFERENCE "OSPF Version 2, Section 3 Splitting the AS into Areas" ::= { axsOspfv3GeneralEntry 5 } axsOspfv3ASBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "A flag to note whether this router is config- ured as an Autonomous System border router." REFERENCE "OSPF Version 2, Section 3.3 Classification of routers" ::= { axsOspfv3GeneralEntry 6 } axsOspfv3AsScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of AS-Scope (e.g. AS-External) link-state advertisements in the link-state database." ::= { axsOspfv3GeneralEntry 7 } axsOspfv3AsScopeLsaCksumSum OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The 32-bit unsigned sum of the LS checksums of the AS-scoped link-state advertisements con- tained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." ::= { axsOspfv3GeneralEntry 8 } axsOspfv3OriginateNewLsas OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of new link-state advertisements that have been originated. This number is in- cremented each time the router originates a new LSA." ::= { axsOspfv3GeneralEntry 9 } axsOspfv3RxNewLsas OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of link-state advertisements re- ceived determined to be new instantiations. This number does not include newer instantia- tions of self-originated link-state advertise- ments." ::= { axsOspfv3GeneralEntry 10 } axsOspfv3ExtAreaLsdbLimit OBJECT-TYPE SYNTAX Integer32 (-1..'7FFFFFFF'h) ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches axsOspfv3ExtAreaLsdbLimit, the router enters Overflow- State. The router never holds more than axsOspfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. OspfExtAreaLsdbLimit MUST be set identically in all routers attached to the axsOspfv3 backbone and/or any regular axsOspfv3 area. (i.e., axsOspfv3 stub areas and NSSAs are excluded)." DEFVAL { -1 } ::= { axsOspfv3GeneralEntry 11 } axsOspfv3MulticastExtensions OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IPv6 multicast datagrams between axsOspfv3 areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IPv6 multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: 0 (no multicast forwarding is enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled." DEFVAL { 0 } ::= { axsOspfv3GeneralEntry 12 } axsOspfv3DemandExtensions OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "The router's support for demand routing." REFERENCE "OSPF Version 2, Appendix on Demand Routing" ::= { axsOspfv3GeneralEntry 14 } axsOspfv3TrafficEngineeringSupport OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "The router's support for traffic engineering extensions." ::= { axsOspfv3GeneralEntry 15 } -- The axsOspfv3 Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area axsOspfv3AreaTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3AreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of the router's attached areas." REFERENCE "OSPF Version 2, Section 6 The Area Data Struc- ture" ::= { axsOspfv3 2 } axsOspfv3AreaEntry OBJECT-TYPE SYNTAX AxsOspfv3AreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas." INDEX { axsOspfv3AreaDomainNumber, axsOspfv3AreaId } ::= { axsOspfv3AreaTable 1 } AxsOspfv3AreaEntry ::= SEQUENCE { axsOspfv3AreaDomainNumber INTEGER, axsOspfv3AreaId AreaID, axsOspfv3ImportAsExtern INTEGER, axsOspfv3SpfRuns Counter32, axsOspfv3AreaBdrRtrCount Gauge32, axsOspfv3AsBdrRtrCount Gauge32, axsOspfv3AreaScopeLsaCount Gauge32, axsOspfv3AreaScopeLsaCksumSum Integer32, axsOspfv3AreaSummary INTEGER, axsOspfv3AreaStatus RowStatus, axsOspfv3StubMetric BigMetric } axsOspfv3AreaDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3AreaEntry 1 } axsOspfv3AreaId OBJECT-TYPE SYNTAX AreaID ACCESS read-only STATUS mandatory DESCRIPTION "A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the axsOspfv3 backbone." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { axsOspfv3AreaEntry 2 } axsOspfv3ImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal (1), -- normal area importNoExternal (2), -- stub area importNssa (3) -- not-so-stubby-area } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as Type-7 LSAs which have Area-scope" REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" DEFVAL { importExternal } ::= { axsOspfv3AreaEntry 3 } axsOspfv3SpfRuns OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm." ::= { axsOspfv3AreaEntry 4 } axsOspfv3AreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass." ::= { axsOspfv3AreaEntry 5 } axsOspfv3AsBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass." ::= { axsOspfv3AreaEntry 6 } axsOspfv3AreaScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Area-Scope link-state advertisements in this area's link-state database." ::= { axsOspfv3AreaEntry 7 } axsOspfv3AreaScopeLsaCksumSum OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The 32-bit unsigned sum of the Area-Scope link-state advertisements' LS checksums contained in this area's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { axsOspfv3AreaEntry 8 } axsOspfv3AreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary (1), sendAreaSummary (2) } ACCESS read-only STATUS mandatory DESCRIPTION "The variable axsOspfv3AreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs." DEFVAL { noAreaSummary } ::= { axsOspfv3AreaEntry 9 } axsOspfv3AreaStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { axsOspfv3AreaEntry 10 } axsOspfv3StubMetric OBJECT-TYPE SYNTAX BigMetric -- ACCESS read-create ACCESS read-only STATUS mandatory DESCRIPTION "The metric value advertised for the default route into Stub and NSSA areas." ::= { axsOspfv3AreaEntry 11 } -- axsOspfv3 AS-Scope Link State Database -- The Link State Database contains the AS-Scope Link State -- Advertisements from throughout the areas that the -- device is attached to. axsOspfv3AsLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3AsLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The axsOspfv3 Process's AS-Scope Link State Database." ::= { axsOspfv3 3 } axsOspfv3AsLsdbEntry OBJECT-TYPE SYNTAX AxsOspfv3AsLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single AS-Scope Link State Advertisement." INDEX { axsOspfv3AsLsdbDomainNumber, axsOspfv3AsLsdbType, axsOspfv3AsLsdbRouterId, axsOspfv3AsLsdbLsid } ::= { axsOspfv3AsLsdbTable 1 } AxsOspfv3AsLsdbEntry ::= SEQUENCE { axsOspfv3AsLsdbDomainNumber INTEGER, axsOspfv3AsLsdbType INTEGER, axsOspfv3AsLsdbRouterId RouterID, axsOspfv3AsLsdbLsid IpAddress, axsOspfv3AsLsdbSequence Integer32, axsOspfv3AsLsdbAge Integer32, axsOspfv3AsLsdbChecksum Integer32, axsOspfv3AsLsdbAdvertisement OCTET STRING } axsOspfv3AsLsdbDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3AsLsdbEntry 1 } axsOspfv3AsLsdbType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (16389) -- 0x4005 } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format. Unrecognized AS-Scope LSAs with the U-bit set are also store in this database." ::= { axsOspfv3AsLsdbEntry 2 } axsOspfv3AsLsdbRouterId OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { axsOspfv3AsLsdbEntry 3 } axsOspfv3AsLsdbLsid OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPF for IPv4, the LSID has no addressing semantics." ::= { axsOspfv3AsLsdbEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. axsOspfv3AsLsdbSequence OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { axsOspfv3AsLsdbEntry 5 } axsOspfv3AsLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge ACCESS read-only STATUS mandatory DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { axsOspfv3AsLsdbEntry 6 } axsOspfv3AsLsdbChecksum OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { axsOspfv3AsLsdbEntry 7 } axsOspfv3AsLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) ACCESS read-only STATUS mandatory DESCRIPTION "The entire Link State Advertisement, including its header." ::= { axsOspfv3AsLsdbEntry 8 } -- axsOspfv3 Area-Scope Link State Database -- The Link State Database contains the Area-Scope Link State -- Advertisements from throughout the area that the -- device is attached to. axsOspfv3AreaLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3AreaLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The axsOspfv3 Process's Area-Scope Link State Database." ::= { axsOspfv3 4 } axsOspfv3AreaLsdbEntry OBJECT-TYPE SYNTAX AxsOspfv3AreaLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single Area-Scope Link State Advertisement." INDEX { axsOspfv3AreaLsdbDomainNumber, axsOspfv3AreaLsdbAreaId, axsOspfv3AreaLsdbType, axsOspfv3AreaLsdbRouterId, axsOspfv3AreaLsdbLsid } ::= { axsOspfv3AreaLsdbTable 1 } AxsOspfv3AreaLsdbEntry ::= SEQUENCE { axsOspfv3AreaLsdbDomainNumber INTEGER, axsOspfv3AreaLsdbAreaId AreaID, axsOspfv3AreaLsdbType INTEGER, axsOspfv3AreaLsdbRouterId RouterID, axsOspfv3AreaLsdbLsid IpAddress, axsOspfv3AreaLsdbSequence Integer32, axsOspfv3AreaLsdbAge Integer32, axsOspfv3AreaLsdbChecksum Integer32, axsOspfv3AreaLsdbAdvertisement OCTET STRING } axsOspfv3AreaLsdbDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3AreaLsdbEntry 1 } axsOspfv3AreaLsdbAreaId OBJECT-TYPE SYNTAX AreaID ACCESS read-only STATUS mandatory DESCRIPTION "The 32 bit identifier of the Area from which the LSA was received." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters." ::= { axsOspfv3AreaLsdbEntry 2 } axsOspfv3AreaLsdbType OBJECT-TYPE SYNTAX INTEGER { routerLsa (8193), -- 0x2001 networkLsa (8194), -- 0x2002 interAreaPrefixLsa (8195), -- 0x2003 interAreaRouterLsa (8196), -- 0x2004 groupMembershipLsa (8198), -- 0x2006 nssaExternalLsa (8199), -- 0x2007 intraAreaPrefixLsa (8201) -- 0x2009 } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format. Unrecognized Area-Scope LSAs with the U-bit set are also stored in this database." ::= { axsOspfv3AreaLsdbEntry 3 } axsOspfv3AreaLsdbRouterId OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { axsOspfv3AreaLsdbEntry 4 } axsOspfv3AreaLsdbLsid OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPF for IPv4, the LSID has no addressing semantics." ::= { axsOspfv3AreaLsdbEntry 5 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. axsOspfv3AreaLsdbSequence OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { axsOspfv3AreaLsdbEntry 6 } axsOspfv3AreaLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge ACCESS read-only STATUS mandatory DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { axsOspfv3AreaLsdbEntry 7 } axsOspfv3AreaLsdbChecksum OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { axsOspfv3AreaLsdbEntry 8 } axsOspfv3AreaLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) ACCESS read-only STATUS mandatory DESCRIPTION "The entire Link State Advertisement, including its header." ::= { axsOspfv3AreaLsdbEntry 9 } -- axsOspfv3 Link-Scope Link State Database -- The Link State Database contains the Link-Scope Link State -- Advertisements from the links that the -- device is attached to. axsOspfv3LinkLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3LinkLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The axsOspfv3 Process's Link-Scope Link State Database." ::= { axsOspfv3 5 } axsOspfv3LinkLsdbEntry OBJECT-TYPE SYNTAX AxsOspfv3LinkLsdbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A single Link-Scope Link State Advertisement." INDEX { axsOspfv3LinkLsdbDomainNumber, axsOspfv3LinkLsdbIfIndex, axsOspfv3LinkLsdbType, axsOspfv3LinkLsdbRouterId, axsOspfv3LinkLsdbLsid } ::= { axsOspfv3LinkLsdbTable 1 } AxsOspfv3LinkLsdbEntry ::= SEQUENCE { axsOspfv3LinkLsdbDomainNumber INTEGER, axsOspfv3LinkLsdbIfIndex Ipv6IfIndex, axsOspfv3LinkLsdbType INTEGER, axsOspfv3LinkLsdbRouterId RouterID, axsOspfv3LinkLsdbLsid IpAddress, axsOspfv3LinkLsdbSequence Integer32, axsOspfv3LinkLsdbAge Integer32, axsOspfv3LinkLsdbChecksum Integer32, axsOspfv3LinkLsdbAdvertisement OCTET STRING } axsOspfv3LinkLsdbDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3LinkLsdbEntry 1 } axsOspfv3LinkLsdbIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex ACCESS read-only STATUS mandatory DESCRIPTION "The identifier of the link from which the LSA was received." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { axsOspfv3LinkLsdbEntry 2 } axsOspfv3LinkLsdbType OBJECT-TYPE SYNTAX INTEGER { linkLsa (8) -- 0x0008 } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format. Unrecognized Link-Scope LSAs with the U-bit set are also stored in this database." ::= { axsOspfv3LinkLsdbEntry 3 } axsOspfv3LinkLsdbRouterId OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { axsOspfv3LinkLsdbEntry 4 } axsOspfv3LinkLsdbLsid OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPF for IPv4, the LSID has no addressing semantics." ::= { axsOspfv3LinkLsdbEntry 5 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. axsOspfv3LinkLsdbSequence OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { axsOspfv3LinkLsdbEntry 6 } axsOspfv3LinkLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge ACCESS read-only STATUS mandatory DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { axsOspfv3LinkLsdbEntry 7 } axsOspfv3LinkLsdbChecksum OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { axsOspfv3LinkLsdbEntry 8 } axsOspfv3LinkLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) ACCESS read-only STATUS mandatory DESCRIPTION "The entire Link State Advertisement, including its header." ::= { axsOspfv3LinkLsdbEntry 9 } -- OSPF Host Table -- The Host/Metric Table indicates what hosts are directly -- attached to the Router, and what metrics and types of -- service should be advertised for them. -- axsOspfv3 Interface Table axsOspfv3IfTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The axsOspfv3 Interface Table describes the inter- faces from the viewpoint of axsOspfv3." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" ::= { axsOspfv3 7 } axsOspfv3IfEntry OBJECT-TYPE SYNTAX AxsOspfv3IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The axsOspfv3 Interface Entry describes one inter- face from the viewpoint of axsOspfv3." INDEX { axsOspfv3IfDomainNumber, axsOspfv3IfIndex } ::= { axsOspfv3IfTable 1 } AxsOspfv3IfEntry ::= SEQUENCE { axsOspfv3IfDomainNumber INTEGER, axsOspfv3IfIndex Ipv6IfIndex, axsOspfv3IfAreaId AreaID, axsOspfv3IfType INTEGER, axsOspfv3IfAdminStat Status, axsOspfv3IfRtrPriority DesignatedRouterPriority, axsOspfv3IfTransitDelay UpToMaxAge, axsOspfv3IfRetransInterval UpToMaxAge, axsOspfv3IfHelloInterval HelloRange, axsOspfv3IfRtrDeadInterval PositiveInteger, axsOspfv3IfPollInterval PositiveInteger, axsOspfv3IfState INTEGER, axsOspfv3IfDesignatedRouter RouterID, axsOspfv3IfBackupDesignatedRouter RouterID, axsOspfv3IfEvents Counter32, axsOspfv3IfStatus RowStatus, axsOspfv3IfMulticastForwarding INTEGER, axsOspfv3IfDemand TruthValue, axsOspfv3IfMetricValue Metric, axsOspfv3IfLinkScopeLsaCount Gauge32, axsOspfv3IfLinkLsaCksumSum Integer32, axsOspfv3IfInstId Integer32 } axsOspfv3IfDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3IfEntry 1 } axsOspfv3IfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex ACCESS read-only STATUS mandatory DESCRIPTION "The interface index of this axsOspfv3 interface. It corresponds to the interface index of the Ipv6 interface on which axsOspfv3 is configured." ::= { axsOspfv3IfEntry 2 } axsOspfv3IfAreaId OBJECT-TYPE SYNTAX AreaID ACCESS read-only STATUS mandatory DESCRIPTION "A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the axsOspfv3 backbone." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { axsOspfv3IfEntry 3 } axsOspfv3IfType OBJECT-TYPE SYNTAX INTEGER { broadcast (1), nbma (2), pointToPoint (3), pointToMultipoint (5) } ACCESS read-only STATUS mandatory DESCRIPTION "The axsOspfv3 interface type." ::= { axsOspfv3IfEntry 4 } axsOspfv3IfAdminStat OBJECT-TYPE SYNTAX Status ACCESS read-only STATUS mandatory DESCRIPTION "The axsOspfv3 interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to axsOspfv3." DEFVAL { enabled } ::= { axsOspfv3IfEntry 5 } axsOspfv3IfRtrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority ACCESS read-only STATUS mandatory DESCRIPTION "The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker." DEFVAL { 1 } ::= { axsOspfv3IfEntry 6 } axsOspfv3IfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge ACCESS read-only STATUS mandatory DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." DEFVAL { 1 } ::= { axsOspfv3IfEntry 7 } axsOspfv3IfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets." DEFVAL { 5 } ::= { axsOspfv3IfEntry 8 } axsOspfv3IfHelloInterval OBJECT-TYPE SYNTAX HelloRange ACCESS read-only STATUS mandatory DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network." DEFVAL { 10 } ::= { axsOspfv3IfEntry 9 } axsOspfv3IfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network." DEFVAL { 40 } ::= { axsOspfv3IfEntry 10 } axsOspfv3IfPollInterval OBJECT-TYPE SYNTAX PositiveInteger ACCESS read-only STATUS mandatory DESCRIPTION "The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor." DEFVAL { 120 } ::= { axsOspfv3IfEntry 11 } axsOspfv3IfState OBJECT-TYPE SYNTAX INTEGER { down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) } ACCESS read-only STATUS mandatory DESCRIPTION "The axsOspfv3 Interface State." DEFVAL { down } ::= { axsOspfv3IfEntry 12 } axsOspfv3IfDesignatedRouter OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "The Router ID of the Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { axsOspfv3IfEntry 13 } axsOspfv3IfBackupDesignatedRouter OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "The Router ID of the Backup Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { axsOspfv3IfEntry 15 } axsOspfv3IfEvents OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this OSPF interface has changed its state, or an error has occurred." ::= { axsOspfv3IfEntry 16 } axsOspfv3IfStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { axsOspfv3IfEntry 18 } axsOspfv3IfMulticastForwarding OBJECT-TYPE SYNTAX INTEGER { blocked (1), -- no multicast forwarding multicast (2), -- using multicast address unicast (3) -- to each axsOspfv3 neighbor } ACCESS read-only STATUS mandatory DESCRIPTION "The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting axsOspfv3MulticastForwarding to 0 effective- ly disables all multicast forwarding." DEFVAL { blocked } ::= { axsOspfv3IfEntry 19 } axsOspfv3IfDemand OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether Demand axsOspfv3 procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface." DEFVAL { false } ::= { axsOspfv3IfEntry 20 } axsOspfv3IfMetricValue OBJECT-TYPE SYNTAX Metric ACCESS read-only STATUS mandatory DESCRIPTION "The metric assigned to this interface. The default value of the Metric is 10^8 / ifSpeed." ::= { axsOspfv3IfEntry 21 } axsOspfv3IfLinkScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Link-Scope link-state advertisements in this link's link-state database." ::= { axsOspfv3IfEntry 22 } axsOspfv3IfLinkLsaCksumSum OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { axsOspfv3IfEntry 23 } axsOspfv3IfInstId OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "Enables multiple instances of axsOspfv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only." DEFVAL { 0 } ::= { axsOspfv3IfEntry 24 } -- axsOspfv3 Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the axsOspfv3 Process is configured to -- carry on. axsOspfv3VirtIfTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3VirtIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about this router's virtual inter- faces." REFERENCE "OSPF Version 2, Appendix C.4 Virtual link parameters" ::= { axsOspfv3 8 } axsOspfv3VirtIfEntry OBJECT-TYPE SYNTAX AxsOspfv3VirtIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a single Virtual Interface." INDEX { axsOspfv3VirtIfDomainNumber, axsOspfv3VirtIfAreaId, axsOspfv3VirtIfNeighbor } ::= { axsOspfv3VirtIfTable 1 } AxsOspfv3VirtIfEntry ::= SEQUENCE { axsOspfv3VirtIfDomainNumber INTEGER, axsOspfv3VirtIfAreaId AreaID, axsOspfv3VirtIfNeighbor RouterID, axsOspfv3VirtIfIndex Ipv6IfIndex, axsOspfv3VirtIfTransitDelay UpToMaxAge, axsOspfv3VirtIfRetransInterval UpToMaxAge, axsOspfv3VirtIfHelloInterval HelloRange, axsOspfv3VirtIfRtrDeadInterval PositiveInteger, axsOspfv3VirtIfState INTEGER, axsOspfv3VirtIfEvents Counter32, axsOspfv3VirtIfStatus RowStatus, axsOspfv3VirtIfLinkScopeLsaCount Gauge32, axsOspfv3VirtIfLinkLsaCksumSum Integer32 } axsOspfv3VirtIfDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3VirtIfEntry 1 } axsOspfv3VirtIfAreaId OBJECT-TYPE SYNTAX AreaID ACCESS read-only STATUS mandatory DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0" ::= { axsOspfv3VirtIfEntry 2 } axsOspfv3VirtIfNeighbor OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { axsOspfv3VirtIfEntry 3 } axsOspfv3VirtIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex ACCESS read-only STATUS mandatory DESCRIPTION "The interface index of this axsOspfv3 virtual interface. It must be unique among all the interface indices on the router." ::= { axsOspfv3VirtIfEntry 4 } axsOspfv3VirtIfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge ACCESS read-only STATUS mandatory DESCRIPTION "The estimated number of seconds it takes to transmit a link- state update packet over this interface." DEFVAL { 1 } ::= { axsOspfv3VirtIfEntry 5 } axsOspfv3VirtIfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time." DEFVAL { 5 } ::= { axsOspfv3VirtIfEntry 6 } axsOspfv3VirtIfHelloInterval OBJECT-TYPE SYNTAX HelloRange ACCESS read-only STATUS mandatory DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { axsOspfv3VirtIfEntry 7 } axsOspfv3VirtIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger ACCESS read-only STATUS mandatory DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor." DEFVAL { 60 } ::= { axsOspfv3VirtIfEntry 8 } axsOspfv3VirtIfState OBJECT-TYPE SYNTAX INTEGER { down (1), -- these use the same encoding pointToPoint (4) -- as the axsOspfv3IfTable } ACCESS read-only STATUS mandatory DESCRIPTION "OSPF virtual interface states." DEFVAL { down } ::= { axsOspfv3VirtIfEntry 9 } axsOspfv3VirtIfEvents OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of state changes or error events on this Virtual Link" ::= { axsOspfv3VirtIfEntry 10 } axsOspfv3VirtIfStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { axsOspfv3VirtIfEntry 11 } axsOspfv3VirtIfLinkScopeLsaCount OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Link-Scope link-state advertisements in this virtual link's link-state database." ::= { axsOspfv3VirtIfEntry 12 } axsOspfv3VirtIfLinkLsaCksumSum OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." DEFVAL { 0 } ::= { axsOspfv3VirtIfEntry 13 } -- axsOspfv3 Neighbor Table -- The axsOspfv3 Neighbor Table describes all neighbors in -- the locality of the subject router. axsOspfv3NbrTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3NbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of non-virtual neighbor information." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" ::= { axsOspfv3 9 } axsOspfv3NbrEntry OBJECT-TYPE SYNTAX AxsOspfv3NbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The information regarding a single neighbor." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" INDEX { axsOspfv3NbrDomainNumber, axsOspfv3NbrIfIndex, axsOspfv3NbrIpv6Addr } ::= { axsOspfv3NbrTable 1 } AxsOspfv3NbrEntry ::= SEQUENCE { axsOspfv3NbrDomainNumber INTEGER, axsOspfv3NbrIfIndex Ipv6IfIndex, axsOspfv3NbrIpv6Addr Ipv6Address, axsOspfv3NbrRtrId RouterID, axsOspfv3NbrOptions Integer32, axsOspfv3NbrPriority DesignatedRouterPriority, axsOspfv3NbrState INTEGER, axsOspfv3NbrEvents Counter32, axsOspfv3NbrLsRetransQLen Gauge32, axsOspfv3NbrHelloSuppressed TruthValue, axsOspfv3NbrIfId Ipv6IfIndex } axsOspfv3NbrDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3NbrEntry 1 } axsOspfv3NbrIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex ACCESS read-only STATUS mandatory DESCRIPTION "The local link ID of the link over which the neighbor can be reached." ::= { axsOspfv3NbrEntry 2 } axsOspfv3NbrIpv6Addr OBJECT-TYPE SYNTAX Ipv6Address ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 address of the neighbor associated with the local link." ::= { axsOspfv3NbrEntry 3 } axsOspfv3NbrRtrId OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System." ::= { axsOspfv3NbrEntry 4 } axsOspfv3NbrOptions OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field." DEFVAL { 0 } ::= { axsOspfv3NbrEntry 5 } axsOspfv3NbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority ACCESS read-only STATUS mandatory DESCRIPTION "The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network." DEFVAL { 1 } ::= { axsOspfv3NbrEntry 6 } axsOspfv3NbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } ACCESS read-only STATUS mandatory DESCRIPTION "The State of the relationship with this Neigh- bor." REFERENCE "OSPF Version 2, Section 10.1 Neighbor States" DEFVAL { down } ::= { axsOspfv3NbrEntry 7 } axsOspfv3NbrEvents OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this neighbor relationship has changed state, or an error has occurred." ::= { axsOspfv3NbrEntry 8 } axsOspfv3NbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The current length of the retransmission queue." ::= { axsOspfv3NbrEntry 9 } axsOspfv3NbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { axsOspfv3NbrEntry 12 } axsOspfv3NbrIfId OBJECT-TYPE SYNTAX Ipv6IfIndex ACCESS read-only STATUS mandatory DESCRIPTION "The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index." ::= { axsOspfv3NbrEntry 13 } -- axsOspfv3 Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. axsOspfv3VirtNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3VirtNbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table of virtual neighbor information." REFERENCE "OSPF Version 2, Section 15 Virtual Links" ::= { axsOspfv3 10 } axsOspfv3VirtNbrEntry OBJECT-TYPE SYNTAX AxsOspfv3VirtNbrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Virtual neighbor information." INDEX { axsOspfv3VirtNbrDomainNumber, axsOspfv3VirtNbrArea, axsOspfv3VirtNbrRtrId } ::= { axsOspfv3VirtNbrTable 1 } AxsOspfv3VirtNbrEntry ::= SEQUENCE { axsOspfv3VirtNbrDomainNumber INTEGER, axsOspfv3VirtNbrArea AreaID, axsOspfv3VirtNbrRtrId RouterID, axsOspfv3VirtNbrIfIndex Ipv6IfIndex, axsOspfv3VirtNbrIpv6Addr Ipv6Address, axsOspfv3VirtNbrOptions Integer32, axsOspfv3VirtNbrState INTEGER, axsOspfv3VirtNbrEvents Counter32, axsOspfv3VirtNbrLsRetransQLen Gauge32, axsOspfv3VirtNbrHelloSuppressed TruthValue, axsOspfv3VirtNbrIfId Ipv6IfIndex } axsOspfv3VirtNbrDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3VirtNbrEntry 1 } axsOspfv3VirtNbrArea OBJECT-TYPE SYNTAX AreaID ACCESS read-only STATUS mandatory DESCRIPTION "The Transit Area Identifier." ::= { axsOspfv3VirtNbrEntry 2 } axsOspfv3VirtNbrRtrId OBJECT-TYPE SYNTAX RouterID ACCESS read-only STATUS mandatory DESCRIPTION "A 32-bit integer uniquely identifying the neighboring router in the Autonomous System." ::= { axsOspfv3VirtNbrEntry 3 } axsOspfv3VirtNbrIfIndex OBJECT-TYPE SYNTAX Ipv6IfIndex ACCESS read-only STATUS mandatory DESCRIPTION "The local link ID for the virtual link over which the neighbor can be reached." ::= { axsOspfv3VirtNbrEntry 4 } axsOspfv3VirtNbrIpv6Addr OBJECT-TYPE SYNTAX Ipv6Address ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 address used to reach this Virtual Neighbor. It must be a Site-Local or Global scope address." ::= { axsOspfv3VirtNbrEntry 5 } axsOspfv3VirtNbrOptions OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field." ::= { axsOspfv3VirtNbrEntry 6 } axsOspfv3VirtNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the Virtual Neighbor Relation- ship." ::= { axsOspfv3VirtNbrEntry 7 } axsOspfv3VirtNbrEvents OBJECT-TYPE SYNTAX Counter32 ACCESS read-only STATUS mandatory DESCRIPTION "The number of times this virtual link has changed its state, or an error has occurred." ::= { axsOspfv3VirtNbrEntry 8 } axsOspfv3VirtNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 ACCESS read-only STATUS mandatory DESCRIPTION "The current length of the retransmission queue." ::= { axsOspfv3VirtNbrEntry 9 } axsOspfv3VirtNbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue ACCESS read-only STATUS mandatory DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { axsOspfv3VirtNbrEntry 10 } axsOspfv3VirtNbrIfId OBJECT-TYPE SYNTAX Ipv6IfIndex ACCESS read-only STATUS mandatory DESCRIPTION "The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface index." ::= { axsOspfv3VirtNbrEntry 11 } -- -- The axsOspfv3 Area Aggregate Table -- axsOspfv3AreaAggregateTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsOspfv3AreaAggregateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range sub- sumes another range the most specific match is the preferred one." ::= { axsOspfv3 11 } axsOspfv3AreaAggregateEntry OBJECT-TYPE SYNTAX AxsOspfv3AreaAggregateEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range sub- sumes another range the most specific match is the preferred one." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" INDEX { axsOspfv3AreaAggregateDomainNumber, axsOspfv3AreaAggregateAreaID, axsOspfv3AreaAggregateAreaLsdbType, axsOspfv3AreaAggregateIndex } ::= { axsOspfv3AreaAggregateTable 1 } AxsOspfv3AreaAggregateEntry ::= SEQUENCE { axsOspfv3AreaAggregateDomainNumber INTEGER, axsOspfv3AreaAggregateAreaID AreaID, axsOspfv3AreaAggregateAreaLsdbType INTEGER, axsOspfv3AreaAggregateIndex INTEGER, axsOspfv3AreaAggregatePrefix Ipv6AddressPrefix, axsOspfv3AreaAggregatePrefixLen INTEGER, axsOspfv3AreaAggregateStatus RowStatus, axsOspfv3AreaAggregateEffect INTEGER } axsOspfv3AreaAggregateDomainNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ospfv3 domain number." ::= { axsOspfv3AreaAggregateEntry 1 } axsOspfv3AreaAggregateAreaID OBJECT-TYPE SYNTAX AreaID ACCESS read-only STATUS mandatory DESCRIPTION "The Area the Address Aggregate is to be found within." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { axsOspfv3AreaAggregateEntry 2 } axsOspfv3AreaAggregateAreaLsdbType OBJECT-TYPE SYNTAX INTEGER { interAreaPrefixLsa (8195), -- 0x2003 nssaExternalLsa (8199) -- 0x2007 } ACCESS read-only STATUS mandatory DESCRIPTION "The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Ag- gregate applies to." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { axsOspfv3AreaAggregateEntry 3 } axsOspfv3AreaAggregateIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "A unique identifier for this aggregate table entry." ::= { axsOspfv3AreaAggregateEntry 4 } axsOspfv3AreaAggregatePrefix OBJECT-TYPE SYNTAX Ipv6AddressPrefix ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 Prefix." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { axsOspfv3AreaAggregateEntry 5 } axsOspfv3AreaAggregatePrefixLen OBJECT-TYPE SYNTAX INTEGER ( 3..128 ) -- UNITS "bits" ACCESS read-only STATUS mandatory DESCRIPTION "The length of the prefix (in bits). A prefix can not be shorter than 3 bits." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { axsOspfv3AreaAggregateEntry 6 } axsOspfv3AreaAggregateStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { axsOspfv3AreaAggregateEntry 7 } axsOspfv3AreaAggregateEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching (1), doNotAdvertiseMatching (2) } ACCESS read-only STATUS mandatory DESCRIPTION "Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the prefix not being advertised at all outside the area." DEFVAL { advertiseMatching } ::= { axsOspfv3AreaAggregateEntry 8 } -- axsStatic axsStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsStaticGatewayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The set of instances of the static gateway state." ::= { axsStatic 1 } axsStaticGatewayEntry OBJECT-TYPE SYNTAX AxsStaticGatewayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each row defines information about static route gateway state." INDEX { axsStaticGatewayAddr } ::= { axsStaticTable 1 } AxsStaticGatewayEntry ::= SEQUENCE { axsStaticGatewayAddr IpAddress, axsStaticGatewayState INTEGER } axsStaticGatewayAddr OBJECT-TYPE SYNTAX IpAddress ACCESS not-accessible STATUS mandatory DESCRIPTION "The static route gateway address." ::= { axsStaticGatewayEntry 1 } axsStaticGatewayState OBJECT-TYPE SYNTAX INTEGER { reachable(1), unreachable(2) } ACCESS not-accessible STATUS mandatory DESCRIPTION "The state of static route gateway." ::= { axsStaticGatewayEntry 2 } axsStaticIpv6Table OBJECT-TYPE SYNTAX SEQUENCE OF AxsStaticIpv6GatewayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The set of instances of the ipv6 static gateway state." ::= { axsStatic 3 } axsStaticIpv6GatewayEntry OBJECT-TYPE SYNTAX AxsStaticIpv6GatewayEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each row defines information about ipv6 static route gateway state." INDEX { axsStaticIpv6Ifindex, axsStaticIpv6GatewayAddr } ::= { axsStaticIpv6Table 1 } AxsStaticIpv6GatewayEntry ::= SEQUENCE { axsStaticIpv6Ifindex INTEGER, axsStaticIpv6GatewayAddr Ipv6Address, axsStaticIpv6GatewayState INTEGER } axsStaticIpv6Ifindex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The ifIndex related static gateway address." ::= { axsStaticIpv6GatewayEntry 1 } axsStaticIpv6GatewayAddr OBJECT-TYPE SYNTAX Ipv6Address ACCESS not-accessible STATUS mandatory DESCRIPTION "The static route gateway address." ::= { axsStaticIpv6GatewayEntry 2 } axsStaticIpv6GatewayState OBJECT-TYPE SYNTAX INTEGER { reachable(1), unreachable(2) } ACCESS not-accessible STATUS mandatory DESCRIPTION "The state of static route gateway." ::= { axsStaticIpv6GatewayEntry 3 } -- axsUlr axsUlrID OBJECT-TYPE SYNTAX MacAddress ACCESS read-only STATUS mandatory DESCRIPTION "Identifier of device." ::= { axsUlrGlobalInfo 2 } axsUlrConfigurationPortCounts OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of primary port and secondary port in device." ::= { axsUlrGlobalInfo 3 } axsUlrStartupActivePortSelection OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The configuration of startup active port selection." ::= { axsUlrGlobalInfo 4 } axsUlrPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsUlrPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing uplink port information." ::= { axsUlr 2 } axsUlrPortEntry OBJECT-TYPE SYNTAX AxsUlrPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing uplink port." INDEX { axsUlrPortIfIndex } ::= { axsUlrPortTable 1 } AxsUlrPortEntry ::= SEQUENCE { axsUlrPortIfIndex INTEGER, axsUlrPortType INTEGER, axsUlrPairedPortIfIndex INTEGER, axsUlrPortStatus INTEGER, axsUlrPairedPortStatus INTEGER, axsUlrAutoChangeToPrimary INTEGER, axsUlrAutoChangeToPrimaryDelay INTEGER, axsUlrAutoChangeToPrimaryRest INTEGER, axsUlrStartupActivePortSelectionStatus INTEGER, axsUlrFlushTransmit INTEGER, axsUlrFlushVlan INTEGER, axsUlrMacAddressUpdateTransmit INTEGER, axsUlrLastActivePortDecisionTime TimeStamp, axsUlrLastFlushTransmitTime TimeStamp, axsUlrLastMacUpdateTransmitTime TimeStamp, axsUlrLastChangeFactor INTEGER, axsUlrFlushTransmitTotalPackets INTEGER, axsUlrMacAddressUpdateTransmitTotalPackets INTEGER, axsUlrMacAddressUpdateTransmitOverFlow INTEGER, axsUlrActiveDecisionCount INTEGER } axsUlrPortIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "IfIndex of the port." ::= { axsUlrPortEntry 1 } axsUlrPortType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Type of port. 1) Primary 2) Secondary" ::= { axsUlrPortEntry 2 } axsUlrPairedPortIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "IfIndex of paired port." ::= { axsUlrPortEntry 3 } axsUlrPortStatus OBJECT-TYPE SYNTAX INTEGER { forwarding(1), down(2), blocking(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of port. 1) Forwarding 2) Down 3) Blocking" ::= { axsUlrPortEntry 4 } axsUlrPairedPortStatus OBJECT-TYPE SYNTAX INTEGER { forwarding(1), down(2), blocking(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of paired port. 1) Forwarding 2) Down 3) Blocking" ::= { axsUlrPortEntry 5 } axsUlrAutoChangeToPrimary OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The configuration of preemption. 1) Off 2) On" ::= { axsUlrPortEntry 6 } axsUlrAutoChangeToPrimaryDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Delay time of preemption." ::= { axsUlrPortEntry 7 } axsUlrAutoChangeToPrimaryRest OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The rest time of preemption." ::= { axsUlrPortEntry 8 } axsUlrStartupActivePortSelectionStatus OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of startup active port selection. 1) Off 2) On" ::= { axsUlrPortEntry 9 } axsUlrFlushTransmit OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The configuration of transmit flush-request frame. 1) Off 2) On" ::= { axsUlrPortEntry 10 } axsUlrFlushVlan OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The transmit VLAN ID in flush-request frame. 0 is not configuration." ::= { axsUlrPortEntry 11 } axsUlrMacAddressUpdateTransmit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of transmit MAC Address update frame in one opportunity." ::= { axsUlrPortEntry 12 } axsUlrLastActivePortDecisionTime OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "Last determinate time of the active port." ::= { axsUlrPortEntry 13 } axsUlrLastFlushTransmitTime OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "Last transmit time of flush-request frame." ::= { axsUlrPortEntry 14 } axsUlrLastMacUpdateTransmitTime OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "Last transmit time of MAC Address update frame." ::= { axsUlrPortEntry 15 } axsUlrLastChangeFactor OBJECT-TYPE SYNTAX INTEGER { command(1), configure(2), primary-down(3), primary-up(4), secondary-down(5), secondary-up(6), preemption(7) } ACCESS read-only STATUS mandatory DESCRIPTION "Last determinate factor of the active port. 1) command 2) configure 3) primary down 4) primary up 5) secondary down 6) secondary up 7) preemption" ::= { axsUlrPortEntry 16 } axsUlrFlushTransmitTotalPackets OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total number of transmit flush-request frame in the port." ::= { axsUlrPortEntry 17 } axsUlrMacAddressUpdateTransmitTotalPackets OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total number of transmit MAC Address update frame in the port." ::= { axsUlrPortEntry 18 } axsUlrMacAddressUpdateTransmitOverFlow OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The over flow number of MAC Address update frame." ::= { axsUlrPortEntry 19 } axsUlrActiveDecisionCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The determinate number of active port in uplink port." ::= { axsUlrPortEntry 20 } -- axsTrackObject axsTrackObjectGeneralLastChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The last time that the tracking object state changed." ::= { axsTrackObjectGeneralGroup 1 } axsTrackObjectTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsTrackObjectEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table containing the tracking information." ::= { axsTrackObject 3 } axsTrackObjectEntry OBJECT-TYPE SYNTAX AxsTrackObjectEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of track information." INDEX { axsTrackObjectId } ::= { axsTrackObjectTable 1 } AxsTrackObjectEntry ::= SEQUENCE { axsTrackObjectId INTEGER, axsTrackObjectState INTEGER, axsTrackObjectOperation INTEGER, axsTrackObjectType INTEGER, axsTrackObjectNetIndex INTEGER } axsTrackObjectId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unique index number given for each track-object settings." ::= { axsTrackObjectEntry 1 } axsTrackObjectState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the track." ::= { axsTrackObjectEntry 2 } axsTrackObjectOperation OBJECT-TYPE SYNTAX INTEGER { active(1), transit(2), disabled(3), init(4), aging(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The operation state of the track." ::= { axsTrackObjectEntry 3 } axsTrackObjectType OBJECT-TYPE SYNTAX INTEGER { ipv4-icmp(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The tracking type of the track." ::= { axsTrackObjectEntry 4 } axsTrackObjectNetIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The network ID of the ICMP tracking object." ::= { axsTrackObjectEntry 5 } -- axsPolicyBase axsPolicyBaseRoutingChangeListNumber OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "List number change is generated by policy base routing." ::= { axsPolicyBaseRouting 1 } axsPolicyBaseRoutingChangeSequenceNumber OBJECT-TYPE SYNTAX Unsigned32 ACCESS not-accessible STATUS mandatory DESCRIPTION "Priority changed by the list number of the policy base routing." ::= { axsPolicyBaseRouting 2 } -- axsLogin axsLoginName OBJECT-TYPE SYNTAX DisplayString ACCESS not-accessible STATUS mandatory DESCRIPTION "Log in user name." ::= { axsLogin 1 } axsLoginTime OBJECT-TYPE SYNTAX DisplayString ACCESS not-accessible STATUS mandatory DESCRIPTION "Date, time and time zone of user log in. Format : YYYY/MM/DD hh:mm:ss XXXXXX(time zone) Time zone format : JST : JST GMT+09 : GMT + 09 hours GMT+10 : GMT + 10 hours" ::= { axsLogin 2 } axsLogoutTime OBJECT-TYPE SYNTAX DisplayString ACCESS not-accessible STATUS mandatory DESCRIPTION "Date, time and time zone of user log out. Format : YYYY/MM/DD hh:mm:ss XXXXXX(time zone) Time zone format : JST : JST GMT+09 : GMT + 09 hours GMT+10 : GMT + 10 hours" ::= { axsLogin 3 } axsLoginFailureTime OBJECT-TYPE SYNTAX DisplayString ACCESS not-accessible STATUS mandatory DESCRIPTION "Date, time and time zone of user log in failure. Format : YYYY/MM/DD hh:mm:ss XXXXXX(time zone) Time zone format : JST : JST GMT+09 : GMT + 09 hours GMT+10 : GMT + 10 hours" ::= { axsLogin 4 } axsLoginLocation OBJECT-TYPE SYNTAX DisplayString ACCESS not-accessible STATUS mandatory DESCRIPTION "Terminal information of log in user. The status will be 'console' or 'aux'. If other, displays 'TERMINAL(APLLICATION)'. ex. 'tty/1(telnet)'" ::= { axsLogin 5 } axsLoginLine OBJECT-TYPE SYNTAX DisplayString ACCESS not-accessible STATUS mandatory DESCRIPTION "Connection information of log in user. The status will be 'console' or 'aux'. If other, displays 'IPADDRESS(APLLICATION)'. ex. '192.168.11.1(telnet)'" ::= { axsLogin 6 } axsLogoutStatus OBJECT-TYPE SYNTAX INTEGER { error(1), success(2), timeout(3), disconnect(4), force(5) } ACCESS not-accessible STATUS mandatory DESCRIPTION "Log out factor. error(1) : log out due to none of bellow success(2) : log out due to command timeout(3) : log out due to 'auto-logout' disconnect(4) : log out due to line disconnection force(5) : log out due to other user's command" ::= { axsLogin 7 } -- axsAxrp group axsAxrpGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsAxrpGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing AXRP group information." ::= { axsAxrp 1 } axsAxrpGroupEntry OBJECT-TYPE SYNTAX AxsAxrpGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The list of AXRP group information." INDEX { axsAxrpGroupRingId } ::= { axsAxrpGroupTable 1 } AxsAxrpGroupEntry ::= SEQUENCE { axsAxrpGroupRingId INTEGER, axsAxrpGroupRowStatus RowStatus, axsAxrpGroupMode INTEGER, axsAxrpGroupRingAttribute INTEGER, axsAxrpGroupMonitoringState INTEGER, axsAxrpGroupRingport1 INTEGER, axsAxrpGroupRingport1Shared INTEGER, axsAxrpGroupRingport2 INTEGER, axsAxrpGroupRingport2Shared INTEGER, axsAxrpGroupTransitionToFaultCounts Counter, axsAxrpGroupTransitionToNormalCounts Counter, axsAxrpGroupLastTransitionTime TimeStamp, axsAxrpGroupLinkStatusAlert INTEGER, axsAxrpGroupRingport1LinkKeepaliveSend INTEGER, axsAxrpGroupRingport1LinkKeepaliveMonitor INTEGER, axsAxrpGroupRingport1LinkState INTEGER, axsAxrpGroupRingport1LinkKeepaliveReceiveCounts Counter, axsAxrpGroupRingport2LinkKeepaliveSend INTEGER, axsAxrpGroupRingport2LinkKeepaliveMonitor INTEGER, axsAxrpGroupRingport2LinkState INTEGER, axsAxrpGroupRingport2LinkKeepaliveReceiveCounts Counter, axsAxrpGroupMultiFaultDetectionState INTEGER } axsAxrpGroupRingId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "AXRP group ring identifier." ::= { axsAxrpGroupEntry 1 } axsAxrpGroupRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "Valid/Invalid state of this entry. Valid(1) fixed" ::= { axsAxrpGroupEntry 2 } axsAxrpGroupMode OBJECT-TYPE SYNTAX INTEGER{ no-config(1), master(2), transit(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Operation mode of each ring ID." ::= { axsAxrpGroupEntry 3 } axsAxrpGroupRingAttribute OBJECT-TYPE SYNTAX INTEGER{ no-config(1), rift-ring(2), rift-ring-edge1(3), rift-ring-edge2(4) } ACCESS read-only STATUS mandatory DESCRIPTION "When the multi ring is composed, it is an attribute of this device in the common link non-watch ring. " ::= { axsAxrpGroupEntry 4 } axsAxrpGroupMonitoringState OBJECT-TYPE SYNTAX INTEGER{ init(1), disable(2), fault-monitoring(3), recovery-monitoring(4), flush-monitoring(5), not-operating(6), suppress-fault-recovery(7), preempt-delay(8), recovery-re-monitoring(9) } ACCESS read-only STATUS mandatory DESCRIPTION "Operation and state of watch of ring. " ::= { axsAxrpGroupEntry 5 } axsAxrpGroupRingport1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "IfIndex of ring port 1 (port in one where Ifindex is small)" ::= { axsAxrpGroupEntry 6 } axsAxrpGroupRingport1Shared OBJECT-TYPE SYNTAX INTEGER { no-config(1), shared-edge(2), shared(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Ring port 1 is common port information. " ::= { axsAxrpGroupEntry 7 } axsAxrpGroupRingport2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "IfIndex of ring port 2 (port in one where Ifindex is large)" ::= { axsAxrpGroupEntry 8 } axsAxrpGroupRingport2Shared OBJECT-TYPE SYNTAX INTEGER { no-config(1), shared-edge(2), shared(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Ring port 2 is common port information." ::= { axsAxrpGroupEntry 9 } axsAxrpGroupTransitionToFaultCounts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Frequency that shifts from state of trouble watch in state of restoration watch. " ::= { axsAxrpGroupEntry 10 } axsAxrpGroupTransitionToNormalCounts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Frequency that shifts from state of restoration watch in state of trouble watch. " ::= { axsAxrpGroupEntry 11 } axsAxrpGroupLastTransitionTime OBJECT-TYPE SYNTAX TimeStamp ACCESS read-only STATUS mandatory DESCRIPTION "It is changing the final time to restoration from the trouble or the trouble from restoration. " ::= { axsAxrpGroupEntry 12 } axsAxrpGroupLinkStatusAlert OBJECT-TYPE SYNTAX INTEGER { no-config(1), enable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "State of each ring ID of link trouble detection." ::= { axsAxrpGroupEntry 13 } axsAxrpGroupRingport1LinkKeepaliveSend OBJECT-TYPE SYNTAX INTEGER { no-config(1), enable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "State of transmission of link trouble watch frame of ring port 1." ::= { axsAxrpGroupEntry 14 } axsAxrpGroupRingport1LinkKeepaliveMonitor OBJECT-TYPE SYNTAX INTEGER { no-config(1), enable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "State of link trouble watch of ring port 1. " ::= { axsAxrpGroupEntry 15 } axsAxrpGroupRingport1LinkState OBJECT-TYPE SYNTAX INTEGER { not-monitoring(1), normal(2), fault(3) } ACCESS read-only STATUS mandatory DESCRIPTION "State of link of ring port 1." ::= { axsAxrpGroupEntry 16 } axsAxrpGroupRingport1LinkKeepaliveReceiveCounts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of reception frames of link state watch frames of ring port 1. " ::= { axsAxrpGroupEntry 17 } axsAxrpGroupRingport2LinkKeepaliveSend OBJECT-TYPE SYNTAX INTEGER { no-config(1), enable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "State of transmission of link trouble watch frame of ring port 2." ::= { axsAxrpGroupEntry 18 } axsAxrpGroupRingport2LinkKeepaliveMonitor OBJECT-TYPE SYNTAX INTEGER { no-config(1), enable(2) } ACCESS read-only STATUS mandatory DESCRIPTION "State of link trouble watch of ring port 2." ::= { axsAxrpGroupEntry 19 } axsAxrpGroupRingport2LinkState OBJECT-TYPE SYNTAX INTEGER { not-monitoring(1), normal(2), fault(3) } ACCESS read-only STATUS mandatory DESCRIPTION "State of link of ring port 2." ::= { axsAxrpGroupEntry 20 } axsAxrpGroupRingport2LinkKeepaliveReceiveCounts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of reception frames of link state watch frames of ring port 2. " ::= { axsAxrpGroupEntry 21 } axsAxrpGroupMultiFaultDetectionState OBJECT-TYPE SYNTAX INTEGER { not-monitoring(1), normal(2), fault(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Operation and state of multiple fault detection of ring." ::= { axsAxrpGroupEntry 22 } axsAxrpVlanGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsAxrpVlanGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing AXRP VLAN group information." ::= { axsAxrp 2 } axsAxrpVlanGroupEntry OBJECT-TYPE SYNTAX AxsAxrpVlanGroupEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The list of AXRP VLAN group information." INDEX { axsAxrpVlanGroupRingId, axsAxrpVlanGroupId } ::= { axsAxrpVlanGroupTable 1 } AxsAxrpVlanGroupEntry ::= SEQUENCE { axsAxrpVlanGroupRingId INTEGER, axsAxrpVlanGroupId INTEGER, axsAxrpVlanGroupRingport1 INTEGER, axsAxrpVlanGroupRingport1Role INTEGER, axsAxrpVlanGroupRingport1OperState INTEGER, axsAxrpVlanGroupRingport2 INTEGER, axsAxrpVlanGroupRingport2Role INTEGER, axsAxrpVlanGroupRingport2OperState INTEGER } axsAxrpVlanGroupRingId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "AXRP VLAN ring group number(1~65535)" ::= { axsAxrpVlanGroupEntry 1 } axsAxrpVlanGroupId OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "AXRP VLAN group number(1~8)" ::= { axsAxrpVlanGroupEntry 2 } axsAxrpVlanGroupRingport1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "IfIndex of ring port 1 (port in one where Ifindex is small)" ::= { axsAxrpVlanGroupEntry 3 } axsAxrpVlanGroupRingport1Role OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2), other(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Role of ring port 1" ::= { axsAxrpVlanGroupEntry 4 } axsAxrpVlanGroupRingport1OperState OBJECT-TYPE SYNTAX INTEGER { forwarding(1), blocking(2), other(3), down(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Present of ring port 1" ::= { axsAxrpVlanGroupEntry 5 } axsAxrpVlanGroupRingport2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "IfIndex of ring port 2 (port in one where Ifindex is small)" ::= { axsAxrpVlanGroupEntry 6 } axsAxrpVlanGroupRingport2Role OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2), other(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Role of ring port 2" ::= { axsAxrpVlanGroupEntry 7 } axsAxrpVlanGroupRingport2OperState OBJECT-TYPE SYNTAX INTEGER { forwarding(1), blocking(2), other(3), down(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Present of ring port 2" ::= { axsAxrpVlanGroupEntry 8 } -- axsBootManagement group axsBootReason OBJECT-TYPE SYNTAX INTEGER { power-on(1), reload(2), system-fault(3), system-stall(4), reset(5), fail-over(6), default-restart(7), wake-on-rtc(9), wake-on-reset(10) } ACCESS read-only STATUS mandatory DESCRIPTION "Reason of system start." ::= { axsBootManagement 1 } -- axslldp group -- axslldpConfiguration group axslldpMessageTxInterval OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "LDPDU transmitting interval" ::= { axslldpConfiguration 1 } axslldpMessageTxHoldMultiplier OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Time coefficient for contiguity equipment to hold about the LLDP frame which this equipment transmitted" ::= { axslldpConfiguration 2 } axslldpPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF AxslldpPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table about LDPDU transmission" ::= { axslldpConfiguration 6 } axslldpPortConfigEntry OBJECT-TYPE SYNTAX AxslldpPortConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry about LDPDU transmission" INDEX { axslldpPortConfigPortNum } ::= { axslldpPortConfigTable 1 } AxslldpPortConfigEntry ::= SEQUENCE { axslldpPortConfigPortNum INTEGER, axslldpPortConfigAdminStatus INTEGER, axslldpPortConfigTLVsTxEnable BITS, axslldpPortConfigRowStatus RowStatus } axslldpPortConfigPortNum OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Port discernment index" ::= {axslldpPortConfigEntry 2 } axslldpPortConfigAdminStatus OBJECT-TYPE SYNTAX INTEGER { txOnly(1), rxOnly(2), txAndRx(3), disabled(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The port state of this equipment about transmission and reception of LDPDU" ::= {axslldpPortConfigEntry 3 } axslldpPortConfigTLVsTxEnable OBJECT-TYPE SYNTAX BITS{ portDesc(4), sysName(5), sysDesc(6), sysCap(7) } ACCESS read-only STATUS mandatory DESCRIPTION "The TLV state about the port concerned which can be transmitted" ::= {axslldpPortConfigEntry 4 } axslldpPortConfigRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-only STATUS mandatory DESCRIPTION "The state of this entry" ::= {axslldpPortConfigEntry 5 } -- axslldpStats group axslldpStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AxslldpStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table about LLDP statistics information" ::= { axslldpStats 1 } axslldpStatsEntry OBJECT-TYPE SYNTAX AxslldpStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Entry about LLDP statistics information" INDEX { axslldpStatsPortNum } ::= { axslldpStatsTable 1 } AxslldpStatsEntry ::= SEQUENCE { axslldpStatsPortNum INTEGER, axslldpStatsOperStatus INTEGER, axslldpStatsFramesInErrors Counter, axslldpStatsFramesInTotal Counter, axslldpStatsFramesOutTotal Counter, axslldpStatsTLVsInErrors Counter, axslldpStatsTLVsDiscardedTotal Counter } axslldpStatsPortNum OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Port discernment index" ::= {axslldpStatsEntry 2 } axslldpStatsOperStatus OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The employment state about the port concerned" ::= {axslldpStatsEntry 3 } axslldpStatsFramesInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of inaccurate LDPDU reception about the port concerned" ::= {axslldpStatsEntry 4 } axslldpStatsFramesInTotal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of LDPDU reception about the port concerned" ::= {axslldpStatsEntry 5 } axslldpStatsFramesOutTotal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of LDPDU transmission about the port concerned" ::= {axslldpStatsEntry 6 } axslldpStatsTLVsInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of inaccurate TLV reception about the port concerned" ::= {axslldpStatsEntry 7 } axslldpStatsTLVsDiscardedTotal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total abandonment TLV number about the port concerned" ::= {axslldpStatsEntry 8 } -- axslldpLocalSystemData group axslldpLocChassisType OBJECT-TYPE SYNTAX INTEGER { entPhysicalAlias(1), ifAlias(2), portEntPhysicalAlias(3), backplaneEntPhysicalAlias(4), macAddress(5), networkAddress(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The chassis type about this equipment" ::= {axslldpLocalSystemData 1 } axslldpLocChassisId OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The chassis ID about this equipment" ::= {axslldpLocalSystemData 2 } axslldpLocSysName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The system name about this equipment" ::= {axslldpLocalSystemData 3 } axslldpLocSysDesc OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "System information about this equipment" ::= {axslldpLocalSystemData 4 } axslldpLocPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AxslldpLocPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table about the port of this equipment" ::= { axslldpLocalSystemData 7 } axslldpLocPortEntry OBJECT-TYPE SYNTAX AxslldpLocPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry about the port of this equipment" INDEX { axslldpLocPortNum } ::= { axslldpLocPortTable 1 } AxslldpLocPortEntry ::= SEQUENCE { axslldpLocPortNum INTEGER, axslldpLocPortType INTEGER, axslldpLocPortId OCTET STRING, axslldpLocPortDesc OCTET STRING } axslldpLocPortNum OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Port discernment index" ::= {axslldpLocPortEntry 1 } axslldpLocPortType OBJECT-TYPE SYNTAX INTEGER { ifAlias(1), portEntPhysicalAlias(2), backplaneEntPhysicalAlias(3), macAddress(4), networkAddress(5), local(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The port type about the port concerned of this equipment" ::= {axslldpLocPortEntry 2 } axslldpLocPortId OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The port ID about the port concerned of this equipment" ::= {axslldpLocPortEntry 3 } axslldpLocPortDesc OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Port information about the port concerned of this equipment" ::= {axslldpLocPortEntry 4 } -- axslldpRemoteSystemData group axslldpRemTable OBJECT-TYPE SYNTAX SEQUENCE OF AxslldpRemEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table about contiguity equipment" ::= { axslldpRemoteSystemData 1 } axslldpRemEntry OBJECT-TYPE SYNTAX AxslldpRemEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry about contiguity equipment" INDEX { axslldpRemLocalPortNum,axslldpRemIndex } ::= { axslldpRemTable 1 } AxslldpRemEntry ::= SEQUENCE { axslldpRemLocalPortNum INTEGER, axslldpRemIndex INTEGER, axslldpRemRemoteChassisType INTEGER, axslldpRemRemoteChassis OCTET STRING, axslldpRemRemotePortType INTEGER, axslldpRemRemotePort OCTET STRING, axslldpRemPortDesc OCTET STRING, axslldpRemSysName OCTET STRING, axslldpRemSysDesc OCTET STRING } axslldpRemLocalPortNum OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The discernment index of the port of this equipment which received the information about contiguity equipment" ::= {axslldpRemEntry 2 } axslldpRemIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The index about contiguity equipment" ::= {axslldpRemEntry 3 } axslldpRemRemoteChassisType OBJECT-TYPE SYNTAX INTEGER { entPhysicalAlias(1), ifAlias(2), portEntPhysicalAlias(3), backplaneEntPhysicalAlias(4), macAddress(5), networkAddress(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The chassis type about contiguity equipment" ::= {axslldpRemEntry 4 } axslldpRemRemoteChassis OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The chassis ID about contiguity equipment" ::= {axslldpRemEntry 5 } axslldpRemRemotePortType OBJECT-TYPE SYNTAX INTEGER { ifAlias(1), portEntPhysicalAlias(2), backplaneEntPhysicalAlias(3), macAddress(4), networkAddress(5), local(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The port type about the port concerned of contiguity equipment" ::= {axslldpRemEntry 6 } axslldpRemRemotePort OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The port ID about the port concerned of contiguity equipment" ::= {axslldpRemEntry 7 } axslldpRemPortDesc OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Information about the port concerned of contiguity equipment" ::= {axslldpRemEntry 8 } axslldpRemSysName OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The system name about contiguity equipment" ::= {axslldpRemEntry 9 } axslldpRemSysDesc OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "System information about contiguity equipment" ::= {axslldpRemEntry 10 } axslldpRemOriginInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF AxslldpRemOriginInfoEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table about original with AlaxalA networks TLV of contiguity equipment" ::= { axslldpRemoteOriginInfoData 1 } axslldpRemOriginInfoEntry OBJECT-TYPE SYNTAX AxslldpRemOriginInfoEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry about original with AlaxalA networks TLV of contiguity equipment" INDEX { axslldpRemOriginInfoPortNum,axslldpRemOriginInfoIndex } ::= { axslldpRemOriginInfoTable 1 } AxslldpRemOriginInfoEntry ::= SEQUENCE { axslldpRemOriginInfoPortNum INTEGER, axslldpRemOriginInfoIndex INTEGER, axslldpRemOriginInfoLowerVlanList OCTET STRING, axslldpRemOriginInfoHigherVlanList OCTET STRING, axslldpRemOriginInfoIPv4Address OCTET STRING, axslldpRemOriginInfoIPv4PortType INTEGER, axslldpRemOriginInfoIPv4VlanId INTEGER, axslldpRemOriginInfoIPv6Address OCTET STRING, axslldpRemOriginInfoIPv6PortType INTEGER, axslldpRemOriginInfoIPv6VlanId INTEGER } axslldpRemOriginInfoPortNum OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The discernment index of the port of this equipment which received the information about contiguity equipment." ::= {axslldpRemOriginInfoEntry 1 } axslldpRemOriginInfoIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The index about contiguity equipment" ::= {axslldpRemOriginInfoEntry 2 } axslldpRemOriginInfoLowerVlanList OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "What expressed effective VLAN ID by the bit map by VLAN 1-2047 in the port concerned of contiguity equipment" ::= {axslldpRemOriginInfoEntry 3 } axslldpRemOriginInfoHigherVlanList OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "What expressed effective VLAN ID by the bit map by VLAN 2048-4095 in the port concerned of contiguity equipment" ::= {axslldpRemOriginInfoEntry 4 } axslldpRemOriginInfoIPv4Address OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "IPv4 address given to the port concerned of contiguity equipment" ::= {axslldpRemOriginInfoEntry 5 } axslldpRemOriginInfoIPv4PortType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Port classification of the port of contiguity equipment concerned" ::= {axslldpRemOriginInfoEntry 6 } axslldpRemOriginInfoIPv4VlanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The smallest thing among VLAN ID to which IPv4 address is given" ::= {axslldpRemOriginInfoEntry 7 } axslldpRemOriginInfoIPv6Address OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The IPv6 address given to the port concerned of contiguity equipment" ::= {axslldpRemOriginInfoEntry 8 } axslldpRemOriginInfoIPv6PortType OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Port classification of the port of contiguity equipment concerned" ::= {axslldpRemOriginInfoEntry 9 } axslldpRemOriginInfoIPv6VlanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The smallest thing among VLAN ID to which the IPv6 address is given" ::= {axslldpRemOriginInfoEntry 10 } -- axsPconMIB group -- axsPconModuleData group axsPconModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsPconModuleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing electric power control information of module." ::= { axsPconModuleData 1 } axsPconModuleEntry OBJECT-TYPE SYNTAX AxsPconModuleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing electric power control information of module." INDEX { axsPconModuleIndex } ::= { axsPconModuleTable 1 } AxsPconModuleEntry ::= SEQUENCE { axsPconModuleIndex Integer32, axsPconModuleType INTEGER, axsPconModuleSlotNo Integer32, axsPconModuleDescr DisplayString, axsPconModuleStatus INTEGER, axsPconModuleMode INTEGER } axsPconModuleIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) ACCESS not-accessible STATUS mandatory DESCRIPTION "A unique value for each module contained by the network device." ::= { axsPconModuleEntry 1 } axsPconModuleType OBJECT-TYPE SYNTAX INTEGER { all(1), chassis(2), bcu(3), csu(4), msu(5), bsu(6), nif(7) } ACCESS read-only STATUS mandatory DESCRIPTION "An indication of the type of module." ::= { axsPconModuleEntry 2 } axsPconModuleSlotNo OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "Position information of the module slots." ::= { axsPconModuleEntry 3 } axsPconModuleDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The textual description of module." ::= { axsPconModuleEntry 4 } axsPconModuleStatus OBJECT-TYPE SYNTAX INTEGER { unsupported(-1), disconnected(0), active(1), standby(2), down(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The module status of this axsPconModuleEntry." ::= { axsPconModuleEntry 5 } axsPconModuleMode OBJECT-TYPE SYNTAX INTEGER { unsupported(-1), other(0), normal(1), saving-mode1(2), saving-mode2(3), saving(4), changing(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The module mode of this axsPconModuleEntry." ::= { axsPconModuleEntry 6 } -- axsPconPowerCon group axsPconPowerConTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsPconPowerConEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The power consumption information table." ::= { axsPconPowerCon 1 } axsPconPowerConEntry OBJECT-TYPE SYNTAX AxsPconPowerConEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The power consumption information entry." INDEX { axsPconModuleIndex } ::= { axsPconPowerConTable 1 } AxsPconPowerConEntry ::= SEQUENCE { axsPconPowerConMaxPower Gauge, axsPconPowerConPowerConsumption Counter64, axsPconPowerConPowerMeter Gauge } axsPconPowerConMaxPower OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The maximum electric power of module." ::= { axsPconPowerConEntry 1 } axsPconPowerConPowerConsumption OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The power consumption of module." ::= { axsPconPowerConEntry 2 } axsPconPowerConPowerMeter OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The power meter of module." ::= { axsPconPowerConEntry 3 } -- axsPconTraffic group axsPconTrafficTable OBJECT-TYPE SYNTAX SEQUENCE OF AxsPconTrafficEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Traffic information table." ::= { axsPconTraffic 1 } axsPconTrafficEntry OBJECT-TYPE SYNTAX AxsPconTrafficEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Traffic information entry." INDEX { axsPconModuleIndex } ::= { axsPconTrafficTable 1 } AxsPconTrafficEntry ::= SEQUENCE { axsPconTrafficMaxTransferCapacity Gauge, axsPconTrafficTotalTransferCapacity Gauge, axsPconTrafficInOctets Counter64, axsPconTrafficOutOctets Counter64, axsPconTrafficInPkts Counter64, axsPconTrafficOutPkts Counter64, axsPconTrafficCapacityOctets Counter64, axsPconTrafficInPeakOctetsRate Gauge, axsPconTrafficPeakTransferCapacity Gauge, axsPconTrafficInDiscPkts Counter64 } axsPconTrafficMaxTransferCapacity OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The maximum transfer capacity." ::= { axsPconTrafficEntry 1 } axsPconTrafficTotalTransferCapacity OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The total transfer capacity." ::= { axsPconTrafficEntry 2 } axsPconTrafficInOctets OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets that received on this module." ::= { axsPconTrafficEntry 3 } axsPconTrafficOutOctets OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets transmitted out from this module." ::= { axsPconTrafficEntry 4 } axsPconTrafficInPkts OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets that received on this module." ::= { axsPconTrafficEntry 5 } axsPconTrafficOutPkts OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets transmitted out from this module." ::= { axsPconTrafficEntry 6 } axsPconTrafficCapacityOctets OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The accumulation octets capacity that can be received on this module." ::= { axsPconTrafficEntry 7 } axsPconTrafficInPeakOctetsRate OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The peak rate of octets that received on this module." ::= { axsPconTrafficEntry 8 } axsPconTrafficPeakTransferCapacity OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The rate of margin when incoming traffic is peak." ::= { axsPconTrafficEntry 9 } axsPconTrafficInDiscPkts OBJECT-TYPE SYNTAX Counter64 ACCESS read-only STATUS mandatory DESCRIPTION "The total number of discarded packets on this module." ::= { axsPconTrafficEntry 10 } -- ax3630sSwitch group ax3630sModelType OBJECT-TYPE SYNTAX INTEGER { other(1), model-AX3630S-24T(500), model-AX3630S-24T2X(501), model-AX3630S-24P(502), model-AX3630S-48TW(506), model-AX3630S-48T2XW(507), model-AX3630S-24S2XW(508) } ACCESS read-only STATUS mandatory DESCRIPTION "Model type of this system." ::= { ax3630sSwitch 1 } --ax3630sSoftware OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "Software information of this system." -- ::= { ax3630sSwitch 2 } ax3630sSoftwareName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Software name of this system." ::= { ax3630sSoftware 1 } ax3630sSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..35)) ACCESS read-only STATUS mandatory DESCRIPTION "System software abbreviation." ::= { ax3630sSoftware 2 } ax3630sSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "System software version." ::= { ax3630sSoftware 3 } --ax3630sSystemMsg OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "System messege group." -- ::= { ax3630sSwitch 3 } ax3630sSystemMsgText OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) ACCESS read-only STATUS mandatory DESCRIPTION "The text of the system log message.For information about this code, see: Operator's Manual. " ::= { ax3630sSystemMsg 1 } ax3630sSystemMsgType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The event type. For information about this code, see: Operator's Manual." ::= { ax3630sSystemMsg 2 } ax3630sSystemMsgTimeStamp OBJECT-TYPE SYNTAX DisplayString (SIZE (0..14)) ACCESS read-only STATUS mandatory DESCRIPTION "The time that event occured. And that is expressed as type of MM/DD hh:mm:ss MM:month(01-12) DD:day(01-31) hh:hour(00-23) mm:minute(00-59) ss:second(00-59) Insert space between DD and hh." ::= { ax3630sSystemMsg 3 } ax3630sSystemMsgLevel OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The newest system message log level.For information about this code, see: Operator's Manual. " ::= { ax3630sSystemMsg 4 } ax3630sSystemMsgEventPoint OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The code of part that system message error occured. For information about this code,see: Operator's Manual. " ::= { ax3630sSystemMsg 5 } ax3630sSystemMsgEventInterfaceID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..40)) ACCESS read-only STATUS mandatory DESCRIPTION "Interface identification of system messages. For information about this code,see: Operator's Manual." ::= { ax3630sSystemMsg 6 } ax3630sSystemMsgEventCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "Event kind code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3630sSystemMsg 7 } ax3630sSystemMsgAdditionalCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "Additional code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3630sSystemMsg 8 } --ax3630sSnmpAgent OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "Related information of SNMP agent." -- ::= { ax3630sSwitch 4 } ax3630sSnmpSendReceiveSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SNMP packet data size in Manager-to-Agent communication. The value is displayed in bytes." ::= { ax3630sSnmpAgent 1 } ax3630sSnmpReceiveDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A recommendable interval to receive packets from Manager.The value is displayed in milliseconds." ::= { ax3630sSnmpAgent 2 } ax3630sSnmpContinuousSend OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of times that is recommendable continuous transmission packets." ::= { ax3630sSnmpAgent 3 } ax3630sSnmpObjectMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of objects that contain SNMP packet." ::= { ax3630sSnmpAgent 4 } --ax3630sSerialNumber OBJECT-TYPE -- SYNTAX DisplayString (SIZE (0..30)) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "Management information (SerialNumber) of RMP2-CARD." -- ::= { ax3630sSwitch 5 } ax3630sLicenseNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of the configured license serial numbers." ::= { ax3630sLicense 1 } ax3630sLicenseTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing the license information." ::= { ax3630sLicense 2 } ax3630sLicenseEntry OBJECT-TYPE SYNTAX Ax3630sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of license information." INDEX { ax3630sLicenseIndex } ::= { ax3630sLicenseTable 1 } Ax3630sLicenseTableEntry ::= SEQUENCE { ax3630sLicenseIndex INTEGER, ax3630sLicenseSerialNumber DisplayString, ax3630sLicenseOptionNumber INTEGER } ax3630sLicenseIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The number is from 1 to ax3630sLicenseNumber." ::= { ax3630sLicenseEntry 1 } ax3630sLicenseSerialNumber OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The serial number." ::= { ax3630sLicenseEntry 2 } ax3630sLicenseOptionNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of option licenses associated with the serial number." ::= { ax3630sLicenseEntry 3 } ax3630sLicenseOptionTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing option licenses information associated with the serial number." ::= { ax3630sLicense 3 } ax3630sLicenseOptionEntry OBJECT-TYPE SYNTAX Ax3630sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of the option license information associated with the serial number." INDEX { ax3630sLicenseOptionIndex,ax3630sLicenseOptionNumberIndex } ::= { ax3630sLicenseOptionTable 1 } Ax3630sLicenseOptionTableEntry ::= SEQUENCE { ax3630sLicenseOptionIndex INTEGER, ax3630sLicenseOptionNumberIndex INTEGER, ax3630sLicenseOptionSoftwareName DisplayString, ax3630sLicenseOptionSoftwareAbbreviation DisplayString } ax3630sLicenseOptionIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The same number as ax3630sLicenseIndex." ::= { ax3630sLicenseOptionEntry 1 } ax3630sLicenseOptionNumberIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number of option licenses information which is given for each serial number. The number is from 1 to ax3630sLicenseNumber." ::= { ax3630sLicenseOptionEntry 2 } ax3630sLicenseOptionSoftwareName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software model name of the option license information associated with the serial number." ::= { ax3630sLicenseOptionEntry 3 } ax3630sLicenseOptionSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software abbreviated name of the option license information associated with the serial number. " ::= { ax3630sLicenseOptionEntry 4 } -- ax3630sDevice group ax3630sChassisMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of cluster chassis that can connect to this router." ::= { ax3630sChassis 1 } ax3630sChassisTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing chassis information." ::= { ax3630sChassis 2 } ax3630sChassisEntry OBJECT-TYPE SYNTAX Ax3630sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing specific chassis." INDEX { ax3630sChassisIndex } ::= { ax3630sChassisTable 1 } Ax3630sChassisTableEntry ::= SEQUENCE { ax3630sChassisIndex INTEGER, ax3630sChassisType INTEGER, ax3630sChassisStatus INTEGER, ax3630sStsLedStatus INTEGER, ax3630sCpuName DisplayString, ax3630sCpuClock INTEGER, ax3630sMemoryTotalSize INTEGER, ax3630sMemoryUsedSize INTEGER, ax3630sMemoryFreeSize INTEGER, ax3630sRomVersion DisplayString, ax3630sCpuLoad1m INTEGER, ax3630sFlashTotalSize INTEGER, ax3630sFlashUsedSize INTEGER, ax3630sFlashFreeSize INTEGER, ax3630sSdCardStatus INTEGER, ax3630sSdCardTotalSize INTEGER, ax3630sSdCardUsedSize INTEGER, ax3630sSdCardFreeSize INTEGER, ax3630sPhysLineNumber INTEGER, ax3630sTemperatureStatusNumber INTEGER, ax3630sPowerUnitNumber INTEGER, ax3630sRedundantPsNumber INTEGER, ax3630sFanNumber INTEGER, ax3630sTotalAccumRunTime INTEGER, ax3630sCriticalAccumRunTime INTEGER, ax3630sModuleSlotNumber INTEGER } ax3630sChassisIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to specify ax3630sChassisEntry." ::= { ax3630sChassisEntry 1 } ax3630sChassisType OBJECT-TYPE SYNTAX INTEGER { other(1), model-AX3630S-24T(500), model-AX3630S-24T2X(501), model-AX3630S-24P(502), model-AX3630S-48TR(506), model-AX3630S-48T2XR(507), model-AX3630S-24S2XR(508) } ACCESS read-only STATUS mandatory DESCRIPTION "Chassis type of this system." ::= { ax3630sChassisEntry 2 } ax3630sChassisStatus OBJECT-TYPE SYNTAX INTEGER { up(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of this chassis." ::= { ax3630sChassisEntry 3 } ax3630sStsLedStatus OBJECT-TYPE SYNTAX INTEGER { green-light-blink(1), green-light-on(2), red-light-blink(3), red-light-on(4), light-off(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of STS LED of the device is shown." ::= { ax3630sChassisEntry 4 } ax3630sCpuName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "CPU name is shown by the character string of 16 characters or less." ::= { ax3630sChassisEntry 5 } ax3630sCpuClock OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU clock is shown by the numerical value." ::= { ax3630sChassisEntry 6 } ax3630sMemoryTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The installing memory size is shown by the numerical value. " ::= { ax3630sChassisEntry 7 } ax3630sMemoryUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use memory size is shown by the numerical value." ::= { ax3630sChassisEntry 8 } ax3630sMemoryFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused memory size is shown by the numerical value." ::= { ax3630sChassisEntry 9 } ax3630sRomVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The version of ROM equipped with BCU is shown by the character string." ::= { ax3630sChassisEntry 10 } ax3630sCpuLoad1m OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU utilization of one minute is shown by the numerical value." ::= { ax3630sChassisEntry 11 } ax3630sFlashTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total of filesystem use capacity and unused capacity in a built-in memory is shown." ::= { ax3630sChassisEntry 12 } ax3630sFlashUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the filesystem in a built-in memory is shown." ::= { ax3630sChassisEntry 13 } ax3630sFlashFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused capacity of the filesystem in a built-in memory is shown. " ::= { ax3630sChassisEntry 14 } ax3630sSdCardStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The SD card connection is shown." ::= { ax3630sChassisEntry 15 } ax3630sSdCardTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total capacity of the SD card is shown by the numerical value. It responds by -1 at the MC card unconnection." ::= { ax3630sChassisEntry 16 } ax3630sSdCardUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection. " ::= { ax3630sChassisEntry 17 } ax3630sSdCardFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The remainder capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection." ::= { ax3630sChassisEntry 18 } ax3630sPhysLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of physical lines." ::= { ax3630sChassisEntry 19 } ax3630sTemperatureStatusNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of ax3630sTemperatureStatus in this chassis." ::= { ax3630sChassisEntry 20 } ax3630sPowerUnitNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of maximum power switches that this router can connect its." ::= { ax3630sChassisEntry 21 } ax3630sRedundantPsNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of external power switches that this router can connect its." ::= { ax3630sChassisEntry 22 } ax3630sFanNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of fans that can connect to this chassis." ::= { ax3630sChassisEntry 23 } ax3630sTotalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total operation time after operation of device begins." ::= { ax3630sChassisEntry 24 } ax3630sCriticalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Operating time under environment of 50 degrees C or more." ::= { ax3630sChassisEntry 25 } ax3630sModuleSlotNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of redundant power module that can connect to this chassis." ::= { ax3630sChassisEntry 26 } ax3630sTemperatureStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of ambient temperature status maintained by the environmental monitor." ::= { ax3630sChassis 3 } ax3630sTemperatureStatusEntry OBJECT-TYPE SYNTAX Ax3630sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the ambient temperature status table, representing the status of the associated testpoint maintained by the environmental monitor." INDEX { ax3630sChassisIndex, ax3630sTemperatureStatusIndex } ::= { ax3630sTemperatureStatusTable 1 } Ax3630sTemperatureStatusEntry ::= SEQUENCE { ax3630sTemperatureStatusIndex INTEGER, ax3630sTemperatureStatusDescr DisplayString, ax3630sTemperatureStatusValue Integer32, ax3630sTemperatureThreshold Integer32, ax3630sTemperatureState INTEGER } ax3630sTemperatureStatusIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Unique index for the testpoint being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning." ::= { ax3630sTemperatureStatusEntry 1 } ax3630sTemperatureStatusDescr OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "Textual description of the testpoint being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry." ::= { ax3630sTemperatureStatusEntry 2 } ax3630sTemperatureStatusValue OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The current measurement of the testpoint being instrumented." ::= { ax3630sTemperatureStatusEntry 3 } ax3630sTemperatureThreshold OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The highest value that the associated instance of the object ax3630sTemperatureStatusValue may obtain before an emergency shutdown of the managed device is initiated." ::= { ax3630sTemperatureStatusEntry 4 } ax3630sTemperatureState OBJECT-TYPE SYNTAX INTEGER { normal(1), caution(2), warning(3), fatal(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the testpoint being instrumented." ::= { ax3630sTemperatureStatusEntry 5 } ax3630sPowerUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing power unit information." ::= { ax3630sChassis 4 } ax3630sPowerUnitEntry OBJECT-TYPE SYNTAX Ax3630sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing power unit information." INDEX { ax3630sChassisIndex,ax3630sPowerUnitIndex } ::= { ax3630sPowerUnitTable 1 } Ax3630sPowerUnitTableEntry ::= SEQUENCE { ax3630sPowerUnitIndex INTEGER, ax3630sPowerConnectStatus INTEGER, ax3630sPowerSupplyStatus INTEGER } ax3630sPowerUnitIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the power units.The value from 1 to ax3630sPowerUnitNumber." ::= { ax3630sPowerUnitEntry 1 } ax3630sPowerConnectStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The current connection status of the power unit." ::= { ax3630sPowerUnitEntry 2 } ax3630sPowerSupplyStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), fault(4), disconnected(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of power supply." ::= { ax3630sPowerUnitEntry 3 } ax3630sFanTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing fan information." ::= { ax3630sChassis 5 } ax3630sFanEntry OBJECT-TYPE SYNTAX Ax3630sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry containing information for a fan." INDEX { ax3630sChassisIndex,ax3630sFanIndex } ::= { ax3630sFanTable 1 } Ax3630sFanTableEntry ::= SEQUENCE { ax3630sFanIndex INTEGER, ax3630sFanStatus INTEGER } ax3630sFanIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Index to indicate position of fans." ::= { ax3630sFanEntry 1 } ax3630sFanStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), high-speed(3), fault(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of fans." ::= { ax3630sFanEntry 2 } ax3630sRedundantPsTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sRedundantPsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing external power supply information." ::= { ax3630sChassis 6 } ax3630sRedundantPsEntry OBJECT-TYPE SYNTAX Ax3630sRedundantPsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing external power supply information." INDEX { ax3630sChassisIndex, ax3630sRedundantPsIndex } ::= { ax3630sRedundantPsTable 1 } Ax3630sRedundantPsEntry ::= SEQUENCE { ax3630sRedundantPsIndex INTEGER, ax3630sRedundantPsConnectStatus INTEGER, ax3630sRedundantPsStatus INTEGER } ax3630sRedundantPsIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "An index that shows the external power supply position." ::= { ax3630sRedundantPsEntry 1 } ax3630sRedundantPsConnectStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Mounting an external power supply is shown." ::= { ax3630sRedundantPsEntry 2 } ax3630sRedundantPsStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), fault(4), disconnected(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "The operation of an external power supply is shown." ::= { ax3630sRedundantPsEntry 3 } ax3630sModuleSlotTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing redundunt power module information." ::= { ax3630sChassis 7 } ax3630sModuleSlotEntry OBJECT-TYPE SYNTAX Ax3630sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing redundunt power module information." INDEX { ax3630sChassisIndex, ax3630sModuleSlotIndex } ::= { ax3630sModuleSlotTable 1 } Ax3630sModuleSlotEntry ::= SEQUENCE { ax3630sModuleSlotIndex INTEGER, ax3630sModuleSlotStatus INTEGER, ax3630sModuleSlotType INTEGER } ax3630sModuleSlotIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the module slot units.The value from 1 to ax3630sModuleSlotNumber." ::= { ax3630sModuleSlotEntry 1 } ax3630sModuleSlotStatus OBJECT-TYPE SYNTAX INTEGER{ connected(2), down(4), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Module slot status is shown." ::= { ax3630sModuleSlotEntry 2 } ax3630sModuleSlotType OBJECT-TYPE SYNTAX INTEGER{ powerModule-AC(1), powerModule-DC(2), fanModule(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of module slot is shown." ::= { ax3630sModuleSlotEntry 3 } ax3630sPhysLineTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3630sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing physical port information." ::= { ax3630sPhysLine 1 } ax3630sPhysLineEntry OBJECT-TYPE SYNTAX Ax3630sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing physical port." INDEX { ax3630sChassisIndex, ax3630sPhysLineIndex } ::= { ax3630sPhysLineTable 1 } Ax3630sPhysLineTableEntry ::= SEQUENCE { ax3630sPhysLineIndex INTEGER, ax3630sPhysLineConnectorType INTEGER, ax3630sPhysLineOperStatus INTEGER, ax3630sPhysLineIfIndexNumber INTEGER, ax3630sPhysLineTransceiverStatus INTEGER } ax3630sPhysLineIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Physical port number. The value is from 1 to ax3630sNifLineNumber." ::= { ax3630sPhysLineEntry 1 } ax3630sPhysLineConnectorType OBJECT-TYPE SYNTAX INTEGER { other(1), type1000BASE-LX(301), type1000BASE-SX(302), type1000BASE-LH(303), type1000BASE-BX10-D(304), type1000BASE-BX10-U(305), type1000BASE-BX40-D(306), type1000BASE-BX40-U(307), type1000BASE-SX2(308), type1000BASE-UTP(309), type1000BASE-LHB(310), type10GBASE-SR(401), type10GBASE-LR(402), type10GBASE-ER(403), type10GBASE-ZR(404) } ACCESS read-only STATUS mandatory DESCRIPTION "Connector type is connected physical port. The value is 1(other) when connector is disconnected or connector type is unknown." ::= { ax3630sPhysLineEntry 2 } ax3630sPhysLineOperStatus OBJECT-TYPE SYNTAX INTEGER { other(1), active(2), initialization(3), down(4), lock(6), close(7), line-fault(8), test(9), nothing-configuration(10) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of physical port. The value is -1 when PSU or NIF board is disconnected." ::= { ax3630sPhysLineEntry 3 } ax3630sPhysLineIfIndexNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of ifIndex which is included in physical port.The value is -1 when PSU board or NIF board is disconnected." ::= { ax3630sPhysLineEntry 4 } ax3630sPhysLineTransceiverStatus OBJECT-TYPE SYNTAX INTEGER{ unchangeable-transceiver(1), sfp-mounted(20), sfp-unmounted(21), unsupported-sfp-mounted(22), sfp-status-unknown(23), xfp-mounted(30), xfp-unmounted(31), unsupported-xfp-mounted(32), xfp-status-unknown(33) } ACCESS read-only STATUS mandatory DESCRIPTION "Type and status of replaceable transceiver." ::= { ax3630sPhysLineEntry 5 } -- -- ax3630sFdbClearMIB OBJECT IDENTIFIER ::= { ax3630sOperationCommand 1 } -- ax3630sFdbClearSet OBJECT-TYPE SYNTAX INTEGER { initialValue(0), processing(1), failure(2), success(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Fdb clear information. When want to clear fdb, then set value of this MIB as 1." ::= { ax3630sFdbClearMIB 1 } ax3630sFdbClearReqTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the most recent time that received the demand to clear Fdb information.(sysUpTime)" ::= { ax3630sFdbClearMIB 2 } ax3630sFdbClearSuccessTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the time of the most recent Fdb clearing success.(sysUpTime)" ::= { ax3630sFdbClearMIB 3 } -- ax3640sSwitch group ax3640sModelType OBJECT-TYPE SYNTAX INTEGER { other(1), model-AX3640S-24T(1000), model-AX3640S-24TW(1001), model-AX3640S-24T2XW(1002), model-AX3640S-24SW(1003), model-AX3640S-24S2XW(1004), model-AX3640S-48TW(1005), model-AX3640S-48T2XW(1006) } ACCESS read-only STATUS mandatory DESCRIPTION "Model type of this system." ::= { ax3640sSwitch 1 } --ax3640sSoftware OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "Software information of this system." -- ::= { ax3640sSwitch 2 } ax3640sSoftwareName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Software name of this system." ::= { ax3640sSoftware 1 } ax3640sSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..35)) ACCESS read-only STATUS mandatory DESCRIPTION "System software abbreviation." ::= { ax3640sSoftware 2 } ax3640sSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "System software version." ::= { ax3640sSoftware 3 } --ax3640sSystemMsg OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "System messege group." -- ::= { ax3640sSwitch 3 } ax3640sSystemMsgText OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) ACCESS read-only STATUS mandatory DESCRIPTION "The text of the system log message.For information about this code, see: Operator's Manual. " ::= { ax3640sSystemMsg 1 } ax3640sSystemMsgType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The event type. For information about this code, see: Operator's Manual." ::= { ax3640sSystemMsg 2 } ax3640sSystemMsgTimeStamp OBJECT-TYPE SYNTAX DisplayString (SIZE (0..14)) ACCESS read-only STATUS mandatory DESCRIPTION "The time that event occured. And that is expressed as type of MM/DD hh:mm:ss MM:month(01-12) DD:day(01-31) hh:hour(00-23) mm:minute(00-59) ss:second(00-59) Insert space between DD and hh." ::= { ax3640sSystemMsg 3 } ax3640sSystemMsgLevel OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The newest system message log level.For information about this code, see: Operator's Manual. " ::= { ax3640sSystemMsg 4 } ax3640sSystemMsgEventPoint OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The code of part that system message error occured. For information about this code,see: Operator's Manual. " ::= { ax3640sSystemMsg 5 } ax3640sSystemMsgEventInterfaceID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..40)) ACCESS read-only STATUS mandatory DESCRIPTION "Interface identification of system messages. For information about this code,see: Operator's Manual." ::= { ax3640sSystemMsg 6 } ax3640sSystemMsgEventCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "Event kind code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3640sSystemMsg 7 } ax3640sSystemMsgAdditionalCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "Additional code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3640sSystemMsg 8 } --ax3640sSnmpAgent OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "Related information of SNMP agent." -- ::= { ax3640sSwitch 4 } ax3640sSnmpSendReceiveSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SNMP packet data size in Manager-to-Agent communication. The value is displayed in bytes." ::= { ax3640sSnmpAgent 1 } ax3640sSnmpReceiveDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A recommendable interval to receive packets from Manager.The value is displayed in milliseconds." ::= { ax3640sSnmpAgent 2 } ax3640sSnmpContinuousSend OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of times that is recommendable continuous transmission packets." ::= { ax3640sSnmpAgent 3 } ax3640sSnmpObjectMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of objects that contain SNMP packet." ::= { ax3640sSnmpAgent 4 } --ax3640sSerialNumber OBJECT-TYPE -- SYNTAX DisplayString (SIZE (0..30)) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "Management information (SerialNumber) of RMP2-CARD." -- ::= { ax3640sSwitch 5 } ax3640sLicenseNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of the configured license serial numbers." ::= { ax3640sLicense 1 } ax3640sLicenseTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing the license information." ::= { ax3640sLicense 2 } ax3640sLicenseEntry OBJECT-TYPE SYNTAX Ax3640sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of license information." INDEX { ax3640sLicenseIndex } ::= { ax3640sLicenseTable 1 } Ax3640sLicenseTableEntry ::= SEQUENCE { ax3640sLicenseIndex INTEGER, ax3640sLicenseSerialNumber DisplayString, ax3640sLicenseOptionNumber INTEGER } ax3640sLicenseIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The number is from 1 to ax3640sLicenseNumber." ::= { ax3640sLicenseEntry 1 } ax3640sLicenseSerialNumber OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The serial number." ::= { ax3640sLicenseEntry 2 } ax3640sLicenseOptionNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of option licenses associated with the serial number." ::= { ax3640sLicenseEntry 3 } ax3640sLicenseOptionTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing option licenses information associated with the serial number." ::= { ax3640sLicense 3 } ax3640sLicenseOptionEntry OBJECT-TYPE SYNTAX Ax3640sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of the option license information associated with the serial number." INDEX { ax3640sLicenseOptionIndex,ax3640sLicenseOptionNumberIndex } ::= { ax3640sLicenseOptionTable 1 } Ax3640sLicenseOptionTableEntry ::= SEQUENCE { ax3640sLicenseOptionIndex INTEGER, ax3640sLicenseOptionNumberIndex INTEGER, ax3640sLicenseOptionSoftwareName DisplayString, ax3640sLicenseOptionSoftwareAbbreviation DisplayString } ax3640sLicenseOptionIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The same number as ax3640sLicenseIndex." ::= { ax3640sLicenseOptionEntry 1 } ax3640sLicenseOptionNumberIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number of option licenses information which is given for each serial number. The number is from 1 to ax3640sLicenseNumber." ::= { ax3640sLicenseOptionEntry 2 } ax3640sLicenseOptionSoftwareName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software model name of the option license information associated with the serial number." ::= { ax3640sLicenseOptionEntry 3 } ax3640sLicenseOptionSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software abbreviated name of the option license information associated with the serial number. " ::= { ax3640sLicenseOptionEntry 4 } -- ax3640sDevice group ax3640sChassisMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of cluster chassis that can connect to this router." ::= { ax3640sChassis 1 } ax3640sChassisTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing chassis information." ::= { ax3640sChassis 2 } ax3640sChassisEntry OBJECT-TYPE SYNTAX Ax3640sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing specific chassis." INDEX { ax3640sChassisIndex } ::= { ax3640sChassisTable 1 } Ax3640sChassisTableEntry ::= SEQUENCE { ax3640sChassisIndex INTEGER, ax3640sChassisType INTEGER, ax3640sChassisStatus INTEGER, ax3640sStsLedStatus INTEGER, ax3640sCpuName DisplayString, ax3640sCpuClock INTEGER, ax3640sMemoryTotalSize INTEGER, ax3640sMemoryUsedSize INTEGER, ax3640sMemoryFreeSize INTEGER, ax3640sRomVersion DisplayString, ax3640sCpuLoad1m INTEGER, ax3640sFlashTotalSize INTEGER, ax3640sFlashUsedSize INTEGER, ax3640sFlashFreeSize INTEGER, ax3640sSdCardStatus INTEGER, ax3640sSdCardTotalSize INTEGER, ax3640sSdCardUsedSize INTEGER, ax3640sSdCardFreeSize INTEGER, ax3640sPhysLineNumber INTEGER, ax3640sTemperatureStatusNumber INTEGER, ax3640sPowerUnitNumber INTEGER, ax3640sRedundantPsNumber INTEGER, ax3640sFanNumber INTEGER, ax3640sTotalAccumRunTime INTEGER, ax3640sCriticalAccumRunTime INTEGER, ax3640sModuleSlotNumber INTEGER } ax3640sChassisIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to specify ax3640sChassisEntry." ::= { ax3640sChassisEntry 1 } ax3640sChassisType OBJECT-TYPE SYNTAX INTEGER { other(1), model-AX3640S-24T(1000), model-AX3640S-24TW(1001), model-AX3640S-24T2XW(1002), model-AX3640S-24SW(1003), model-AX3640S-24S2XW(1004), model-AX3640S-48TW(1005), model-AX3640S-48T2XW(1006) } ACCESS read-only STATUS mandatory DESCRIPTION "Chassis type of this system." ::= { ax3640sChassisEntry 2 } ax3640sChassisStatus OBJECT-TYPE SYNTAX INTEGER { up(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of this chassis." ::= { ax3640sChassisEntry 3 } ax3640sStsLedStatus OBJECT-TYPE SYNTAX INTEGER { green-light-blink(1), green-light-on(2), red-light-blink(3), red-light-on(4), light-off(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of STS LED of the device is shown." ::= { ax3640sChassisEntry 4 } ax3640sCpuName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "CPU name is shown by the character string of 16 characters or less." ::= { ax3640sChassisEntry 5 } ax3640sCpuClock OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU clock is shown by the numerical value." ::= { ax3640sChassisEntry 6 } ax3640sMemoryTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The installing memory size is shown by the numerical value. " ::= { ax3640sChassisEntry 7 } ax3640sMemoryUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use memory size is shown by the numerical value." ::= { ax3640sChassisEntry 8 } ax3640sMemoryFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused memory size is shown by the numerical value." ::= { ax3640sChassisEntry 9 } ax3640sRomVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The version of ROM equipped with BCU is shown by the character string." ::= { ax3640sChassisEntry 10 } ax3640sCpuLoad1m OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU utilization of one minute is shown by the numerical value." ::= { ax3640sChassisEntry 11 } ax3640sFlashTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total of filesystem use capacity and unused capacity in a built-in memory is shown." ::= { ax3640sChassisEntry 12 } ax3640sFlashUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the filesystem in a built-in memory is shown." ::= { ax3640sChassisEntry 13 } ax3640sFlashFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused capacity of the filesystem in a built-in memory is shown. " ::= { ax3640sChassisEntry 14 } ax3640sSdCardStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The SD card connection is shown." ::= { ax3640sChassisEntry 15 } ax3640sSdCardTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total capacity of the SD card is shown by the numerical value. It responds by -1 at the MC card unconnection." ::= { ax3640sChassisEntry 16 } ax3640sSdCardUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection. " ::= { ax3640sChassisEntry 17 } ax3640sSdCardFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The remainder capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection." ::= { ax3640sChassisEntry 18 } ax3640sPhysLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of physical lines." ::= { ax3640sChassisEntry 19 } ax3640sTemperatureStatusNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of ax3640sTemperatureStatus in this chassis." ::= { ax3640sChassisEntry 20 } ax3640sPowerUnitNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of maximum power switches that this router can connect its." ::= { ax3640sChassisEntry 21 } ax3640sRedundantPsNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of external power switches that this router can connect its." ::= { ax3640sChassisEntry 22 } ax3640sFanNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of fans that can connect to this chassis." ::= { ax3640sChassisEntry 23 } ax3640sTotalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total operation time after operation of device begins." ::= { ax3640sChassisEntry 24 } ax3640sCriticalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Operating time under environment of 40 degrees C or more." ::= { ax3640sChassisEntry 25 } ax3640sModuleSlotNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of redundant power module that can connect to this chassis." ::= { ax3640sChassisEntry 26 } ax3640sTemperatureStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of ambient temperature status maintained by the environmental monitor." ::= { ax3640sChassis 3 } ax3640sTemperatureStatusEntry OBJECT-TYPE SYNTAX Ax3640sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the ambient temperature status table, representing the status of the associated testpoint maintained by the environmental monitor." INDEX { ax3640sChassisIndex, ax3640sTemperatureStatusIndex } ::= { ax3640sTemperatureStatusTable 1 } Ax3640sTemperatureStatusEntry ::= SEQUENCE { ax3640sTemperatureStatusIndex INTEGER, ax3640sTemperatureStatusDescr DisplayString, ax3640sTemperatureStatusValue Integer32, ax3640sTemperatureThreshold Integer32, ax3640sTemperatureState INTEGER } ax3640sTemperatureStatusIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Unique index for the testpoint being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning." ::= { ax3640sTemperatureStatusEntry 1 } ax3640sTemperatureStatusDescr OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "Textual description of the testpoint being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry." ::= { ax3640sTemperatureStatusEntry 2 } ax3640sTemperatureStatusValue OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The current measurement of the testpoint being instrumented." ::= { ax3640sTemperatureStatusEntry 3 } ax3640sTemperatureThreshold OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The highest value that the associated instance of the object ax3640sTemperatureStatusValue may obtain before an emergency shutdown of the managed device is initiated." ::= { ax3640sTemperatureStatusEntry 4 } ax3640sTemperatureState OBJECT-TYPE SYNTAX INTEGER { normal(1), caution(2), warning(3), fatal(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the testpoint being instrumented." ::= { ax3640sTemperatureStatusEntry 5 } ax3640sPowerUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing power unit information." ::= { ax3640sChassis 4 } ax3640sPowerUnitEntry OBJECT-TYPE SYNTAX Ax3640sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing power unit information." INDEX { ax3640sChassisIndex,ax3640sPowerUnitIndex } ::= { ax3640sPowerUnitTable 1 } Ax3640sPowerUnitTableEntry ::= SEQUENCE { ax3640sPowerUnitIndex INTEGER, ax3640sPowerConnectStatus INTEGER, ax3640sPowerSupplyStatus INTEGER } ax3640sPowerUnitIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the power units.The value from 1 to ax3640sPowerUnitNumber." ::= { ax3640sPowerUnitEntry 1 } ax3640sPowerConnectStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The current connection status of the power unit." ::= { ax3640sPowerUnitEntry 2 } ax3640sPowerSupplyStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), fault(4), disconnected(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of power supply." ::= { ax3640sPowerUnitEntry 3 } ax3640sFanTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing fan information." ::= { ax3640sChassis 5 } ax3640sFanEntry OBJECT-TYPE SYNTAX Ax3640sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry containing information for a fan." INDEX { ax3640sChassisIndex,ax3640sFanIndex } ::= { ax3640sFanTable 1 } Ax3640sFanTableEntry ::= SEQUENCE { ax3640sFanIndex INTEGER, ax3640sFanStatus INTEGER } ax3640sFanIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Index to indicate position of fans." ::= { ax3640sFanEntry 1 } ax3640sFanStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), high-speed(3), fault(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of fans." ::= { ax3640sFanEntry 2 } ax3640sRedundantPsTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sRedundantPsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing external power supply information." ::= { ax3640sChassis 6 } ax3640sRedundantPsEntry OBJECT-TYPE SYNTAX Ax3640sRedundantPsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing external power supply information." INDEX { ax3640sChassisIndex, ax3640sRedundantPsIndex } ::= { ax3640sRedundantPsTable 1 } Ax3640sRedundantPsEntry ::= SEQUENCE { ax3640sRedundantPsIndex INTEGER, ax3640sRedundantPsConnectStatus INTEGER, ax3640sRedundantPsStatus INTEGER } ax3640sRedundantPsIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "An index that shows the external power supply position." ::= { ax3640sRedundantPsEntry 1 } ax3640sRedundantPsConnectStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Mounting an external power supply is shown." ::= { ax3640sRedundantPsEntry 2 } ax3640sRedundantPsStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), fault(4), disconnected(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "The operation of an external power supply is shown." ::= { ax3640sRedundantPsEntry 3 } ax3640sModuleSlotTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing redundunt power module information." ::= { ax3640sChassis 7 } ax3640sModuleSlotEntry OBJECT-TYPE SYNTAX Ax3640sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing redundunt power module information." INDEX { ax3640sChassisIndex, ax3640sModuleSlotIndex } ::= { ax3640sModuleSlotTable 1 } Ax3640sModuleSlotEntry ::= SEQUENCE { ax3640sModuleSlotIndex INTEGER, ax3640sModuleSlotStatus INTEGER, ax3640sModuleSlotType INTEGER } ax3640sModuleSlotIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the module slot units.The value from 1 to ax3640sModuleSlotNumber." ::= { ax3640sModuleSlotEntry 1 } ax3640sModuleSlotStatus OBJECT-TYPE SYNTAX INTEGER{ connected(2), down(4), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Module slot status is shown." ::= { ax3640sModuleSlotEntry 2 } ax3640sModuleSlotType OBJECT-TYPE SYNTAX INTEGER{ powerModule-AC(1), powerModule-DC(2), fanModule(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of module slot is shown." ::= { ax3640sModuleSlotEntry 3 } ax3640sPhysLineTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3640sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing physical port information." ::= { ax3640sPhysLine 1 } ax3640sPhysLineEntry OBJECT-TYPE SYNTAX Ax3640sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing physical port." INDEX { ax3640sChassisIndex, ax3640sPhysLineIndex } ::= { ax3640sPhysLineTable 1 } Ax3640sPhysLineTableEntry ::= SEQUENCE { ax3640sPhysLineIndex INTEGER, ax3640sPhysLineConnectorType INTEGER, ax3640sPhysLineOperStatus INTEGER, ax3640sPhysLineIfIndexNumber INTEGER, ax3640sPhysLineTransceiverStatus INTEGER } ax3640sPhysLineIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Physical port number. The value is from 1 to ax3640sNifLineNumber." ::= { ax3640sPhysLineEntry 1 } ax3640sPhysLineConnectorType OBJECT-TYPE SYNTAX INTEGER { other(1), type100BASE-FX(201), type1000BASE-LX(301), type1000BASE-SX(302), type1000BASE-LH(303), type1000BASE-BX10-D(304), type1000BASE-BX10-U(305), type1000BASE-BX40-D(306), type1000BASE-BX40-U(307), type1000BASE-SX2(308), type1000BASE-UTP(309), type1000BASE-LHB(310), type10GBASE-SR(401), type10GBASE-LR(402), type10GBASE-ER(403), type10GBASE-ZR(404) } ACCESS read-only STATUS mandatory DESCRIPTION "Connector type is connected physical port. The value is 1(other) when connector is disconnected or connector type is unknown." ::= { ax3640sPhysLineEntry 2 } ax3640sPhysLineOperStatus OBJECT-TYPE SYNTAX INTEGER { other(1), active(2), initialization(3), down(4), lock(6), close(7), line-fault(8), test(9), nothing-configuration(10) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of physical port. The value is -1 when PSU or NIF board is disconnected." ::= { ax3640sPhysLineEntry 3 } ax3640sPhysLineIfIndexNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of ifIndex which is included in physical port.The value is -1 when PSU board or NIF board is disconnected." ::= { ax3640sPhysLineEntry 4 } ax3640sPhysLineTransceiverStatus OBJECT-TYPE SYNTAX INTEGER{ unchangeable-transceiver(1), sfp-mounted(20), sfp-unmounted(21), unsupported-sfp-mounted(22), sfp-status-unknown(23), xfp-mounted(30), xfp-unmounted(31), unsupported-xfp-mounted(32), xfp-status-unknown(33) } ACCESS read-only STATUS mandatory DESCRIPTION "Type and status of replaceable transceiver." ::= { ax3640sPhysLineEntry 5 } -- -- ax3640sFdbClearMIB OBJECT IDENTIFIER ::= { ax3640sOperationCommand 1 } -- ax3640sFdbClearSet OBJECT-TYPE SYNTAX INTEGER { initialValue(0), processing(1), failure(2), success(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Fdb clear information. When want to clear fdb, then set value of this MIB as 1." ::= { ax3640sFdbClearMIB 1 } ax3640sFdbClearReqTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the most recent time that received the demand to clear Fdb information.(sysUpTime)" ::= { ax3640sFdbClearMIB 2 } ax3640sFdbClearSuccessTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the time of the most recent Fdb clearing success.(sysUpTime)" ::= { ax3640sFdbClearMIB 3 } -- ax3650sSwitch group ax3650sModelType OBJECT-TYPE SYNTAX INTEGER { other(1), model-AX3650S-24T6XW(1150), model-AX3650S-20S6XW(1151), model-AX3650S-48T4XW(1152) } ACCESS read-only STATUS mandatory DESCRIPTION "Model type of this system." ::= { ax3650sSwitch 1 } --ax3650sSoftware OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "Software information of this system." -- ::= { ax3650sSwitch 2 } ax3650sSoftwareName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Software name of this system." ::= { ax3650sSoftware 1 } ax3650sSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..36)) ACCESS read-only STATUS mandatory DESCRIPTION "System software abbreviation." ::= { ax3650sSoftware 2 } ax3650sSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "System software version." ::= { ax3650sSoftware 3 } --ax3650sSystemMsg OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "System messege group." -- ::= { ax3650sSwitch 3 } ax3650sSystemMsgText OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) ACCESS read-only STATUS mandatory DESCRIPTION "The text of the system log message.For information about this code, see: Operator's Manual. " ::= { ax3650sSystemMsg 1 } ax3650sSystemMsgType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The event type. For information about this code, see: Operator's Manual." ::= { ax3650sSystemMsg 2 } ax3650sSystemMsgTimeStamp OBJECT-TYPE SYNTAX DisplayString (SIZE (0..14)) ACCESS read-only STATUS mandatory DESCRIPTION "The time that event occured. And that is expressed as type of MM/DD hh:mm:ss MM:month(01-12) DD:day(01-31) hh:hour(00-23) mm:minute(00-59) ss:second(00-59) Insert space between DD and hh." ::= { ax3650sSystemMsg 3 } ax3650sSystemMsgLevel OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The newest system message log level.For information about this code, see: Operator's Manual. " ::= { ax3650sSystemMsg 4 } ax3650sSystemMsgEventPoint OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The code of part that system message error occured. For information about this code,see: Operator's Manual. " ::= { ax3650sSystemMsg 5 } ax3650sSystemMsgEventInterfaceID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..40)) ACCESS read-only STATUS mandatory DESCRIPTION "Interface identification of system messages. For information about this code,see: Operator's Manual." ::= { ax3650sSystemMsg 6 } ax3650sSystemMsgEventCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "Event kind code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3650sSystemMsg 7 } ax3650sSystemMsgAdditionalCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "Additional code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3650sSystemMsg 8 } --ax3650sSnmpAgent OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS not-accessible -- STATUS mandatory -- DESCRIPTION -- "Related information of SNMP agent." -- ::= { ax3650sSwitch 4 } ax3650sSnmpSendReceiveSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SNMP packet data size in Manager-to-Agent communication. The value is displayed in bytes." ::= { ax3650sSnmpAgent 1 } ax3650sSnmpReceiveDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A recommendable interval to receive packets from Manager.The value is displayed in milliseconds." ::= { ax3650sSnmpAgent 2 } ax3650sSnmpContinuousSend OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of times that is recommendable continuous transmission packets." ::= { ax3650sSnmpAgent 3 } ax3650sSnmpObjectMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of objects that contain SNMP packet." ::= { ax3650sSnmpAgent 4 } --ax3650sSerialNumber OBJECT-TYPE -- SYNTAX DisplayString (SIZE (0..30)) -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "Management information (SerialNumber) of RMP2-CARD." -- ::= { ax3650sSwitch 5 } ax3650sLicenseNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of the configured license serial numbers." ::= { ax3650sLicense 1 } ax3650sLicenseTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing the license information." ::= { ax3650sLicense 2 } ax3650sLicenseEntry OBJECT-TYPE SYNTAX Ax3650sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of license information." INDEX { ax3650sLicenseIndex } ::= { ax3650sLicenseTable 1 } Ax3650sLicenseTableEntry ::= SEQUENCE { ax3650sLicenseIndex INTEGER, ax3650sLicenseSerialNumber DisplayString, ax3650sLicenseOptionNumber INTEGER } ax3650sLicenseIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The number is from 1 to ax3650sLicenseNumber." ::= { ax3650sLicenseEntry 1 } ax3650sLicenseSerialNumber OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The serial number." ::= { ax3650sLicenseEntry 2 } ax3650sLicenseOptionNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of option licenses associated with the serial number." ::= { ax3650sLicenseEntry 3 } ax3650sLicenseOptionTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing option licenses information associated with the serial number." ::= { ax3650sLicense 3 } ax3650sLicenseOptionEntry OBJECT-TYPE SYNTAX Ax3650sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of the option license information associated with the serial number." INDEX { ax3650sLicenseOptionIndex,ax3650sLicenseOptionNumberIndex } ::= { ax3650sLicenseOptionTable 1 } Ax3650sLicenseOptionTableEntry ::= SEQUENCE { ax3650sLicenseOptionIndex INTEGER, ax3650sLicenseOptionNumberIndex INTEGER, ax3650sLicenseOptionSoftwareName DisplayString, ax3650sLicenseOptionSoftwareAbbreviation DisplayString } ax3650sLicenseOptionIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The same number as ax3650sLicenseIndex." ::= { ax3650sLicenseOptionEntry 1 } ax3650sLicenseOptionNumberIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number of option licenses information which is given for each serial number. The number is from 1 to ax3650sLicenseNumber." ::= { ax3650sLicenseOptionEntry 2 } ax3650sLicenseOptionSoftwareName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software model name of the option license information associated with the serial number." ::= { ax3650sLicenseOptionEntry 3 } ax3650sLicenseOptionSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software abbreviated name of the option license information associated with the serial number. " ::= { ax3650sLicenseOptionEntry 4 } -- ax3650sDevice group ax3650sChassisMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of cluster chassis that can connect to this router." ::= { ax3650sChassis 1 } ax3650sChassisTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing chassis information." ::= { ax3650sChassis 2 } ax3650sChassisEntry OBJECT-TYPE SYNTAX Ax3650sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing specific chassis." INDEX { ax3650sChassisIndex } ::= { ax3650sChassisTable 1 } Ax3650sChassisTableEntry ::= SEQUENCE { ax3650sChassisIndex INTEGER, ax3650sChassisType INTEGER, ax3650sChassisStatus INTEGER, ax3650sStsLedStatus INTEGER, ax3650sCpuName DisplayString, ax3650sCpuClock INTEGER, ax3650sMemoryTotalSize INTEGER, ax3650sMemoryUsedSize INTEGER, ax3650sMemoryFreeSize INTEGER, ax3650sRomVersion DisplayString, ax3650sCpuLoad1m INTEGER, ax3650sFlashTotalSize INTEGER, ax3650sFlashUsedSize INTEGER, ax3650sFlashFreeSize INTEGER, ax3650sSdCardStatus INTEGER, ax3650sSdCardTotalSize INTEGER, ax3650sSdCardUsedSize INTEGER, ax3650sSdCardFreeSize INTEGER, ax3650sPhysLineNumber INTEGER, ax3650sTemperatureStatusNumber INTEGER, ax3650sPowerUnitNumber INTEGER, ax3650sRedundantPsNumber INTEGER, ax3650sFanNumber INTEGER, ax3650sTotalAccumRunTime INTEGER, ax3650sCriticalAccumRunTime INTEGER, ax3650sModuleSlotNumber INTEGER } ax3650sChassisIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to specify ax3650sChassisEntry." ::= { ax3650sChassisEntry 1 } ax3650sChassisType OBJECT-TYPE SYNTAX INTEGER { other(1), model-AX3650S-24T6XW(1150), model-AX3650S-20S6XW(1151), model-AX3650S-48T4XW(1152) } ACCESS read-only STATUS mandatory DESCRIPTION "Chassis type of this system." ::= { ax3650sChassisEntry 2 } ax3650sChassisStatus OBJECT-TYPE SYNTAX INTEGER { up(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of this chassis." ::= { ax3650sChassisEntry 3 } ax3650sStsLedStatus OBJECT-TYPE SYNTAX INTEGER { green-light-blink(1), green-light-on(2), red-light-blink(3), red-light-on(4), light-off(6), green-light-blink2(7) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of STS LED of the device is shown." ::= { ax3650sChassisEntry 4 } ax3650sCpuName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "CPU name is shown by the character string of 16 characters or less." ::= { ax3650sChassisEntry 5 } ax3650sCpuClock OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU clock is shown by the numerical value." ::= { ax3650sChassisEntry 6 } ax3650sMemoryTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The installing memory size is shown by the numerical value. " ::= { ax3650sChassisEntry 7 } ax3650sMemoryUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use memory size is shown by the numerical value." ::= { ax3650sChassisEntry 8 } ax3650sMemoryFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused memory size is shown by the numerical value." ::= { ax3650sChassisEntry 9 } ax3650sRomVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The version of ROM equipped with BCU is shown by the character string." ::= { ax3650sChassisEntry 10 } ax3650sCpuLoad1m OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU utilization of one minute is shown by the numerical value." ::= { ax3650sChassisEntry 11 } ax3650sFlashTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total of filesystem use capacity and unused capacity in a built-in memory is shown." ::= { ax3650sChassisEntry 12 } ax3650sFlashUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the filesystem in a built-in memory is shown." ::= { ax3650sChassisEntry 13 } ax3650sFlashFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused capacity of the filesystem in a built-in memory is shown. " ::= { ax3650sChassisEntry 14 } ax3650sSdCardStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The SD card connection is shown." ::= { ax3650sChassisEntry 15 } ax3650sSdCardTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total capacity of the SD card is shown by the numerical value. It responds by -1 at the MC card unconnection." ::= { ax3650sChassisEntry 16 } ax3650sSdCardUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection. " ::= { ax3650sChassisEntry 17 } ax3650sSdCardFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The remainder capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection." ::= { ax3650sChassisEntry 18 } ax3650sPhysLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of physical lines." ::= { ax3650sChassisEntry 19 } ax3650sTemperatureStatusNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of ax3650sTemperatureStatus in this chassis." ::= { ax3650sChassisEntry 20 } ax3650sPowerUnitNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of maximum power switches that this router can connect its." ::= { ax3650sChassisEntry 21 } ax3650sRedundantPsNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of external power switches that this router can connect its." ::= { ax3650sChassisEntry 22 } ax3650sFanNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of fans that can connect to this chassis." ::= { ax3650sChassisEntry 23 } ax3650sTotalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total operation time after operation of device begins." ::= { ax3650sChassisEntry 24 } ax3650sCriticalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Operating time under environment of 50 degrees C or more." ::= { ax3650sChassisEntry 25 } ax3650sModuleSlotNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of redundant power module that can connect to this chassis." ::= { ax3650sChassisEntry 26 } ax3650sTemperatureStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of ambient temperature status maintained by the environmental monitor." ::= { ax3650sChassis 3 } ax3650sTemperatureStatusEntry OBJECT-TYPE SYNTAX Ax3650sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the ambient temperature status table, representing the status of the associated testpoint maintained by the environmental monitor." INDEX { ax3650sChassisIndex, ax3650sTemperatureStatusIndex } ::= { ax3650sTemperatureStatusTable 1 } Ax3650sTemperatureStatusEntry ::= SEQUENCE { ax3650sTemperatureStatusIndex INTEGER, ax3650sTemperatureStatusDescr DisplayString, ax3650sTemperatureStatusValue Integer32, ax3650sTemperatureThreshold Integer32, ax3650sTemperatureState INTEGER } ax3650sTemperatureStatusIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Unique index for the testpoint being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning." ::= { ax3650sTemperatureStatusEntry 1 } ax3650sTemperatureStatusDescr OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "Textual description of the testpoint being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry." ::= { ax3650sTemperatureStatusEntry 2 } ax3650sTemperatureStatusValue OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The current measurement of the testpoint being instrumented." ::= { ax3650sTemperatureStatusEntry 3 } ax3650sTemperatureThreshold OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The highest value that the associated instance of the object ax3650sTemperatureStatusValue may obtain before an emergency shutdown of the managed device is initiated." ::= { ax3650sTemperatureStatusEntry 4 } ax3650sTemperatureState OBJECT-TYPE SYNTAX INTEGER { normal(1), caution(2), warning(3), fatal(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the testpoint being instrumented." ::= { ax3650sTemperatureStatusEntry 5 } ax3650sPowerUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing power unit information." ::= { ax3650sChassis 4 } ax3650sPowerUnitEntry OBJECT-TYPE SYNTAX Ax3650sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing power unit information." INDEX { ax3650sChassisIndex,ax3650sPowerUnitIndex } ::= { ax3650sPowerUnitTable 1 } Ax3650sPowerUnitTableEntry ::= SEQUENCE { ax3650sPowerUnitIndex INTEGER, ax3650sPowerConnectStatus INTEGER, ax3650sPowerSupplyStatus INTEGER, ax3650sPowerSlotType INTEGER } ax3650sPowerUnitIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the power units.The value from 1 to ax3650sPowerUnitNumber." ::= { ax3650sPowerUnitEntry 1 } ax3650sPowerConnectStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The current connection status of the power unit." ::= { ax3650sPowerUnitEntry 2 } ax3650sPowerSupplyStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), fault(4), disconnected(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of power supply." ::= { ax3650sPowerUnitEntry 3 } ax3650sPowerSlotType OBJECT-TYPE SYNTAX INTEGER { powerModule-AC(1), powerModule-DC(2), unknown(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of power slot is shown." ::= { ax3650sPowerUnitEntry 4 } ax3650sFanTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing fan information." ::= { ax3650sChassis 5 } ax3650sFanEntry OBJECT-TYPE SYNTAX Ax3650sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry containing information for a fan." INDEX { ax3650sChassisIndex,ax3650sFanIndex } ::= { ax3650sFanTable 1 } Ax3650sFanTableEntry ::= SEQUENCE { ax3650sFanIndex INTEGER, ax3650sFanStatus INTEGER } ax3650sFanIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Index to indicate position of fans." ::= { ax3650sFanEntry 1 } ax3650sFanStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), high-speed(3), fault(4), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of fans." ::= { ax3650sFanEntry 2 } ax3650sModuleSlotTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing redundunt power module information." ::= { ax3650sChassis 7 } ax3650sModuleSlotEntry OBJECT-TYPE SYNTAX Ax3650sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing redundunt power module information." INDEX { ax3650sChassisIndex, ax3650sModuleSlotIndex } ::= { ax3650sModuleSlotTable 1 } Ax3650sModuleSlotEntry ::= SEQUENCE { ax3650sModuleSlotIndex INTEGER, ax3650sModuleSlotStatus INTEGER, ax3650sModuleSlotType INTEGER } ax3650sModuleSlotIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the module slot units.The value from 1 to ax3650sModuleSlotNumber." ::= { ax3650sModuleSlotEntry 1 } ax3650sModuleSlotStatus OBJECT-TYPE SYNTAX INTEGER{ connected(2), down(4), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Module slot status is shown." ::= { ax3650sModuleSlotEntry 2 } ax3650sModuleSlotType OBJECT-TYPE SYNTAX INTEGER{ powerModule-AC(1), powerModule-DC(2), unknown(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of module slot is shown." ::= { ax3650sModuleSlotEntry 3 } ax3650sPhysLineTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3650sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing physical port information." ::= { ax3650sPhysLine 1 } ax3650sPhysLineEntry OBJECT-TYPE SYNTAX Ax3650sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing physical port." INDEX { ax3650sChassisIndex, ax3650sPhysLineIndex } ::= { ax3650sPhysLineTable 1 } Ax3650sPhysLineTableEntry ::= SEQUENCE { ax3650sPhysLineIndex INTEGER, ax3650sPhysLineConnectorType INTEGER, ax3650sPhysLineOperStatus INTEGER, ax3650sPhysLineIfIndexNumber INTEGER, ax3650sPhysLineTransceiverStatus INTEGER } ax3650sPhysLineIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Physical port number. The value is from 1 to ax3650sNifLineNumber." ::= { ax3650sPhysLineEntry 1 } ax3650sPhysLineConnectorType OBJECT-TYPE SYNTAX INTEGER { other(1), type100BASE-FX(201), type1000BASE-LX(301), type1000BASE-SX(302), type1000BASE-LH(303), type1000BASE-BX10-D(304), type1000BASE-BX10-U(305), type1000BASE-BX40-D(306), type1000BASE-BX40-U(307), type1000BASE-SX2(308), type1000BASE-UTP(309), type1000BASE-LHB(310), type10GBASE-SR(401), type10GBASE-LR(402), type10GBASE-ER(403), type10GBASE-ZR(404), type10GBASE-CU1M(405), type10GBASE-CU3M(406), type10GBASE-CU5M(407), type10GBASE-CU30CM(408), type10GBASE-BR10-D(409), type10GBASE-BR10-U(410), type10GBASE-BR40-D(411), type10GBASE-BR40-U(412) } ACCESS read-only STATUS mandatory DESCRIPTION "Connector type is connected physical port. The value is 1(other) when connector is disconnected or connector type is unknown." ::= { ax3650sPhysLineEntry 2 } ax3650sPhysLineOperStatus OBJECT-TYPE SYNTAX INTEGER { other(1), active(2), initialization(3), down(4), lock(6), close(7), line-fault(8), test(9), nothing-configuration(10) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of physical port. The value is -1 when PSU or NIF board is disconnected." ::= { ax3650sPhysLineEntry 3 } ax3650sPhysLineIfIndexNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of ifIndex which is included in physical port.The value is -1 when PSU board or NIF board is disconnected." ::= { ax3650sPhysLineEntry 4 } ax3650sPhysLineTransceiverStatus OBJECT-TYPE SYNTAX INTEGER{ unchangeable-transceiver(1), sfp-mounted(20), sfp-unmounted(21), unsupported-sfp-mounted(22), sfp-status-unknown(23) } ACCESS read-only STATUS mandatory DESCRIPTION "Type and status of replaceable transceiver." ::= { ax3650sPhysLineEntry 5 } -- -- ax3650sFdbClearMIB OBJECT IDENTIFIER ::= { ax3650sOperationCommand 1 } -- ax3650sFdbClearSet OBJECT-TYPE SYNTAX INTEGER { initialValue(0), processing(1), failure(2), success(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Fdb clear information. When want to clear fdb, then set value of this MIB as 1." ::= { ax3650sFdbClearMIB 1 } ax3650sFdbClearReqTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the most recent time that received the demand to clear Fdb information.(sysUpTime)" ::= { ax3650sFdbClearMIB 2 } ax3650sFdbClearSuccessTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the time of the most recent Fdb clearing success.(sysUpTime)" ::= { ax3650sFdbClearMIB 3 } -- ax3830sSwitch group ax3830sModelType OBJECT-TYPE SYNTAX INTEGER { model-AX3830S-44XW(1700), model-AX3830S-44X4QW(1701), model-AX3830S-44X4QS(1702), model-AX3830S-32X4QW(1703) } ACCESS read-only STATUS mandatory DESCRIPTION "Model type of this system." ::= { ax3830sSwitch 1 } ax3830sSoftwareName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "Software name of this system." ::= { ax3830sSoftware 1 } ax3830sSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..36)) ACCESS read-only STATUS mandatory DESCRIPTION "System software abbreviation." ::= { ax3830sSoftware 2 } ax3830sSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "System software version." ::= { ax3830sSoftware 3 } ax3830sSystemMsgText OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) ACCESS read-only STATUS mandatory DESCRIPTION "The text of the system log message.For information about this code, see: Operator's Manual. " ::= { ax3830sSystemMsg 1 } ax3830sSystemMsgType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The event type. For information about this code, see: Operator's Manual." ::= { ax3830sSystemMsg 2 } ax3830sSystemMsgTimeStamp OBJECT-TYPE SYNTAX DisplayString (SIZE (0..14)) ACCESS read-only STATUS mandatory DESCRIPTION "The time that event occured. And that is expressed as type of MM/DD hh:mm:ss MM:month(01-12) DD:day(01-31) hh:hour(00-23) mm:minute(00-59) ss:second(00-59) Insert space between DD and hh." ::= { ax3830sSystemMsg 3 } ax3830sSystemMsgLevel OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) ACCESS read-only STATUS mandatory DESCRIPTION "The newest system message log level.For information about this code, see: Operator's Manual. " ::= { ax3830sSystemMsg 4 } ax3830sSystemMsgEventPoint OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) ACCESS read-only STATUS mandatory DESCRIPTION "The code of part that system message error occured. For information about this code,see: Operator's Manual. " ::= { ax3830sSystemMsg 5 } ax3830sSystemMsgEventInterfaceID OBJECT-TYPE SYNTAX DisplayString (SIZE (0..40)) ACCESS read-only STATUS mandatory DESCRIPTION "Interface identification of system messages. For information about this code,see: Operator's Manual." ::= { ax3830sSystemMsg 6 } ax3830sSystemMsgEventCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "Event kind code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3830sSystemMsg 7 } ax3830sSystemMsgAdditionalCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "Additional code of system messages. For information about this code, see: Operator's Manual. " ::= { ax3830sSystemMsg 8 } ax3830sSnmpSendReceiveSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "SNMP packet data size in Manager-to-Agent communication. The value is displayed in bytes." ::= { ax3830sSnmpAgent 1 } ax3830sSnmpReceiveDelay OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A recommendable interval to receive packets from Manager.The value is displayed in milliseconds." ::= { ax3830sSnmpAgent 2 } ax3830sSnmpContinuousSend OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of times that is recommendable continuous transmission packets." ::= { ax3830sSnmpAgent 3 } ax3830sSnmpObjectMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of objects that contain SNMP packet." ::= { ax3830sSnmpAgent 4 } ax3830sLicenseNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of the configured license serial numbers." ::= { ax3830sLicense 1 } ax3830sLicenseTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing the license information." ::= { ax3830sLicense 2 } ax3830sLicenseEntry OBJECT-TYPE SYNTAX Ax3830sLicenseTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of license information." INDEX { ax3830sLicenseIndex } ::= { ax3830sLicenseTable 1 } Ax3830sLicenseTableEntry ::= SEQUENCE { ax3830sLicenseIndex INTEGER, ax3830sLicenseSerialNumber DisplayString, ax3830sLicenseOptionNumber INTEGER } ax3830sLicenseIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The number is from 1 to ax3830sLicenseNumber." ::= { ax3830sLicenseEntry 1 } ax3830sLicenseSerialNumber OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The serial number." ::= { ax3830sLicenseEntry 2 } ax3830sLicenseOptionNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of option licenses associated with the serial number." ::= { ax3830sLicenseEntry 3 } ax3830sLicenseOptionTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing option licenses information associated with the serial number." ::= { ax3830sLicense 3 } ax3830sLicenseOptionEntry OBJECT-TYPE SYNTAX Ax3830sLicenseOptionTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The entry of the option license information associated with the serial number." INDEX { ax3830sLicenseOptionIndex, ax3830sLicenseOptionNumberIndex } ::= { ax3830sLicenseOptionTable 1 } Ax3830sLicenseOptionTableEntry ::= SEQUENCE { ax3830sLicenseOptionIndex INTEGER, ax3830sLicenseOptionNumberIndex INTEGER, ax3830sLicenseOptionSoftwareName DisplayString, ax3830sLicenseOptionSoftwareAbbreviation DisplayString } ax3830sLicenseOptionIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number given for each serial number. The same number as ax3830sLicenseIndex." ::= { ax3830sLicenseOptionEntry 1 } ax3830sLicenseOptionNumberIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "The unique index number of option licenses information which is given for each serial number. The number is from 1 to ax3830sLicenseNumber." ::= { ax3830sLicenseOptionEntry 2 } ax3830sLicenseOptionSoftwareName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software model name of the option license information associated with the serial number." ::= { ax3830sLicenseOptionEntry 3 } ax3830sLicenseOptionSoftwareAbbreviation OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The software abbreviated name of the option license information associated with the serial number. " ::= { ax3830sLicenseOptionEntry 4 } -- ax3830sDevice group ax3830sChassisMaxNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Max number of cluster chassis that can connect to this router." ::= { ax3830sChassis 1 } ax3830sChassisTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing chassis information." ::= { ax3830sChassis 2 } ax3830sChassisEntry OBJECT-TYPE SYNTAX Ax3830sChassisTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing specific chassis." INDEX { ax3830sChassisIndex } ::= { ax3830sChassisTable 1 } Ax3830sChassisTableEntry ::= SEQUENCE { ax3830sChassisIndex INTEGER, ax3830sChassisType INTEGER, ax3830sChassisStatus INTEGER, ax3830sStsLedStatus INTEGER, ax3830sCpuName DisplayString, ax3830sCpuClock INTEGER, ax3830sMemoryTotalSize INTEGER, ax3830sMemoryUsedSize INTEGER, ax3830sMemoryFreeSize INTEGER, ax3830sRomVersion DisplayString, ax3830sCpuLoad1m INTEGER, ax3830sFlashTotalSize INTEGER, ax3830sFlashUsedSize INTEGER, ax3830sFlashFreeSize INTEGER, ax3830sSdCardStatus INTEGER, ax3830sSdCardTotalSize INTEGER, ax3830sSdCardUsedSize INTEGER, ax3830sSdCardFreeSize INTEGER, ax3830sPhysLineNumber INTEGER, ax3830sTemperatureStatusNumber INTEGER, ax3830sPowerUnitNumber INTEGER, ax3830sRedundantPsNumber INTEGER, ax3830sFanNumber INTEGER, ax3830sTotalAccumRunTime INTEGER, ax3830sCriticalAccumRunTime INTEGER, ax3830sModuleSlotNumber INTEGER, ax3830sMgmtPortStatus INTEGER } ax3830sChassisIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to specify ax3830sChassisEntry." ::= { ax3830sChassisEntry 1 } ax3830sChassisType OBJECT-TYPE SYNTAX INTEGER { model-AX3830S-44XW(1700), model-AX3830S-44X4QW(1701), model-AX3830S-44X4QS(1702), model-AX3830S-32X4QW(1703) } ACCESS read-only STATUS mandatory DESCRIPTION "Chassis type of this system." ::= { ax3830sChassisEntry 2 } ax3830sChassisStatus OBJECT-TYPE SYNTAX INTEGER { up(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current status of this chassis." ::= { ax3830sChassisEntry 3 } ax3830sStsLedStatus OBJECT-TYPE SYNTAX INTEGER { green-light-blink(1), green-light-on(2), red-light-blink(3), red-light-on(4), light-off(6), green-light-blink2(7) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of STS LED of the device is shown." ::= { ax3830sChassisEntry 4 } ax3830sCpuName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "CPU name is shown by the character string of 16 characters or less." ::= { ax3830sChassisEntry 5 } ax3830sCpuClock OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU clock is shown by the numerical value." ::= { ax3830sChassisEntry 6 } ax3830sMemoryTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The installing memory size is shown by the numerical value. " ::= { ax3830sChassisEntry 7 } ax3830sMemoryUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use memory size is shown by the numerical value." ::= { ax3830sChassisEntry 8 } ax3830sMemoryFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused memory size is shown by the numerical value." ::= { ax3830sChassisEntry 9 } ax3830sRomVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The version of ROM equipped with BCU is shown by the character string." ::= { ax3830sChassisEntry 10 } ax3830sCpuLoad1m OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "CPU utilization of one minute is shown by the numerical value." ::= { ax3830sChassisEntry 11 } ax3830sFlashTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total of filesystem use capacity and unused capacity in a built-in memory is shown." ::= { ax3830sChassisEntry 12 } ax3830sFlashUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the filesystem in a built-in memory is shown." ::= { ax3830sChassisEntry 13 } ax3830sFlashFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The unused capacity of the filesystem in a built-in memory is shown. " ::= { ax3830sChassisEntry 14 } ax3830sSdCardStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The SD card connection is shown." ::= { ax3830sChassisEntry 15 } ax3830sSdCardTotalSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total capacity of the SD card is shown by the numerical value. It responds by -1 at the MC card unconnection." ::= { ax3830sChassisEntry 16 } ax3830sSdCardUsedSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The use capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection. " ::= { ax3830sChassisEntry 17 } ax3830sSdCardFreeSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The remainder capacity of the SD card is shown by the numerical value. It responds by -1 at the SD card unconnection." ::= { ax3830sChassisEntry 18 } ax3830sPhysLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of physical lines." ::= { ax3830sChassisEntry 19 } ax3830sTemperatureStatusNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of ax3830sTemperatureStatus in this chassis." ::= { ax3830sChassisEntry 20 } ax3830sPowerUnitNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of maximum power switches that this router can connect its." ::= { ax3830sChassisEntry 21 } ax3830sRedundantPsNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of external power switches that this router can connect its." ::= { ax3830sChassisEntry 22 } ax3830sFanNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of fans that can connect to this chassis." ::= { ax3830sChassisEntry 23 } ax3830sTotalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total operation time after operation of device begins." ::= { ax3830sChassisEntry 24 } ax3830sCriticalAccumRunTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Operating time under environment of 50 degrees C or more." ::= { ax3830sChassisEntry 25 } ax3830sModuleSlotNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of redundant power module that can connect to this chassis." ::= { ax3830sChassisEntry 26 } ax3830sMgmtPortStatus OBJECT-TYPE SYNTAX INTEGER { unsupported(0), active(2), down(4), disabled(6), maintenance(7), unused(10) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of management-port statusof the chassis." ::= { ax3830sChassisEntry 27 } ax3830sTemperatureStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of ambient temperature status maintained by the environmental monitor." ::= { ax3830sChassis 3 } ax3830sTemperatureStatusEntry OBJECT-TYPE SYNTAX Ax3830sTemperatureStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the ambient temperature status table, representing the status of the associated testpoint maintained by the environmental monitor." INDEX { ax3830sChassisIndex, ax3830sTemperatureStatusIndex } ::= { ax3830sTemperatureStatusTable 1 } Ax3830sTemperatureStatusEntry ::= SEQUENCE { ax3830sTemperatureStatusIndex INTEGER, ax3830sTemperatureStatusDescr DisplayString, ax3830sTemperatureStatusValue Integer32, ax3830sTemperatureThreshold Integer32, ax3830sTemperatureState INTEGER } ax3830sTemperatureStatusIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Unique index for the testpoint being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning." ::= { ax3830sTemperatureStatusEntry 1 } ax3830sTemperatureStatusDescr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) ACCESS read-only STATUS mandatory DESCRIPTION "Textual description of the testpoint being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry." ::= { ax3830sTemperatureStatusEntry 2 } ax3830sTemperatureStatusValue OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The current measurement of the testpoint being instrumented." ::= { ax3830sTemperatureStatusEntry 3 } ax3830sTemperatureThreshold OBJECT-TYPE SYNTAX Integer32 ACCESS read-only STATUS mandatory DESCRIPTION "The highest value that the associated instance of the object ax3830sTemperatureStatusValue may obtain before an emergency shutdown of the managed device is initiated." ::= { ax3830sTemperatureStatusEntry 4 } ax3830sTemperatureState OBJECT-TYPE SYNTAX INTEGER { normal(1), caution(2), warning(3), fatal(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the testpoint being instrumented." ::= { ax3830sTemperatureStatusEntry 5 } ax3830sPowerUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing power unit information." ::= { ax3830sChassis 4 } ax3830sPowerUnitEntry OBJECT-TYPE SYNTAX Ax3830sPowerUnitTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing power unit information." INDEX { ax3830sChassisIndex, ax3830sPowerUnitIndex } ::= { ax3830sPowerUnitTable 1 } Ax3830sPowerUnitTableEntry ::= SEQUENCE { ax3830sPowerUnitIndex INTEGER, ax3830sPowerConnectStatus INTEGER, ax3830sPowerSupplyStatus INTEGER, ax3830sPowerSlotType INTEGER, ax3830sPowerFanDirection INTEGER } ax3830sPowerUnitIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the power units.The value from 1 to ax3830sPowerUnitNumber." ::= { ax3830sPowerUnitEntry 1 } ax3830sPowerConnectStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The current connection status of the power unit." ::= { ax3830sPowerUnitEntry 2 } ax3830sPowerSupplyStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), fault(4), disconnected(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of power supply." ::= { ax3830sPowerUnitEntry 3 } ax3830sPowerSlotType OBJECT-TYPE SYNTAX INTEGER { powerModule-AC(1), powerModule-DC(2), unknown(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of power slot is shown." ::= { ax3830sPowerUnitEntry 4 } ax3830sPowerFanDirection OBJECT-TYPE SYNTAX INTEGER { front-to-rear(0), rear-to-front(1) } ACCESS read-only STATUS mandatory DESCRIPTION "The direction of fan of power supply is shown." ::= { ax3830sPowerUnitEntry 5 } ax3830sFanTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing fan information." ::= { ax3830sChassis 5 } ax3830sFanEntry OBJECT-TYPE SYNTAX Ax3830sFanTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entry containing information for a fan." INDEX { ax3830sChassisIndex, ax3830sFanIndex } ::= { ax3830sFanTable 1 } Ax3830sFanTableEntry ::= SEQUENCE { ax3830sFanIndex INTEGER, ax3830sFanStatus INTEGER, ax3830sFanDirection INTEGER } ax3830sFanIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Index to indicate position of fans." ::= { ax3830sFanEntry 1 } ax3830sFanStatus OBJECT-TYPE SYNTAX INTEGER { ok(2), high-speed(3), fault(4), unsupported(31), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of fans." ::= { ax3830sFanEntry 2 } ax3830sFanDirection OBJECT-TYPE SYNTAX INTEGER { front-to-rear(0), rear-to-front(1), unknown(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "The direction of main fan is shown." ::= { ax3830sFanEntry 3 } ax3830sModuleSlotTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing redundunt power module information." ::= { ax3830sChassis 7 } ax3830sModuleSlotEntry OBJECT-TYPE SYNTAX Ax3830sModuleSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing redundunt power module information." INDEX { ax3830sChassisIndex, ax3830sModuleSlotIndex } ::= { ax3830sModuleSlotTable 1 } Ax3830sModuleSlotEntry ::= SEQUENCE { ax3830sModuleSlotIndex INTEGER, ax3830sModuleSlotStatus INTEGER, ax3830sModuleSlotType INTEGER } ax3830sModuleSlotIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "A number to position of the module slot units.The value from 1 to ax3830sModuleSlotNumber." ::= { ax3830sModuleSlotEntry 1 } ax3830sModuleSlotStatus OBJECT-TYPE SYNTAX INTEGER { connected(2), down(4), disconnected(32) } ACCESS read-only STATUS mandatory DESCRIPTION "Module slot status is shown." ::= { ax3830sModuleSlotEntry 2 } ax3830sModuleSlotType OBJECT-TYPE SYNTAX INTEGER { powerModule-AC(1), powerModule-DC(2), unknown(-1) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of module slot is shown." ::= { ax3830sModuleSlotEntry 3 } ax3830sPhysLineTable OBJECT-TYPE SYNTAX SEQUENCE OF Ax3830sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing physical port information." ::= { ax3830sPhysLine 1 } ax3830sPhysLineEntry OBJECT-TYPE SYNTAX Ax3830sPhysLineTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry containing physical port." INDEX { ax3830sChassisIndex, ax3830sPhysLineIndex } ::= { ax3830sPhysLineTable 1 } Ax3830sPhysLineTableEntry ::= SEQUENCE { ax3830sPhysLineIndex INTEGER, ax3830sPhysLineConnectorType INTEGER, ax3830sPhysLineOperStatus INTEGER, ax3830sPhysLineIfIndexNumber INTEGER, ax3830sPhysLineTransceiverStatus INTEGER } ax3830sPhysLineIndex OBJECT-TYPE SYNTAX INTEGER ACCESS not-accessible STATUS mandatory DESCRIPTION "Physical port number. The value is from 1 to ax3830sNifLineNumber." ::= { ax3830sPhysLineEntry 1 } ax3830sPhysLineConnectorType OBJECT-TYPE SYNTAX INTEGER { other(1), type1000BASE-LX(301), type1000BASE-SX(302), type1000BASE-LH(303), type1000BASE-BX10-D(304), type1000BASE-BX10-U(305), type1000BASE-BX40-D(306), type1000BASE-BX40-U(307), type1000BASE-UTP(309), type1000BASE-LHB(310), type10GBASE-SR(401), type10GBASE-LR(402), type10GBASE-ER(403), type10GBASE-ZR(404), type10GBASE-CU1M(405), type10GBASE-CU3M(406), type10GBASE-CU5M(407), type10GBASE-CU30CM(408), type10GBASE-BR10-D(409), type10GBASE-BR10-U(410), type10GBASE-BR40-D(411), type10GBASE-BR40-U(412), type40GBASE-SR4(501), type40GBASE-CU35CM(502), type40GBASE-CU1M(503), type40GBASE-CU3M(504), type40GBASE-CU5M(505), type40GBASE-LR4(506) } ACCESS read-only STATUS mandatory DESCRIPTION "Connector type is connected physical port. The value is 1(other) when connector is disconnected or connector type is unknown." ::= { ax3830sPhysLineEntry 2 } ax3830sPhysLineOperStatus OBJECT-TYPE SYNTAX INTEGER { other(1), active(2), initialization(3), down(4), lock(6), close(7), line-fault(8), test(9), nothing-configuration(10) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of physical port. The value is -1 when PSU or NIF board is disconnected." ::= { ax3830sPhysLineEntry 3 } ax3830sPhysLineIfIndexNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of ifIndex which is included in physical port.The value is -1 when PSU board or NIF board is disconnected." ::= { ax3830sPhysLineEntry 4 } ax3830sPhysLineTransceiverStatus OBJECT-TYPE SYNTAX INTEGER { unchangeable-transceiver(1), sfp-mounted(20), sfp-unmounted(21), unsupported-sfp-mounted(22), sfp-status-unknown(23), qsfp-mounted(50), qsfp-unmounted(51), unsupported-qsfp-mounted(52), qsfp-status-unknown(53) } ACCESS read-only STATUS mandatory DESCRIPTION "Type and status of replaceable transceiver." ::= { ax3830sPhysLineEntry 5 } -- ax3830sFdbClearMIB group ax3830sFdbClearSet OBJECT-TYPE SYNTAX INTEGER { initialValue(0), processing(1), failure(2), success(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Fdb clear information. When want to clear fdb, then set value of this MIB as 1." ::= { ax3830sFdbClearMIB 1 } ax3830sFdbClearReqTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the most recent time that received the demand to clear Fdb information.(sysUpTime)" ::= { ax3830sFdbClearMIB 2 } ax3830sFdbClearSuccessTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "This object indicates the time of the most recent Fdb clearing success.(sysUpTime)" ::= { ax3830sFdbClearMIB 3 } -- Traps for use by AlaxalA networks AXS -- Traps are defined using the conventions in RFC 1215. axsStaticGatewayStateChange TRAP-TYPE ENTERPRISE axsStaticTrap VARIABLES { axsStaticGatewayAddr, axsStaticGatewayState } DESCRIPTION "static route gateway state change." ::= 1 axsStaticIpv6GatewayStateChange TRAP-TYPE ENTERPRISE axsStaticTrap VARIABLES { axsStaticIpv6Ifindex, axsStaticIpv6GatewayAddr, axsStaticIpv6GatewayState } DESCRIPTION "ipv6 static route gateway state change." ::= 2 axsOspfVirtIfStateChange TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfVirtIfDomainNumber, axsOspfRouterId, axsOspfVirtIfAreaId, axsOspfVirtIfNeighbor, axsOspfVirtIfState } DESCRIPTION "An axsOspfIfStateChange trap signifies that there has been a change in the state of an OSPF virtual interface." ::= 1 axsOspfNbrStateChange TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfNbrDomainNumber, axsOspfRouterId, axsOspfNbrIpAddr, axsOspfNbrAddressLessIndex, axsOspfNbrRtrId, axsOspfNbrState } DESCRIPTION "An axsOspfNbrStateChange trap signifies that there has been a change in the state of a non- virtual OSPF neighbor. This trap should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When an neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the trap should be gen- erated by the designated router. A designated router transitioning to Down will be noted by axsOspfIfStateChange." ::= 2 axsOspfVirtNbrStateChange TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfVirtNbrDomainNumber, axsOspfRouterId, axsOspfVirtNbrArea, axsOspfVirtNbrRtrId, axsOspfVirtNbrState } DESCRIPTION "An axsOspfIfStateChange trap signifies that there has been a change in the state of an OSPF vir- tual neighbor. This trap should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full)." ::= 3 axsOspfIfConfigError TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfIfDomainNumber, axsOspfRouterId, axsOspfIfIpAddress, axsOspfAddressLessIf, axsOspfPacketSrc, axsOspfConfigErrorType, axsOspfPacketType } DESCRIPTION "An axsOspfIfConfigError trap signifies that a packet has been received on a non-virtual in- terface from a router whose configuration parameters conflict with this router's confi- guration parameters. Note that the event op- tionMismatch should cause a trap only if it prevents an adjacency from forming." ::= 4 axsOspfVirtIfConfigError TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfVirtIfDomainNumber, axsOspfRouterId, axsOspfVirtIfAreaId, axsOspfVirtIfNeighbor, axsOspfConfigErrorType, axsOspfPacketType } DESCRIPTION "An axsOspfConfigError trap signifies that a pack- et has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a trap only if it prevents an ad- jacency from forming." ::= 5 axsOspfIfAuthFailure TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfIfDomainNumber, axsOspfRouterId, axsOspfIfIpAddress, axsOspfAddressLessIf, axsOspfPacketSrc, axsOspfConfigErrorType, axsOspfPacketType } DESCRIPTION "An axsOspfIfAuthFailure trap signifies that a packet has been received on a non-virtual in- terface from a router whose authentication key or authentication type conflicts with this router's authentication key or authentication type." ::= 6 axsOspfVirtIfAuthFailure TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfVirtIfDomainNumber, axsOspfRouterId, axsOspfVirtIfAreaId, axsOspfVirtIfNeighbor, axsOspfConfigErrorType, axsOspfPacketType } DESCRIPTION "An axsOspfVirtIfAuthFailure trap signifies that a packet has been received on a virtual interface from a router whose authentication key or au- thentication type conflicts with this router's authentication key or authentication type." ::= 7 axsOspfIfStateChange TRAP-TYPE ENTERPRISE axsOspfTraps VARIABLES { axsOspfIfDomainNumber, axsOspfRouterId, axsOspfIfIpAddress, axsOspfAddressLessIf, axsOspfIfState } DESCRIPTION "An axsOspfIfStateChange trap signifies that there has been a change in the state of a non-virtual OSPF interface. This trap should be generated when the interface state regresses (e.g., goes from Dr to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, Dr, or Backup)." ::= 16 axsOadpNeighborCachelastChangeTrap TRAP-TYPE ENTERPRISE axsOadpMIBNotifications VARIABLES { axsOadpNeighborCacheLastChange } DESCRIPTION "This trap indicates that information of OADP neighbor nodes is updated." ::= 1 axsPolicyBaseRoutingRouteChange TRAP-TYPE ENTERPRISE axsPolicyBaseRouting VARIABLES {axsPolicyBaseRoutingChangeListNumber , axsPolicyBaseRoutingChangeSequenceNumber} DESCRIPTION "When route of Policy Base Routing changed." ::= 1 axsTrackObjectStateUp TRAP-TYPE ENTERPRISE axsTrackObjectTraps VARIABLES { axsTrackObjectId, axsTrackObjectState, axsTrackObjectOperation, axsTrackObjectType, axsTrackObjectNetIndex } DESCRIPTION "The track state changed to up." ::= 1 axsTrackObjectStateDown TRAP-TYPE ENTERPRISE axsTrackObjectTraps VARIABLES { axsTrackObjectId, axsTrackObjectState, axsTrackObjectOperation, axsTrackObjectType, axsTrackObjectNetIndex } DESCRIPTION "The track state changed to down." ::= 2 END AXS-AX3630S-TRAP DEFINITIONS ::= BEGIN IMPORTS enterprises FROM RFC1155-SMI TRAP-TYPE FROM RFC-1215 ifIndex FROM RFC1213-MIB ax3630s, axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMonitoringState, axsAxrpGroupRingport1, axsAxrpGroupRingport2, axsAxrpGroupMultiFaultDetectionState, ax3630sSystemMsgType, ax3630sSystemMsgTimeStamp, ax3630sSystemMsgLevel, ax3630sSystemMsgEventPoint, ax3630sSystemMsgEventInterfaceID, ax3630sSystemMsgEventCode, ax3630sSystemMsgAdditionalCode, ax3630sSystemMsgText, ax3630sChassisIndex, ax3630sTemperatureStatusIndex, ax3630sTemperatureStatusDescr, ax3630sTemperatureStatusValue, ax3630sTemperatureState, axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState, axsLoginName, axsLoginTime, axsLoginLocation, axsLoginLine, axsLoginFailureTime, axsLogoutTime, axsLogoutStatus, axsL2ldPortIndex, axsL2ldPortIfIndex, axsL2ldPortSourcePortIfindex, axsL2ldPortDestinationPortIfindex, axsL2ldPortSourceVlan, axsUlrPortIfIndex, axsUlrPairedPortIfIndex FROM AX3630S ; -- Traps for use by AlaxalA networks AX3630S -- Traps are defined using the conventions in RFC 1215. --axsAxrpStateTransitionTrap TRAP-TYPE ax3630sAxrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMonitoringState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (trouble watch and restoration watch) changes between each state. " ::= 36 --axsAxrpRingport1MonitoringStartTrap TRAP-TYPE ax3630sAxrpRingport1MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport1 } DESCRIPTION "When you make the link monitoring function of ring port 1 of Ring Protocol effective. " ::= 37 --axsAxrpRingport1DownTrap TRAP-TYPE ax3630sAxrpRingport1DownTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport1 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 1 of Ring Protocol is made effective. " ::= 38 --axsAxrpRingport2MonitoringStartTrap TRAP-TYPE ax3630sAxrpRingport2MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport2 } DESCRIPTION "When you make the link monitoring function of ring port 2 of Ring Protocol effective. " ::= 39 --axsAxrpRingport2DownTrap TRAP-TYPE ax3630sAxrpRingport2DownTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport2 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 2 of Ring Protocol is made effective. " ::= 40 ax3630sAxrpMultiFaultDetectionStartTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute } DESCRIPTION "When you make the multiple fault detection function of Ring Protocol effective. " ::= 41 ax3630sAxrpMultiFaultDetectionStateTransitionTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMultiFaultDetectionState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (multiple fault detection and restoration watch) changes between each state. " ::= 42 ax3630sSystemMsgTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ax3630sSystemMsgType, ax3630sSystemMsgTimeStamp, ax3630sSystemMsgLevel, ax3630sSystemMsgEventPoint, ax3630sSystemMsgEventInterfaceID, ax3630sSystemMsgEventCode, ax3630sSystemMsgAdditionalCode, ax3630sSystemMsgText } DESCRIPTION "System message is displayed." ::= 1 ax3630sStandbySystemUpTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ax3630sChassisIndex } DESCRIPTION "Standby system is restarted." ::= 2 ax3630sStandbySystemDownTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ax3630sChassisIndex } DESCRIPTION "Standby system is failed." ::= 3 ax3630sTemperatureTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ax3630sChassisIndex, ax3630sTemperatureStatusIndex, ax3630sTemperatureStatusDescr, ax3630sTemperatureStatusValue, ax3630sTemperatureState } DESCRIPTION "An ax3660sTemperatureTrap is sent if the temperature measured at a given testpoint falls outside the normal range or recovers from that state. (i.e. when becoming the warning, critical, or normal state)." ::= 4 --axsGsrpStateTransitionTrap TRAP-TYPE ax3630sGsrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState } DESCRIPTION "Changes of the VLAN group state of GSRP" ::= 6 ax3630sEoeMsgTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ax3630sSystemMsgType, ax3630sSystemMsgTimeStamp, ax3630sSystemMsgLevel, ax3630sSystemMsgEventPoint, ax3630sSystemMsgEventInterfaceID, ax3630sSystemMsgEventCode, ax3630sSystemMsgAdditionalCode, ax3630sSystemMsgText } DESCRIPTION "The notice of a message of EoE" ::= 7 ax3630sAirFanStopTrap TRAP-TYPE ENTERPRISE ax3630s DESCRIPTION "This trap indicates a fan failure." ::= 8 ax3630sPowerSupplyFailureTrap TRAP-TYPE ENTERPRISE ax3630s DESCRIPTION "This trap indicates one ( or more ) of power supplies failure." ::= 9 ax3630sLoginSuccessTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsLoginName, axsLoginTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates success of user log in." ::= 10 ax3630sLoginFailureTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsLoginName, axsLoginFailureTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates failure of user log in." ::= 11 ax3630sLogoutTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsLoginName, axsLoginTime, axsLogoutTime, axsLoginLocation, axsLoginLine, axsLogoutStatus } DESCRIPTION "This trap indicates success of following log out. 'logout' command, 'exit' command, 'quit' command." ::= 12 ax3630sMemoryUsageTrap TRAP-TYPE ENTERPRISE ax3630s DESCRIPTION "This indicates available memory is fewer than lower limit." ::= 13 ax3630sFrameErrorReceiveTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates frame receive error." ::= 18 ax3630sFrameErrorSendTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates frame send error." ::= 19 --axsBroadcastStormDetectTrap TRAP-TYPE ax3630sBroadcastStormDetectTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on broad-cast storm." ::= 20 --axsMulticastStormDetectTrap TRAP-TYPE ax3630sMulticastStormDetectTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on multi-cast storm." ::= 21 --axsUnicastStormDetectTrap TRAP-TYPE ax3630sUnicastStormDetectTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on uni-cast storm." ::= 22 --axsBroadcastStormPortInactivateTrap TRAP-TYPE ax3630sBroadcastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on broad-cast storm." ::= 23 --axsMulticastStormPortInactivateTrap TRAP-TYPE ax3630sMulticastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on multi-cast storm." ::= 24 --axsUnicastStormPortInactivateTrap TRAP-TYPE ax3630sUnicastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on uni-cast storm." ::= 25 --axsBroadcastStormRecoverTrap TRAP-TYPE ax3630sBroadcastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of broad-cast storm." ::= 26 --axsMulticastStormRecoverTrap TRAP-TYPE ax3630sMulticastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of multi-cast storm." ::= 27 --axsUnicastStormRecoverTrap TRAP-TYPE ax3630sUnicastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of uni-cast storm." ::= 28 --axsEfmoamUdldPortInactivateTrap TRAP-TYPE ax3630sEfmoamUdldPortInactivateTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "Efmoam udld port inactivate trap." ::= 29 --axsEfmoamLoopDetectPortInactivateTrap TRAP-TYPE ax3630sEfmoamLoopDetectPortInactivateTrap TRAP-TYPE ENTERPRISE ax3630s VARIABLES { ifIndex } DESCRIPTION "Efmoam loop detect port inactivate trap." ::= 30 --axsL2ldLinkDown TRAP-TYPE ax3630sL2ldLinkDown TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsL2ldPortIfIndex,axsL2ldPortSourcePortIfindex,axsL2ldPortDestinationPortIfindex,axsL2ldPortSourceVlan } DESCRIPTION "When the operation of the interface changes from ACTIVE(state that can be communicated) into DISABLE (state that cannot be communicated) by the L2 loop detection." ::= 51 --axsL2ldLinkUp TRAP-TYPE ax3630sL2ldLinkUp TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsL2ldPortIfIndex } DESCRIPTION "When the operation of the interface changes from DISABLE (state that cannot be communicated) into ACTIVE (state that can be communicated) by the automatic restoration function of the L2 loop detection." ::= 52 --axsL2ldLoopDetection TRAP-TYPE ax3630sL2ldLoopDetection TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsL2ldPortIndex,axsL2ldPortIfIndex,axsL2ldPortSourcePortIfindex,axsL2ldPortSourceVlan } DESCRIPTION "When you detect the L2 loop. It notifies every 60 seconds when the state of the L2 loop continues." ::= 53 ax3630sUlrChangeSecondary TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When secondary port changed to active port." ::= 87 ax3630sUlrChangePrimary TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When primary port changed to active port." ::= 88 ax3630sUlrActivePortDown TRAP-TYPE ENTERPRISE ax3630s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When active port disappeared." ::= 89 END AXS-AX3640S-TRAP DEFINITIONS ::= BEGIN IMPORTS enterprises FROM RFC1155-SMI TRAP-TYPE FROM RFC-1215 ifIndex FROM RFC1213-MIB ax3640s, axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMonitoringState, axsAxrpGroupRingport1, axsAxrpGroupRingport2,axsAxrpGroupMultiFaultDetectionState, ax3640sSystemMsgType, ax3640sSystemMsgTimeStamp, ax3640sSystemMsgLevel, ax3640sSystemMsgEventPoint, ax3640sSystemMsgEventInterfaceID, ax3640sSystemMsgEventCode, ax3640sSystemMsgAdditionalCode, ax3640sSystemMsgText, ax3640sChassisIndex, ax3640sTemperatureStatusIndex, ax3640sTemperatureStatusDescr, ax3640sTemperatureStatusValue, ax3640sTemperatureState, axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState, axsLoginName, axsLoginTime, axsLoginLocation, axsLoginLine, axsLoginFailureTime, axsLogoutTime, axsLogoutStatus, axsL2ldPortIndex, axsL2ldPortIfIndex, axsL2ldPortSourcePortIfindex, axsL2ldPortDestinationPortIfindex, axsL2ldPortSourceVlan, axsUlrPortIfIndex, axsUlrPairedPortIfIndex FROM AX3630S ; -- Traps for use by AlaxalA networks AX3640S -- Traps are defined using the conventions in RFC 1215. --axsAxrpStateTransitionTrap TRAP-TYPE ax3640sAxrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMonitoringState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (trouble watch and restoration watch) changes between each state. " ::= 36 --axsAxrpRingport1MonitoringStartTrap TRAP-TYPE ax3640sAxrpRingport1MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport1 } DESCRIPTION "When you make the link monitoring function of ring port 1 of Ring Protocol effective. " ::= 37 --axsAxrpRingport1DownTrap TRAP-TYPE ax3640sAxrpRingport1DownTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport1 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 1 of Ring Protocol is made effective. " ::= 38 --axsAxrpRingport2MonitoringStartTrap TRAP-TYPE ax3640sAxrpRingport2MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport2 } DESCRIPTION "When you make the link monitoring function of ring port 2 of Ring Protocol effective. " ::= 39 --axsAxrpRingport2DownTrap TRAP-TYPE ax3640sAxrpRingport2DownTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport2 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 2 of Ring Protocol is made effective. " ::= 40 ax3640sAxrpMultiFaultDetectionStartTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute } DESCRIPTION "When the state of watching muliple trouble on ring started." ::= 41 ax3640sAxrpMultiFaultDetectionStateTransitionTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMultiFaultDetectionState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (multiple fault detection and restoration watch) changes between each state. " ::= 42 ax3640sSystemMsgTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ax3640sSystemMsgType, ax3640sSystemMsgTimeStamp, ax3640sSystemMsgLevel, ax3640sSystemMsgEventPoint, ax3640sSystemMsgEventInterfaceID, ax3640sSystemMsgEventCode, ax3640sSystemMsgAdditionalCode, ax3640sSystemMsgText } DESCRIPTION "System message is displayed." ::= 1 ax3640sStandbySystemUpTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ax3640sChassisIndex } DESCRIPTION "Standby system is restarted." ::= 2 ax3640sStandbySystemDownTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ax3640sChassisIndex } DESCRIPTION "Standby system is failed." ::= 3 ax3640sTemperatureTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ax3640sChassisIndex, ax3640sTemperatureStatusIndex, ax3640sTemperatureStatusDescr, ax3640sTemperatureStatusValue, ax3640sTemperatureState } DESCRIPTION "A ax3640sTemperatureTrap is sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e. is at the warning, critical, or shutdown stage)." ::= 4 --axsGsrpStateTransitionTrap TRAP-TYPE ax3640sGsrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState } DESCRIPTION "Changes of the VLAN group state of GSRP" ::= 6 ax3640sEoeMsgTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ax3640sSystemMsgType, ax3640sSystemMsgTimeStamp, ax3640sSystemMsgLevel, ax3640sSystemMsgEventPoint, ax3640sSystemMsgEventInterfaceID, ax3640sSystemMsgEventCode, ax3640sSystemMsgAdditionalCode, ax3640sSystemMsgText } DESCRIPTION "The notice of a message of EoE" ::= 7 ax3640sAirFanStopTrap TRAP-TYPE ENTERPRISE ax3640s DESCRIPTION "This trap indicates a fan failure." ::= 8 ax3640sPowerSupplyFailureTrap TRAP-TYPE ENTERPRISE ax3640s DESCRIPTION "This trap indicates one ( or more ) of power supplies failure." ::= 9 ax3640sLoginSuccessTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsLoginName, axsLoginTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates success of user log in." ::= 10 ax3640sLoginFailureTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsLoginName, axsLoginFailureTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates failure of user log in." ::= 11 ax3640sLogoutTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsLoginName, axsLoginTime, axsLogoutTime, axsLoginLocation, axsLoginLine, axsLogoutStatus } DESCRIPTION "This trap indicates success of following log out. 'logout' command, 'exit' command, 'quit' command." ::= 12 ax3640sMemoryUsageTrap TRAP-TYPE ENTERPRISE ax3640s DESCRIPTION "This indicates available memory is fewer than lower limit." ::= 13 ax3640sFrameErrorReceiveTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates frame receive error." ::= 18 ax3640sFrameErrorSendTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates frame send error." ::= 19 --axsBroadcastStormDetectTrap TRAP-TYPE ax3640sBroadcastStormDetectTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on broad-cast storm." ::= 20 --axsMulticastStormDetectTrap TRAP-TYPE ax3640sMulticastStormDetectTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on multi-cast storm." ::= 21 --axsUnicastStormDetectTrap TRAP-TYPE ax3640sUnicastStormDetectTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on uni-cast storm." ::= 22 --axsBroadcastStormPortInactivateTrap TRAP-TYPE ax3640sBroadcastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on broad-cast storm." ::= 23 --axsMulticastStormPortInactivateTrap TRAP-TYPE ax3640sMulticastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on multi-cast storm." ::= 24 --axsUnicastStormPortInactivateTrap TRAP-TYPE ax3640sUnicastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on uni-cast storm." ::= 25 --axsBroadcastStormRecoverTrap TRAP-TYPE ax3640sBroadcastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of broad-cast storm." ::= 26 --axsMulticastStormRecoverTrap TRAP-TYPE ax3640sMulticastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of multi-cast storm." ::= 27 --axsUnicastStormRecoverTrap TRAP-TYPE ax3640sUnicastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of uni-cast storm." ::= 28 --axsEfmoamUdldPortInactivateTrap TRAP-TYPE ax3640sEfmoamUdldPortInactivateTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "Efmoam udld port inactivate trap." ::= 29 --axsEfmoamLoopDetectPortInactivateTrap TRAP-TYPE ax3640sEfmoamLoopDetectPortInactivateTrap TRAP-TYPE ENTERPRISE ax3640s VARIABLES { ifIndex } DESCRIPTION "Efmoam loop detect port inactivate trap." ::= 30 --axsL2ldLinkDown TRAP-TYPE ax3640sL2ldLinkDown TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsL2ldPortIfIndex,axsL2ldPortSourcePortIfindex,axsL2ldPortDestinationPortIfindex,axsL2ldPortSourceVlan } DESCRIPTION "When the operation of the interface changes from ACTIVE(state that can be communicated) into DISABLE (state that cannot be communicated) by the L2 loop detection." ::= 51 --axsL2ldLinkUp TRAP-TYPE ax3640sL2ldLinkUp TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsL2ldPortIfIndex } DESCRIPTION "When the operation of the interface changes from DISABLE (state that cannot be communicated) into ACTIVE (state that can be communicated) by the automatic restoration function of the L2 loop detection." ::= 52 --axsL2ldLoopDetection TRAP-TYPE ax3640sL2ldLoopDetection TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsL2ldPortIndex,axsL2ldPortIfIndex,axsL2ldPortSourcePortIfindex,axsL2ldPortSourceVlan } DESCRIPTION "When you detect the L2 loop. It notifies every 60 seconds when the state of the L2 loop continues." ::= 53 ax3640sUlrChangeSecondary TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When secondary port changed to active port." ::= 87 ax3640sUlrChangePrimary TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When primary port changed to active port." ::= 88 ax3640sUlrActivePortDown TRAP-TYPE ENTERPRISE ax3640s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When active port disappeared." ::= 89 END AXS-AX3650S-TRAP DEFINITIONS ::= BEGIN IMPORTS enterprises FROM RFC1155-SMI TRAP-TYPE FROM RFC-1215 ifIndex FROM RFC1213-MIB ax3650s, axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMonitoringState, axsAxrpGroupRingport1, axsAxrpGroupRingport2,axsAxrpGroupMultiFaultDetectionState, ax3650sSystemMsgType, ax3650sSystemMsgTimeStamp, ax3650sSystemMsgLevel, ax3650sSystemMsgEventPoint, ax3650sSystemMsgEventInterfaceID, ax3650sSystemMsgEventCode, ax3650sSystemMsgAdditionalCode, ax3650sSystemMsgText, ax3650sChassisIndex, ax3650sTemperatureStatusIndex, ax3650sTemperatureStatusDescr, ax3650sTemperatureStatusValue, ax3650sTemperatureState, axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState, axsLoginName, axsLoginTime, axsLoginLocation, axsLoginLine, axsLoginFailureTime, axsLogoutTime, axsLogoutStatus, axsL2ldPortIndex, axsL2ldPortIfIndex, axsL2ldPortSourcePortIfindex, axsL2ldPortDestinationPortIfindex, axsL2ldPortSourceVlan, axsUlrPortIfIndex, axsUlrPairedPortIfIndex FROM AX3630S ; -- Traps for use by AlaxalA networks AX3650S -- Traps are defined using the conventions in RFC 1215. --axsAxrpStateTransitionTrap TRAP-TYPE ax3650sAxrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMonitoringState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (trouble watch and restoration watch) changes between each state. " ::= 36 --axsAxrpRingport1MonitoringStartTrap TRAP-TYPE ax3650sAxrpRingport1MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport1 } DESCRIPTION "When you make the link monitoring function of ring port 1 of Ring Protocol effective. " ::= 37 --axsAxrpRingport1DownTrap TRAP-TYPE ax3650sAxrpRingport1DownTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport1 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 1 of Ring Protocol is made effective. " ::= 38 --axsAxrpRingport2MonitoringStartTrap TRAP-TYPE ax3650sAxrpRingport2MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport2 } DESCRIPTION "When you make the link monitoring function of ring port 2 of Ring Protocol effective. " ::= 39 --axsAxrpRingport2DownTrap TRAP-TYPE ax3650sAxrpRingport2DownTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupRingport2 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 2 of Ring Protocol is made effective. " ::= 40 ax3650sAxrpMultiFaultDetectionStartTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute } DESCRIPTION "When the state of watching muliple trouble on ring started." ::= 41 ax3650sAxrpMultiFaultDetectionStateTransitionTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsAxrpGroupRingId,axsAxrpGroupMode,axsAxrpGroupRingAttribute,axsAxrpGroupMultiFaultDetectionState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (multiple fault detection and restoration watch) changes between each state. " ::= 42 ax3650sSystemMsgTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ax3650sSystemMsgType, ax3650sSystemMsgTimeStamp, ax3650sSystemMsgLevel, ax3650sSystemMsgEventPoint, ax3650sSystemMsgEventInterfaceID, ax3650sSystemMsgEventCode, ax3650sSystemMsgAdditionalCode, ax3650sSystemMsgText } DESCRIPTION "System message is displayed." ::= 1 ax3650sStandbySystemUpTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ax3650sChassisIndex } DESCRIPTION "Standby system is restarted." ::= 2 ax3650sStandbySystemDownTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ax3650sChassisIndex } DESCRIPTION "Standby system is failed." ::= 3 ax3650sTemperatureTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ax3650sChassisIndex, ax3650sTemperatureStatusIndex, ax3650sTemperatureStatusDescr, ax3650sTemperatureStatusValue, ax3650sTemperatureState } DESCRIPTION "A ax3650sTemperatureTrap is sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e. is at the warning, critical, or shutdown stage)." ::= 4 --axsGsrpStateTransitionTrap TRAP-TYPE ax3650sGsrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState } DESCRIPTION "Changes of the VLAN group state of GSRP" ::= 6 ax3650sEoeMsgTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ax3650sSystemMsgType, ax3650sSystemMsgTimeStamp, ax3650sSystemMsgLevel, ax3650sSystemMsgEventPoint, ax3650sSystemMsgEventInterfaceID, ax3650sSystemMsgEventCode, ax3650sSystemMsgAdditionalCode, ax3650sSystemMsgText } DESCRIPTION "The notice of a message of EoE" ::= 7 ax3650sAirFanStopTrap TRAP-TYPE ENTERPRISE ax3650s DESCRIPTION "This trap indicates a fan failure." ::= 8 ax3650sPowerSupplyFailureTrap TRAP-TYPE ENTERPRISE ax3650s DESCRIPTION "This trap indicates one ( or more ) of power supplies failure." ::= 9 ax3650sLoginSuccessTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsLoginName, axsLoginTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates success of user log in." ::= 10 ax3650sLoginFailureTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsLoginName, axsLoginFailureTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates failure of user log in." ::= 11 ax3650sLogoutTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsLoginName, axsLoginTime, axsLogoutTime, axsLoginLocation, axsLoginLine, axsLogoutStatus } DESCRIPTION "This trap indicates success of following log out. 'logout' command, 'exit' command, 'quit' command." ::= 12 ax3650sMemoryUsageTrap TRAP-TYPE ENTERPRISE ax3650s DESCRIPTION "This indicates available memory is fewer than lower limit." ::= 13 ax3650sFrameErrorReceiveTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates frame receive error." ::= 18 ax3650sFrameErrorSendTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates frame send error." ::= 19 --axsBroadcastStormDetectTrap TRAP-TYPE ax3650sBroadcastStormDetectTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on broad-cast storm." ::= 20 --axsMulticastStormDetectTrap TRAP-TYPE ax3650sMulticastStormDetectTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on multi-cast storm." ::= 21 --axsUnicastStormDetectTrap TRAP-TYPE ax3650sUnicastStormDetectTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on uni-cast storm." ::= 22 --axsBroadcastStormPortInactivateTrap TRAP-TYPE ax3650sBroadcastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on broad-cast storm." ::= 23 --axsMulticastStormPortInactivateTrap TRAP-TYPE ax3650sMulticastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on multi-cast storm." ::= 24 --axsUnicastStormPortInactivateTrap TRAP-TYPE ax3650sUnicastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on uni-cast storm." ::= 25 --axsBroadcastStormRecoverTrap TRAP-TYPE ax3650sBroadcastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of broad-cast storm." ::= 26 --axsMulticastStormRecoverTrap TRAP-TYPE ax3650sMulticastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of multi-cast storm." ::= 27 --axsUnicastStormRecoverTrap TRAP-TYPE ax3650sUnicastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of uni-cast storm." ::= 28 --axsEfmoamUdldPortInactivateTrap TRAP-TYPE ax3650sEfmoamUdldPortInactivateTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "Efmoam udld port inactivate trap." ::= 29 --axsEfmoamLoopDetectPortInactivateTrap TRAP-TYPE ax3650sEfmoamLoopDetectPortInactivateTrap TRAP-TYPE ENTERPRISE ax3650s VARIABLES { ifIndex } DESCRIPTION "Efmoam loop detect port inactivate trap." ::= 30 --axsL2ldLinkDown TRAP-TYPE ax3650sL2ldLinkDown TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsL2ldPortIfIndex,axsL2ldPortSourcePortIfindex,axsL2ldPortDestinationPortIfindex,axsL2ldPortSourceVlan } DESCRIPTION "When the operation of the interface changes from ACTIVE(state that can be communicated) into DISABLE (state that cannot be communicated) by the L2 loop detection." ::= 51 --axsL2ldLinkUp TRAP-TYPE ax3650sL2ldLinkUp TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsL2ldPortIfIndex } DESCRIPTION "When the operation of the interface changes from DISABLE (state that cannot be communicated) into ACTIVE (state that can be communicated) by the automatic restoration function of the L2 loop detection." ::= 52 --axsL2ldLoopDetection TRAP-TYPE ax3650sL2ldLoopDetection TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsL2ldPortIndex,axsL2ldPortIfIndex,axsL2ldPortSourcePortIfindex,axsL2ldPortSourceVlan } DESCRIPTION "When you detect the L2 loop. It notifies every 60 seconds when the state of the L2 loop continues." ::= 53 ax3650sUlrChangeSecondary TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When secondary port changed to active port." ::= 87 ax3650sUlrChangePrimary TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When primary port changed to active port." ::= 88 ax3650sUlrActivePortDown TRAP-TYPE ENTERPRISE ax3650s VARIABLES { axsUlrPortIfIndex,axsUlrPairedPortIfIndex } DESCRIPTION "When active port disappeared." ::= 89 END AXS-AX3830S-TRAP DEFINITIONS ::= BEGIN IMPORTS TRAP-TYPE FROM RFC-1215 ifIndex FROM RFC1213-MIB axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState, axsL2ldPortIndex, axsL2ldPortIfIndex, axsL2ldPortSourcePortIfindex, axsL2ldPortDestinationPortIfindex, axsL2ldPortSourceVlan, axsUlrPortIfIndex, axsUlrPairedPortIfIndex, axsLoginName, axsLoginTime, axsLogoutTime, axsLoginFailureTime, axsLoginLocation, axsLoginLine, axsLogoutStatus, axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute, axsAxrpGroupMonitoringState, axsAxrpGroupRingport1, axsAxrpGroupRingport2, axsAxrpGroupMultiFaultDetectionState, ax3830s, ax3830sSystemMsgType, ax3830sSystemMsgTimeStamp, ax3830sSystemMsgLevel, ax3830sSystemMsgEventPoint, ax3830sSystemMsgEventInterfaceID, ax3830sSystemMsgEventCode, ax3830sSystemMsgAdditionalCode, ax3830sSystemMsgText, ax3830sChassisIndex, ax3830sTemperatureStatusIndex, ax3830sTemperatureStatusDescr, ax3830sTemperatureStatusValue, ax3830sTemperatureState FROM AX3630S ; -- Traps for use by AlaxalA networks AX3830S -- Traps are defined using the conventions in RFC 1215. ax3830sSystemMsgTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ax3830sSystemMsgType, ax3830sSystemMsgTimeStamp, ax3830sSystemMsgLevel, ax3830sSystemMsgEventPoint, ax3830sSystemMsgEventInterfaceID, ax3830sSystemMsgEventCode, ax3830sSystemMsgAdditionalCode, ax3830sSystemMsgText } DESCRIPTION "System message is displayed." ::= 1 ax3830sTemperatureTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ax3830sChassisIndex, ax3830sTemperatureStatusIndex, ax3830sTemperatureStatusDescr, ax3830sTemperatureStatusValue, ax3830sTemperatureState } DESCRIPTION "A ax3830sTemperatureTrap is sent if the temperature measured at a given testpoint is outside the normal range for the testpoint (i.e. is at the warning, critical, or shutdown stage)." ::= 4 ax3830sGsrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsGsrpGroupId, axsGsrpVlanGroupId, axsGsrpState } DESCRIPTION "Changes of the VLAN group state of GSRP" ::= 6 ax3830sAirFanStopTrap TRAP-TYPE ENTERPRISE ax3830s DESCRIPTION "This trap indicates a fan failure." ::= 8 ax3830sPowerSupplyFailureTrap TRAP-TYPE ENTERPRISE ax3830s DESCRIPTION "This trap indicates one ( or more ) of power supplies failure." ::= 9 ax3830sLoginSuccessTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsLoginName, axsLoginTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates success of user log in." ::= 10 ax3830sLoginFailureTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsLoginName, axsLoginFailureTime, axsLoginLocation, axsLoginLine } DESCRIPTION "This trap indicates failure of user log in." ::= 11 ax3830sLogoutTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsLoginName, axsLoginTime, axsLogoutTime, axsLoginLocation, axsLoginLine, axsLogoutStatus } DESCRIPTION "This trap indicates success of following log out. 'logout' command, 'exit' command, 'quit' command." ::= 12 ax3830sMemoryUsageTrap TRAP-TYPE ENTERPRISE ax3830s DESCRIPTION "This indicates available memory is fewer than lower limit." ::= 13 ax3830sFrameErrorReceiveTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates frame receive error." ::= 18 ax3830sFrameErrorSendTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates frame send error." ::= 19 ax3830sBroadcastStormDetectTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on broad-cast storm." ::= 20 ax3830sMulticastStormDetectTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on multi-cast storm." ::= 21 ax3830sUnicastStormDetectTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates decection on uni-cast storm." ::= 22 ax3830sBroadcastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on broad-cast storm." ::= 23 ax3830sMulticastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on multi-cast storm." ::= 24 ax3830sUnicastStormPortInactivateTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates the port inactivated for decection on uni-cast storm." ::= 25 ax3830sBroadcastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of broad-cast storm." ::= 26 ax3830sMulticastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of multi-cast storm." ::= 27 ax3830sUnicastStormRecoverTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "This indicates the end of uni-cast storm." ::= 28 ax3830sEfmoamUdldPortInactivateTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "Efmoam udld port inactivate trap." ::= 29 ax3830sEfmoamLoopDetectPortInactivateTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { ifIndex } DESCRIPTION "Efmoam loop detect port inactivate trap." ::= 30 ax3830sAxrpStateTransitionTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute, axsAxrpGroupMonitoringState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (trouble watch and restoration watch) changes between each state. " ::= 36 ax3830sAxrpRingport1MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute, axsAxrpGroupRingport1 } DESCRIPTION "When you make the link monitoring function of ring port 1 of Ring Protocol effective. " ::= 37 ax3830sAxrpRingport1DownTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute, axsAxrpGroupRingport1 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 1 of Ring Protocol is made effective. " ::= 38 ax3830sAxrpRingport2MonitoringStartTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute, axsAxrpGroupRingport2 } DESCRIPTION "When you make the link monitoring function of ring port 2 of Ring Protocol effective. " ::= 39 ax3830sAxrpRingport2DownTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute, axsAxrpGroupRingport2 } DESCRIPTION "When the link for the watch is cut when the link monitoring function of ring port 2 of Ring Protocol is made effective. " ::= 40 ax3830sAxrpMultiFaultDetectionStartTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute } DESCRIPTION "When the state of watching muliple trouble on ring started." ::= 41 ax3830sAxrpMultiFaultDetectionStateTransitionTrap TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsAxrpGroupRingId, axsAxrpGroupMode, axsAxrpGroupRingAttribute, axsAxrpGroupMultiFaultDetectionState } DESCRIPTION "When the state of the ring of ALAXALA Ring Protocol (multiple fault detection and restoration watch) changes between each state. " ::= 42 ax3830sL2ldLinkDown TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsL2ldPortIfIndex, axsL2ldPortSourcePortIfindex, axsL2ldPortDestinationPortIfindex, axsL2ldPortSourceVlan } DESCRIPTION "When the operation of the interface changes from ACTIVE(state that can be communicated) into DISABLE (state that cannot be communicated) by the L2 loop detection." ::= 51 ax3830sL2ldLinkUp TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsL2ldPortIfIndex } DESCRIPTION "When the operation of the interface changes from DISABLE (state that cannot be communicated) into ACTIVE (state that can be communicated) by the automatic restoration function of the L2 loop detection." ::= 52 ax3830sL2ldLoopDetection TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsL2ldPortIndex, axsL2ldPortIfIndex, axsL2ldPortSourcePortIfindex, axsL2ldPortSourceVlan } DESCRIPTION "When you detect the L2 loop. It notifies every 60 seconds when the state of the L2 loop continues." ::= 53 ax3830sUlrChangeSecondary TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsUlrPortIfIndex, axsUlrPairedPortIfIndex } DESCRIPTION "When secondary port changed to active port." ::= 87 ax3830sUlrChangePrimary TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsUlrPortIfIndex, axsUlrPairedPortIfIndex } DESCRIPTION "When primary port changed to active port." ::= 88 ax3830sUlrActivePortDown TRAP-TYPE ENTERPRISE ax3830s VARIABLES { axsUlrPortIfIndex, axsUlrPairedPortIfIndex } DESCRIPTION "When active port disappeared." ::= 89 END